Green Brook HDP1800 User manual

INSTRUCTION MANUAL
HDP1800 AUTOMATIC HAND DRYER
TECHNICAL DATA
• Thank you for purchasing our HDP1800 Automatic Hand Dryer
• Please read this instruction manual carefully and keep for
future reference.
hould the power lead become damaged, it must only be replaced by the manufacturer, the manufacturer’s
customer service unit, or a similarly qualified specialist to avoid risk of injury.
Mains voltage : 230 /50Hz
Wattage : 1850W
afety class : II
Degree of protection : IPX1
Operation : Automatic operation (on/off) controlled
by electronic proximity sensor
Max. Uninterrupted operation : 1min
“stand-by” consumption : < 1W
Appliance conforms to :
GUARANTEE
The hand dryer is guaranteed for one year, from the date of purchase against faulty materials or
workmanship.
In the event of any part being found to be defective, the hand dryer will be repaired or at the
manufacturers option replaced, without charge, provided that the hand dryer;
a. Has been installed and used in accordance with the instruction given with each unit.
b. Has not been installed to an unsuitable electrical supply. (correct electricity supply
requirements is stated on the units rating label).
c. Has not been subjected to misuse, neglect or damage.
d. Has been properly serviced in accordance with the instructions given with each unit.
e. Has not been modified or repaired by any person not authorised by the manufacturer.
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
s a l e s @ g r e e n b r o o k . c o . u k
WWW.GR EENBR OOK.CO.UK
Figure 1
Figure 3
Figure 2
Issue no: 701498

IMPORTANT INFORMATION
USAGE
DESIGN AND OPERATION
MAINTENANCE
SERVICING THE HAND DRYER
MOUNTING INSTRUCTIONS
INSTALLATION OF THE UNIT
INSTALLATION INSTRUCTIONS
Please read the information contained in these instructions carefully. It provides important advice regarding
the safe installation, use and maintenance of the unit. These instructions should be kept in a safe place and
passed on to the new owner should the unit be resold.
The manufacturer will accept no liability or damage resulting from failure to observe the
following:
• Ensure packing materials are disposed of properly.
• Any damage to the hand-dryer on delivery should be reported to the supplier before the unit is
connected.
• To ensure the safe operation of the hand-dryer, it should only be installed and connected by a trained
electrician in accordance with the instructions contained in this booklet.
• The hand-dryer should only be used for the purpose for which it is intended.
• Repairs to the hand-dryer should only be carried out by a trained specialist.
Unit must be fixed to a solid supporting wall. Recommended fixing heights to top of unit are as follows:
a. 1.5 metres above floor for normal use.
b. 1.2 metres above floor where average age of user is below 16 years.
c. 1.0 distance above shelves, sinks or radiators.
To ensure ease of installation and subsequent maintenance the horizontal distance to any
adjacent wall should not be less than 2.0 metres.
AFTER IN TALLATION OR ERVICING, UNIT MU T BE CHECKED AND ONLY LEFT WHEN
ELECTRICALLY AND MECHANICALLY AFE.
hould the unit need to be opened at any time, ensure that it is disconnected first. The hand-dryer must
not be installed within range of people using the baths and/or showers.
Drill four holes with a diameter of 6mm where the unit is to be installed, according to the dimensioned
sketch in figure 1, and insert the rawl plugs enclosed. For mounting the hand-dryer, remove its casing; for
purpose, the 2screws in the lower area of the unit are to be removed (refer to figure 2). The casing can
then be lifted upwards and be taken off the mounting base (figure 3) (the black air exit grid remains
resting on the mounting base!). The unit can now be attached to the wall with the four screws enclosed
using the rawl plugs inserted earlier.
Please make sure that the wall is plain and the mounting base is not distorted when screwing on the unit-
ensure the plain fastening of the unit by using plain washers, if necessary!
After having mounted the hand-dryer, replace the casing. The best way to do this is to adjust the lower part
of the casing to the air exit grid and to the plate with the ventilating slits, then to the press it upwards at
the front edge until the upper part of the casing clicks into place at the mounting base. Please do not
forget to fasten the casing with the screws removed at the beginning!
Wire the unit into the nearby fused double pole switch. The hand dryer is now ready to use.
The hand-dryer is intended to be affixed to a vertical wall in industrial and commercial areas and to be
used exclusively for drying hands. The electrician should determine the suitability of area to fit.
The casing can, if necessary, be wiped with a damp cloth. Do not use any caustic or scouring nor solvent-
containing cleaning agents. It may be necessary to clean the two lenses of the proximity sensor at certain
intervals using a soft cloth.
The manual service period for the dryer should be every 3months or more frequent as dictates. Isolate the
unit from the electricity supply before servicing, remove dust, fluff and any other build up of foreign matter
from the inlet and outlet grille areas.
Always ensure that the installation conforms to the current edition of the wiring regulations, B 7671 (UK)
or the appropriate standards in your country.
Ensure that the unit is separately fused with a suitably rated fuse and that it is connected to the supply
with a double pole isolating switch having a contact separation of at least 3mm.
Care should be taken that single insulated conductors cannot come into contact with the mounting
surface.
The hand-dryer contains a heated fan which emits a diagonal jet of warm air downwards. The hand-dryer is
fitted with an infra-red sensor which automatically switched the unit on when hands approach the underside
of the unit. Once the hands have been removed, the fan automatically switches off after a short delay. The
hand-dryer does not, therefore, require an integrated power switch. erving as a safety measure, an automatic
time switch is integrated that switches off the unit after any uninterrupted operation of 1min-a short
movement within the sensor area will immediately switch on the hand-dryer, if required.
SAFETY PRECAUTIONS
1. Read all the instructions carefully before using the appliance.
2. Remove the packages and ensure that the appliance is undamaged.
In case of doubt do not use the appliance and contact your supplier.
3. Do not let children play with parts of the packages (such as plastic bags).
4. Do not install the automatic hand dryer on wooden or plastic walls.
5. Do not install the appliance within range of people using baths or showers.
6. Before installing the unit, check that the electrical voltage of your main
supply corresponds to the voltage marked on the rating label of the appliance.
7. Before installing the appliance, check that there are no obstructions within 50cm of the sensor.
8. Do not install in places where there are gas, paint or other inflammable objects.
In case of malfunction or abnormal operation, turn off, unplug it from the socket-outlet and send the
appliance to the service centre for repair and inspection.
9. Before maintenance or repair, make sure that the unit is unplugged.
10. Do not insert any objects into the appliance.
11. Prevent water from getting into the housing of the appliance during operation or in storage.
Hazard of electric shock, always store in dry area with no moisture.
12. Do not use outdoors
13. The appliance is not intended for use by young children or infirm persons without supervision.
14. Young children should be supervised to ensure that they do not play with the appliance.