Greenfire Greenfire GF55 User manual

FPI FIREPLACE PRODUCTS INTERNATIONAL, LTD. 6988 Venture St., Delta, BC, Canada V4G 1H4
GF55-919-571b 12.16.16
WARNING:
Improper installation, adjustment, alteration,
service or maintenance can cause
injury, property damage, or loss of life.
Refer to this manual. For assistance or
additional information consult an authorized
installer or service agency.
FOR YOUR SAFETY:
Do not store or use gasoline or other ammable
vapoursandliquidsinthevicinityofthisoranyother
appliance.
Installation and service must be performed by an
authorized installer or service agency.
Tested by:
IMPORTANT: SAVE THESE INSTRUCTIONS
Greenre® GF55 & GFI55
OWNER'S MANUAL
Freestanding and Fireplace
Insert Pellet Stove
GF55

Greenre Pellet Stove and Insert Owner's Manual
2
TO THE NEW OWNER
Congratulations! You are the owner of a state-of-the-art Pellet Stove.
Thank-you for purchasing a
FPI FIREPLACE PRODUCT.
The pride of workmanship that goes into each of our products will give you years of trouble-free
enjoyment. Should you have any questions about your product that are not covered in this manual,
please contact the GREENFIRE DEALER in your area.
Safety Note:                 
󰀩
about restrictions and installation inspection requirements in your area.
The authority having jurisdiction should be consulted before installation to determine the need to
obtain a permit.
Rates: This manual describes the installation and operation of the Regency GF55/GFI55 pellet heater.
This heater meets the 2015 U.S. Environmental Protection Agency’s wood emission limits for wood
emission limits sold after May 15, 2015. Under specific test condition this heater has been shown to
deliver heat at rates raging from
6500-40,000 Btu/hr
Efficiency: 78%
FIRE EXTINGUISHER AND SMOKE DETECTION: All home with a pellet burning stove should
have at least one fire extinguisher in a central location known to all the household. Smoke detectors
and carbon monoxide detectors should be installed maintained in the room containing the stove. If it
sounds the alarm, correct the cause but do not deactivate. You may choose to relocate the smoke the
smoke detection device within the room; DO NOT REMOVE THE SMOKE OR CARBON MONOXIDE
DETECTORS FROM THE ROOM.
WARNING: This wood heater needs periodic inspection and repair for proper operation. It is against
federal regulation to operate this wood heater in a manner inconsistent with operating instructions in this
manual.
WARNING: This wood heater has a manufacturer set minimum low burn rate that must not be altered.
It is against federal regulations to alter this setting or other wise operate this wood heater in a manner
inconsistent with operating instructions in this manual.

Greenre Pellet Stove and Insert Owner's Manual 3
TABLE OF CONTENTS
SAFETY LABEL
Copy of Serial No. Decal ...............................................4
INSTALLATION
Safety Warnings & Recommendations..........................5
Important Safety Information .........................................6
Pellet Quality .................................................................6
OPERATING INSTRUCTIONS
Control Board Functions................................................7
Automatic Safety Features ............................................7
Operating Your Pellet Stove ..........................................8
Manual Mode............................................................8
High / Low Mode.......................................................8
󰀨.........................................................8
Slider / Damper Set-Up .................................................9
Hopper Grate Installation...............................................9
MAINTENANCE
Routine Cleaning & Maintenance................................10
Opening the Door ...................................................10
Burn Pot & Liner .....................................................10
Door Glass Cleaning ..............................................10
Ash Pan & Door Gaskets........................................10
Ash Pan .................................................................. 11
Heat Exchanger Tubes........................................... 11
Fresh Air Intake ...................................................... 11
Exhaust Vent .......................................................... 11
Blower Mechanisms ............................................... 11
All Hinges................................................................ 11
Exhaust Passages..................................................12
Post Season Clean-Up...........................................12
Cleaning Plated Surfaces.......................................12
Firebox Panel .........................................................12
Replacing Door Glass.............................................12
WARRANTY
Warranty ......................................................................13
GF55

Greenre Pellet Stove and Insert Owner's Manual
4
INSTALLATION
SAFETY LABEL
This is a copy of the label that accom-
panies each GF55 & GFI55. We have
printed a copy of the contents here for
your reference.
