Grange EXTENDED DRAGON PERGOLA User manual

x
x
x
ASSEMBLY (cont.)
STEP 7
Fix the ‘U’ Clips (z)to the top of
the assembly as shown in fig.4.
STEP 8
Take one of the Centre Blocks
(J)and fix three of the Short
Curved Beams (E)as fig.5.
STEP 9
Repeat for the second centre
block.
STEP 10
Raise the two assemblies in
turn and position as shown in
Fig.6.
STEP 11
Fix the Joist (G)to the centre
blocks using screws (y)as
shown in fig.7.
STEP 12
Set the position of the curved
beams in the ‘U’ clips so that
they sit evenly on the frame.
STEP 13
Fix the four Longer Curved
Beams (F)to the centreblocks
so that they locate in each of
the four corners of the frame.
STEP 14
Now fix the four remaining
shortcurved beams to the joist
to locate as shown in fig.8.
STEP 15
Finally,fix the Round Finials
(H)to the tops of the centre
blocks.
FIX THE 14 U CLIPS TO THE TOP
OF THE RAFTERS AS SHOWN
FIX JOIST TO EACH
CENTRE PIECE
WITH TWO SCREWS
(TOP AND BOTTOM)
(fig.4)
(fig.5)
(fig.6)
(fig.8)
(fig.7)
z
ww
w
zz
zz
zzzz
zzz z
z
z
z
z
z
J
J
D
D
E
E
E
E
E
E E
E E
E E
E E
C C
915mm 642mm 642mm 642mm 915mm
915mm
915mm
J
G
F F
F F
G
y
y
y
J
y
H
E
G
J
E
F
E
F
x
3.25 m
SIDE VIEW
3.89 m
2.03 m
TOP
VIEW
3.89 m 1.83 m
EXTENDED DRAGON
PERGOLA
ASSEMBLY INSTRUCTIONS
Toensurelongevity of your structureit is recommended that it is treated with a wood preservative on a yearly basis.
AFTERCARE
PLAN
EXTENDED DRAGON PERGOLA
(PKITDRGNAE)
GRANGE FENCING LIMITED
Halesfield 21, Telford TF7 4PA
Tel :[phone] Fax:[phone]
Email:[email protected] Web:www.grangefen.co.uk
OUT OF HOURS MESSAGE SERVICE: 01952 588088
JULY 2011 - ISSUE 2
ALL PRODUCTS ARE
MEASURED TO THE
HIGHEST AND WIDEST
POINT AND ALL SIZES
ARE APPROXIMATE
Grange Code: PKITDRGNAE
Extended Dragon Pergola Inst 8/7/11 10:47 Page 1

BEFORE YOU START
•Please ensure that you check all the component parts for quantity and quality before you
commence building the product. Report any missing parts immediately. The manufacturer will
not accept any responsibility for damaged items once any part of the product has been fitted or
altered in any way.
•Timber is a natural material and will react to varying levels of moisture content - ie. will swell or
shrink. All of the Timber components are pressure treated green. However, should extra
protection be required, they should be treated using a wood preservative treatment, following the
manufacturers instructions.
HEALTH AND SAFETY
Do N
NO OT Toverstretch when working from the step ladder.
In order to reduce the risk of suffocation please keep all plastic bags and small parts away from children.
•When you are ready to start, make sure you have the right tools to hand, plenty of space and a
clean, dry area for assembly.
It is advisable for two people to erect the structure.
PREPARATION
Make sure the area where the pergola is to be positioned is clear and ready for building the structure.
Thank you for choosing this garden structure from Grange Fencing Ltd. In order to gain the most
benefit from it please read the following instructions carefully.
RAFTERS D& C
SLOT TOGETHER
INTO THE TOP OF
POSTS A
TOOLS REQUIRED (Not Supplied)
POWER SCREWDRIVER
TAPE MEASURE
STEPLADDER
SPIRIT LEVEL
PARTS LIST
POSTS 4
POSTS 2
RAFTER (END) 2
RAFTER (SIDE) 4
CURVED BEAM (SHORT) 10
CURVED BEAM (LONG) 4
JOIST 1
ROUND FINIAL 2
CENTRE BLOCK 2
HARDWARE PACK
SCREW No.10 x 3” 12
SCREW 150 14
SCREW No.8 x 1.25” 56
SCREW No.10 x 4” 4
METAL ‘U’ CLIPS 14
ASSEMBLY INSTRUCTIONS
SITE PREPARATION
Mark out the area where the
structure is to be sited using the
footprint shown above.
Excavate a hole for each post to
a depth of 300mm (see fig.1)
This will give your structure
adequate stability.
ASSEMBLY
STEP 1
Site two of the Posts (A) at one
end of the proposed layout. Do
not fix in place at this time.
STEP 2
Take one of the Rafters (C) and
place into the top of each of the
posts. Ensure the cutouts in the
rafter align with those in the
posts.
STEP 3
Now site one of the Centre Posts
(B) and locate one of the Rafters
(D) into the slot in the end post
as fig.2.
STEP 4
The other end of the structure
should now be assembled
repeating Steps 1-3.
STEP 5
Complete the sides of the
structure by fitting the two
remaining Rafters (D) - fig.3.
STEP 6
Ensure the structure is level and
vertical. The posts may now be
fixed in place using the chosen
method.
(continued overleaf)
A
x
y
z
B
C
D
E
F
G
H
J
v
w
v
y
w
x
1.83 m
SITE PREPARATION
STEP 2
STEP 3
EXTENDED
DRAGON
PERGOLA
‘FOOTPRINT’
A
B
A
A
A
B
A
(fig.1)
1.83 m
300mm
A
B
A
CA
DA
(fig.2)
(fig.3)
D
D
D
C
STEPS 1-3
ASSEMBLES ONE
END RAFTER AND
ONE SIDE RAFTER
STEP 4
REPEATS THIS
ASSEMBLY FOR
THE OTHER END
STEP 5
COMPLETES THE
FRAME WITH THE
TWO REMAINING
RAFTERS
A
B
z
C
D
E
F
G
H
JWe would recommend that you use
MetCrete, fast set post fixing
concrete to fix your posts. Easy to
use, it sets in just 10 minutes.
C
Extended Dragon Pergola Inst 8/7/11 10:47 Page 2