Great Lakes SR Series User manual

19" EIA Wall Mount Swing Rack
Installation Instructions
1-866-TRY-GLCC (879-4522)
WeRackYourWorld.com
(UL609501 SR Series Equipment Rack)

PREFACE
This manual is provided to prevent service personnel from committing an act that
results in the risk of re, electric shock, or injury. Only trained service personnel
should receive, unpack, and assemble the SR Swing Rack. In addition, only
trained service personnel should install equipment in the swing rack.
SAFETY SYMBOLS USED IN THIS MANUAL
This manual provides general safety guidelines to be observed during
installation, operation, and maintenance of the SR Swing Rack.
WARNING: Failure to follow directions in the warning could result in injury to
persons or loss of life.
CAUTION: Failure to follow directions in the caution could result in damage to
equipment or storage data.
SAFETY CONSIDERATIONS
WARNING: Improper handling and use of the SR Swing Rack could result in
equipment damage, serious injury, or possible death.
Only UL® Listed ITE (Information Technology Equipment) units should be
installed inside the SR Swing Rack.
Be sure to read and follow all individual manufacturer equipment manuals for
safety and installation instructions.
Proper spacing is required when installing electrical equipment to avoid
electrical shock.
Maintain minimum spacing between the accessories and components and
the computer enclosure assembly for safe operation of the equipment when
installed in accordance with the National Electric Code ANSI/NFPA 70-1999.
The ambient temperature operating range for the SR Swing Rack and
accessories is +50 to +95°F (+10 to +35°C).
The non-operating temperature is -4 to +140°F (-20 to +60°C)
INSTALLATION
Loading Equipment
WARNING: Only install equipment after the SR Swing Rack has been properly
secured. Do not move the SR Swing Rack assembly while loaded.
2

MAXIMUM LOAD CAPACITY:
50 pound capacity for every size of SR Swing Rack
To maintain uniform distribution of the mechanical load in the SR Swing Rack,
load the heaviest equipment rst, at the bottom of the SR Swing Rack and load
the lighter units at the top.
SERVICE
The SR Swing Rack should be repaired by personnel trained by Great Lakes,
or returned to Great Lakes for repair or replacement. Contact Great Lakes
Technical Support at 814.734.7303 or at werackyourworld.com
WHAT’S INCLUDED
SR Swing rack
50 X 12-24 x ½" Philips pan head screws
This user’s manual
MOUNTING INSTRUCTIONS
Wood Studded Wall
Once the location on the wall has been determined, inspect the wall surface.
The wall must be at and square in the horizontal and vertical plane to ensure
the SR Swing Rack closes correctly. If the wall is not at and square, you might
be required to use shims.
Wood studded wall mounting instructions apply to a 2" x 4" wood stud wall with
3/4" plywood.
Recommended Mounting Hardware for Wood Studded Wall
Qty (4) 3/8 x 2" long Lag Bolts and 1" O.D. Flat Washer
Masonry Wall Surface
For masonry wall surface, the installed must provide all the appropriate
hardware.
3

4
19" EIA
Wall Mount Swing Rack
24SR, 36SR & 48SR
PART NO. H W D RMU
GL24SR 24.512" 20.562" 18.00" 12
GL36SR 36.763" 20.562" 18.00" 19
GL48SR 48.763" 20.562" 18.00" 26
GENERAL INFORMATION
The 24SR and 36SR frames are made of 14 Ga. Steel. All frames are
4"D with mounting front and rear.
Certications: UL Listed 2416 and UL 60950-1
Construction: Steel
Finish: Black Textured Powder Coat
Rail Type: Tapped #12-24 mounting holes, front and rear
When installing a Great Lakes Swing Rack or Wall Mount to materials such as
wood, cinder block, concrete, etc., please consider the load capacity within the
swing rack or wall mount structure, and be certain to check with local authorities to
determine the appropriate hardware requirements for these conditions. Because
wall compositions may vary at different installation sites, Great Lakes cannot
warrant the tness or suitability of any installation instructions or installation
hardware it may provide for swing rack or wall mount enclosures. Great Lakes
hereby DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, REGARDING THE SUFFICIENCY, FITNESS OR SUITABILITY OF ANY
INSTALLATION INSTRUCTIONS OR INSTALLATION HARDWARE GREAT LAKES
MAY PROVIDE FOR SWING RACKS AND WALL-MOUNTED ENCLOSURES.Great
Lakes recommends that an experienced maintenance and/or technical person
be consulted regarding the proper wall-mounting hardware and procedures to be
used for the anticipated load capacity of the swing rack or wall mounted enclosure.
Product specications are subject to change without prior notice.