On the GF55 the safety label is located
on the underside of the hopper lid.
On the GFI55 the safety label is located
on the hopper cover behind the top
faceplate.
To Prime Auger: Restart the unit five (5) minutes into its startup or by putting a small hand full of pellets into the burnpot.
To Operate Stove: MANUAL MODE: When a fire has been established the stove settings are adjustable. / HIGH/LOW MODE: (Requires a thermostat) When the
thermostat calls for heat the stove settings are adjustable. When the thermostat contacts open, the HEAT LEVEL and Fans will drop down to the LOW setting
until the thermostat contacts close again. / AUTO/OFF MODE: (Requires a thermostat) When the thermostat contacts close, the unit will light automatically.
Once up to temperature the stove settings are adjustable. When the thermostat contacts open, the stove will drop down to the LOW settings for 30 minutes. If
within the 30 min the thermostat contacts close, the HEAT LEVEL will return to previous MANUAL setting or if the thermostat contacts remain open the stove
begin its shutdown routine.
To Turn Off Stove: MANUAL and HI / LOW mode: Press the ON / OFF button
AUTO / OFF mode: Turn the thermostat down or off
The unit can be installed on a hard,
stable non-combustible surface.
L'appareil peut être installé sur une
surface non-combustible dure et stable.
Certified for use in Canada & USA
Certifié pour installation au
Canada et aux Etats-Unis.
Listed Room Heater, Pelletized Fuel Type (Appareil de chauffage à granules certifié)
Suitable For Mobile Home Installation (conçu pour être installédans une maison mobile) Tested to
(Testée selon):
UL 14 82 -19 98 / ULC S627-00 / ASTM 1509-95 / ULC S628-M93
US Environmental Protection Agency, certified to comply July 1, 1990, particulate emission
standards. (certifié conforme aux normes de l'US Environnemental Protection Agence du 1er juillet
1990, concernant les particules d'émission.)
This pellet appliance has been tested and listed for use in manufactured homes in accordance with Oregon
Administration Rules 814-23-900 through 814-23-909. Install and use only in accordance with the Manufacture’s
installation and operating instructions. Contact local building or fire officials about restrictions and installation inspection in
your area. Do not connect this unit to a chimney flue serving another appliance. See local building codes and
manufacturers instructions for precautions required for passing a chimney through a combustible wall or ceiling. Electrical
rating: 120 volts, 60 hz, 4.3 Amps. Route cord away from the heater.
Cet appareil a été testé et certifié pour être utilisédans les maisons mobiles en accord avec les "Règles Administratives
de l'Oregon 814-23-900 à 814-23-909". Installez et utilisez cet appareil seulement selon les consignes d'installation et
d'utilisation du fabricant. Contactez les autorités locales de votre région concernant les restrictions et les inspections
d'installation. Consultez les codes locaux dubâtiment et les instructions du fabricant concernant les précautions à
prendre lorsque une cheminée doit être installée àtravers un mur ou un plafond combustible. Alimentation électrique :
120 Volts, 60 Hz, 4.1 Amps. Placez le câble électrique loin de l'appareil.
For Use With Only Pelletized Wood fuels. Operate only with viewing door and ash removal door closed. Only replace
glass with ceramic glass. Components required for installation: a 3 inch (75 mm) or 4inch (100 mm) listed PL vent,
complete with components. Insert and Hearth mount installations; a listed single wall chimney liner may be used. Inspect
and clean Exhaust Venting system frequently.
Utilisation avec les combustibles sous forme de bois en granules uniquement. Utiliser seulement lorsque les portes avant
et la porte du réceptacle de cendre sont fermées. Si une ou des vitres doivent être remplacées, utilisez seulement du
verre céramique. Pièces requises pour l'installation du poêle : évacuation PL certifiéede 3 po (75mm)ou4 po (100mm)
avec ses composants. Installations du montage de l'encastrable et du foyer ; un conduit de cheminée à paroi simple
homologué peut être utilisé. Inspectez et nettoyez régulièrement le système d'évacuation.
Input Rating (débit calorifique): 12,000 to 45,000 BTU/Hr (3.5 to 13.2 kWh)
334
2009 2010 2011
CAUTION:
Hot while operating. Do not
touch, severe burns may
result. Keep children, clothing,
furniture, gasoline or other
flammable vapors away
.
ATTENTION:
Appareil chaud quand il fonctionne. Ne
pas toucher. Peut causer de graves
brûlures. Tenir hors de portée des enfants,
des vêtements, des meubles, de tout
carburant ou autre gaz inflammable.
DO NOT REMOVE THIS LABEL /
NE PAS RETIRER CETTE ÉTIQUETTE
See installation and operating instructions accompanying appliance. /
Consultez le manuel d’installation et d’utilisation de l'appareil
.
A Sidewall to Unit (De la paroi latérale à l'appareil)
8” (203 mm)
B� Top of unit to an unshielded 8” (203 mm) mantle
�(Du haut de l'appareil à un manteau de cheminée non blindé) 8” (203 mm)
C Unit to top facing (protruding ¾” [19 mm])
(
De l'uappareil au sommet du parement)
8” (203 mm)
D Unit to side facing (protruding ¾” [19 mm])
(
De l'appareil au parement latéral)
8” (203 mm)
E� From door opening of unit to edge of floor protection
�(De l'ouverture de la porte à l'avant de protection de plancher) 6” (152 mm)
F From side of unit to edge of floor protection (De l'ouverture
de la porte à l'avant de la protection de plancher) 6” (152 mm)
Combustible floors must be protected by a non-combustible material. - See Owners Manual.
Le plancher combustible doit être protégé par un matériel non combustible. - Consultez le
manual.
INSTALLED AS A FIREPLACE INSERT STOVE MODEL (GFI55) / À
INSTALLERCOMME UN POÊLE ENCASTRABLE (GFI55).
Minimum clearances to combustible materials./ Dégagements minimaux aux
matériaux combustibles :
A Sidewall to Unit (De la paroi latérale à l'appareil)
6” (152 mm)
B Backwall to Unit (De la paroi du fond à l'appareil) 3” (76 mm)
C� Corner to Unit (Du coin à l'appareil)
2” (51 mm)
D Wall to vent (Du mur au système d'évacuation) 3” (76 mm)
E� From door opening of unit to edge of floor protection
�6” (152 mm)
�
�
�
�
�
(De l'ouverture de la porte au devant de protection de
plancher) NOTE: A combustible floor must be protected by a
non-combustible material - Width 27" (686mm) by depth 34"
(864mm). (Un plancher combustible doit être protégépar un
matériau non combustible. 27 po de large (686 mm) x 34 po
de profond (864 mm).)
�Minimum Alcove Width (Largeur minimale de l'alcôve) 36” (914 mm)
�Minimum Alcove Height (Hauteur minimale de l'alcôve) 48” (1219 mm)
�Maximum Alcove Depth (Profondeur maximale de l'alcôve) 30” (762 mm)
INSTALLED AS A FREESTANDING STOVE MODEL (GF55) / À INSTALLERCOMME
UN POÊLE AUTOPORTANT, QU’IL SOIT ENCASTRÉ, SUR PIED OU DANS UNE
MAISON MOBILE.
Minimum clearances to combustible materials./ Dégagements minimaux
aux matériaux combustibles :
Serial No. / No. De Serié:
Greenfire GF55 (Stove) GFI55 (Insert)
Model / Modèle:
15956
B
A
D
C
Adjacent wall
FE
Floor Protection
A
B
C
E
Backwall
Sidewall
D
Pour démarrer le poêle: Appuyer sur le bouton "ON/OFF". Si le Auger nécessite d'être amorcé, appuyer sur le bouton manuel d'alimentation du Auger jusqu'à ce que les granules se déversent dans le pot de combustion.