PARTS LIST: 24SR, 36SR, 48SR
STEP 1
Place the back brace onto the four threaded studs on the two side brace as-
semblies. Secure with four #10-32 keps nuts. Tighten with 3/8" nut driver.
Install the top/bottom braces to the outside of the two side brace assemblies
with eight #10-32 x 1/4" Phillips Pan Head screws, but do not tighten screws.
The large formed edge of the top/bottom braces mount towards the rear and
the inside of the swing rack.
5
Top/Bottom Brace
(qty. 2)
Phillips Pan
Head Screws
#10-32 x 1/4"
long (qty. 8)
Side
Brace
Assembly
(qty. 2)
Phillips Pan Head Screw
#10-32 x 1/4" long Top/Bottom
Brace
Back Brace
(qty. 1)
Keps Nuts #10-32
threads (qty. 4)
COMPONENT QTY.
TOP AND BOTTOM BRACE 2
SWING FRAME ASSEMBLY 1
SIDE BRACE ASSEMBLY 2
REAR BRACE PANEL 1
#10-32 KEPS NUT WITH EXTERNAL TOOTH LOCK WASHER 4
#10-32 X 1/4" PHIL PAN HD SCREWS, TYPE 23, BLACK 8
#10-32 X 1/2" PHIL PAN HD SCREWS, TYPE 23, BLACK 50
1/4 - 20 X 3/4"L PHIL 82O FLAT HEAD SCREW W/NYLON LOCKING PELLET 2
BLACK NYLON SPACER (0.50 OD, 0.26 ID 0.187 TH) 2
INSTRUCTION MANUAL 1
TOOLS REQUIRED: 3/8" NUT DRIVER, PHILLIPS HEAD SCREWDRIVER
Special Note: Item #7 used to mount equipment to swing rack.

6
STEP 2
Mount the rear assembly to the wall with four lag screws (These are not
provided. The customer is to determine for type of wall). Mounting locations
are as shown.
Install the 19" EIA Swing Frame by retracting both pins. The pins can be locked
out for ease of assembly by retracting the outside pin into the slot provided.
The retractable pins are to be near the front of the Swing Frame when
installing.
Release the lower pin then, align the top pin to the top receptacle and release
pin. Place 1/4-20 Screw through the hole in bottom (opposite pin hinge).
Assemble spacer on exposed threads on inside of swing rack and close
Swing Frame. Tighten screw by screwing into pem nut in Swing Frame.
Repeat screw/spacer assembly for top. Finally, tighten 8 screws on the top
and bottom braces.
LEFT HAND ASSEMBLY SHOWN
Mounting
Dimensions
Receptacles for
Pivot Pins
1 in top, 1 in bottom
Retractable Pivot Pins (qty. 2)
19" Swing
Frame
Assembly
16.00" on
center
1/4 - 20 screw
1/4 - 20 screw
Part No. Height
GL24SR 18" on center
GL36SR 30" on center
GL48SR 42" on center

7
Secure retractable pins into receptacle (2 locations)
UNIVERSAL
The 19" EIA Swing Frame Rack can be hinged (retractable pin) on either side.
Customer needs to determine which side is to open. To open, simply retract
both pins (top and bottom) and then open the Swing Frame Rack similar to that
of a door.
LEFT HAND OR RIGHT HAND
CAUTION:
When installing 19" EIA equipment, make sure both retractable pins (2) are
secured into the rear section that has been mounted to the wall. Be sure
all screws, nuts, and mounting hardware are tightened before loading with
equipment.

FORM: #MS - 5.02-12, REV 5
ETSI Associate Member
Thank you
for your
business!