Pour faire fonctionner le poêle : MODE MANUEL : Lorsque le feu est bien établi, les réglages peuvent être ajustés. / MODE "HIGH/LOW" : (Nécessite un thermostat) Lorsque le thermostat requière de la chaleur, les réglages peuvent être ajustés. Lorsque les contacts du
thermostat ouvrent, le réglage du niveau de chaleur et les ventilateurs s'ajusteront au réglage " bas " jusqu'à ce que les contacts du thermostat se referment. / MODE "AUTO/OFF" : (Nécessite un thermostat) Lorsque les contacts du thermostat ferment, le poêle s'allumera
automatiquement. Lorsque la température adéquate est atteinte, les réglages peuvent être ajustés. Lorsque les contacts du thermostat ouvrent, le poêle s'ajustera aux réglages "LOW" pendant 30 minutes. Si les contacts du thermostat sont fermés pendant ces 30
minutes, le réglage de niveau de chaleur retournera sur "MANUEL" ou si les contacts du thermostat restent ouverts, le poêle entamera le processus d'arrêt.
DATE OF MANUFACTURE /
DATE DE FABRICATION :
Pour éteindre le poêle : MODE MANUEL ET " HIGH/LOW " : Appuyer sur le bouton "ON/OFF".
Manufactured in Canada for /
Fabriqué dans le Canada pour:
FPI Fireplace Products International Ltd.
Delta, BC, Canada
Model BIH Only Minimum Clearance to Combustible Materials / Espace de
dégagement requis pour le modèle BIH:
G
B
H
BIH Model
E
FPI or BIH
Models
G� From
Sides and rear walls to standoffs
�(
Des parois latérales et arrière aux espaceurs
) 0” (0 mm)
H
Recess depth
(
Profondeur de la cavité
) 11” (280 mm)
FS Model
MODE "AUTO / OFF" : Régler le thermostat à la baisse ou l'éteindre.
GF55-081a
J F M A M J J A S O N D



Greenre Pellet Stove and Insert Owner's Manual 5
INSTALLATION
INSTALLATION
CAUTION:
Do not connect to any air distribution duct or system.
Do not burn garbage or ammable uids such as gasoline,
naptha or engine oil.
Unit hot while in operation. Keep children, clothing and fur-
niture away. Contact may cause skin burns.
FUEL: This pellet stove is designed and approved to only burn wood
󰀨
operation and performance of the unit and may void the warranty. Check
with your dealer for fuel recommendations.
THE USE OF CORDWOOD IS PROHIBITED BY LAW.
SOOT:󰀩
the formation of soot which will collect on the glass, the heat exchanger,
the exhaust vent system, and may stain the outside of the house. This is
󰀩
adjust the slider/damper as needed to ensure proper combustion. See
"Slider/Damper Setting".
CLEANING:
creosote in the exhaust. This will vary due to the ash content of the fuel
used and the operation of the stove. It is advisable to inspect and clean
the exhaust vent semi-annually or every two tons of pellets.
ASHES: Disposed ashes should be placed in a metal container with a tight
fitting lid. The closed container of ashes should be on a non-combustible
floor on the ground, well away from all combustible materials pending
final disposal. If the ashes are disposed of by burial in soil or otherwise
locally dispensed, they should be retained in the closed container until all
cinders have been thoroughly cooled.
ELECTRICAL: The use of a surge protected power bar is
recommended. The unit must be grounded. The grounded electrical
cord should be connected to a standard 115 volts (4.6 Amps), 60 hertz
electrical outlet. Be careful that the electrical cord is not trapped under
the appliance and that it is clear of any hot surfaces or sharp edges and
also must be accessible. If this power cord should become damaged, a
replacement power cord must be purchased from the manufacture or

520 watts.
GLASS: Do not abuse the glass by striking or slamming the door. Do not
attempt to operate the stove with broken glass. The stove uses ceramic
glass. Replacement glass must be purchased from an Greenfire dealer.
Do not attempt to open the door and clean the glass while the unit is in
operation or if glass is hot. To clean the glass, use a soft cotton cloth and
mild window cleaner, gas or wood stove glass cleaner, or take a damp
paper towel and dip into the fly ash. This is a very mild abrasive and will
not damage the glass.
FLAMMABLE LIQUIDS: Never use gasoline, gasoline-type lantern fuel,
kerosene, charcoal lighter fluid, or similar liquids to start or “freshen up”
a fire in the heater. Keep all such liquids well away from the heater while
it is in use.
SMOKE DETECTOR: Smoke detectors should be installed and
maintained in the structure when installing and operating a pellet burning
appliance.
OPERATION: The ash pan and door must be closed securely for proper
and safe operation of the pellet stove. Also ensure all gaskets on the door
are checked and replaced when necessary.
KEEP ASH PAN FREE OF RAW FUEL.
DO NOT PLACE UNBURNED OR NEW PELLET FUEL IN ASH PAN. A
FIRE IN THE ASH PAN MAY OCCUR.
INSTALLATION: Be sure to maintain the structural integrity of your
home when passing a vent through walls, ceilings, or roofs. It is
recommended that the unit be secured into its position in order to avoid
any displacement.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING
SYSTEM OF THIS UNIT.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING
ANOTHER APPLIANCE.
FRESH AIR: Outside Fresh Air connection is optional. Must be
connected to all units installed in Mobile and “Air Tight Homes” (R2000)
or where required by local codes. Consider all large air moving devices
when installing your unit and provide room air accordingly. Limited air
for combustion may result in poor performance, smoking and other side
effects of poor combustion.
If you have any questions with regards to your stove or the above-
mentioned information, please feel free to contact your local dealer for
further clarification and comments.
SINCEFPIHASNOCONTROLOVERTHEINSTALLATIONOFYOUR
STOVE,FPIGRANTSNOWARRANTYIMPLIEDORSTATEDFORTHE
INSTALLATIONORMAINTENANCEOFYOURSTOVE.THEREFORE,
FPI ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL
DAMAGE(S).
SAFETY WARNINGS & RECOMMENDATIONS

Greenre Pellet Stove and Insert Owner's Manual
6
INSTALLATION
INSTALLATION
PELLET QUALITY
Pellet quality is important, please read the following:
Pellet quality is a major factor in how the Pellet stove will operate.
If the pellets have a high moisture or ash content the fire will be
less efficient and has a higher possibility of the fire building up and
creating clinkers (hard ash build-up).
Your Greenfire Pellet Stove has been designed to burn wood
pellets only. Do not use any other type of fuel, as this will void any
warranties stated in this manual.
The performance of your pellet stove is greatly affected by the type
and quality of wood pellets being burned. As the heat output of
various quality wood pellets differs, so will the performance and
heat output of the pellet stove.
CAUTION: It is important to select and use only pellets that are dry
and free of dirt or any impurities such as high salt content. Dirty fuel will
adversely affect the operation and performance of the unit and will void
the warranty. The Pellet Fuel Industries (P.F.I.) has established standards
for wood pellet manufacturers. We recommend the use of pellets that
meet or exceed these standards. Ask your dealer for a recommended
pellet type.
P.F.I. PELLET STANDARDS:
Fines (fine particles)......1% maximum through a 1/8" screen
Bulk Density.................. 40 pound per cubic foot minimum
Size.............................. 1/4” - 5/16” diameter 1/2" - 1-1/2" long maximum
Ash Content ..................1% maximum (Premium grade)
..................3% maximum (Standard grade)
Moisture Content...........8% maximum
Heat Content.................approximately 8200 Btu per pound minimum
ASH: The ash content of the fuel and operation of your stove will directly
determine the frequency of cleaning. The use of high ash fuels may
result in the stove needing to be cleaned daily. A low ash fuel may allow
longer intervals between cleaning.
CLINKERING: Clinkers are silica (sand) or other impurities in the
fuel that will form a hard mass during the burning process. This hard
mass will block the air flow through the Burn Pot Liner and affect the
performance of the stove. Any fuel, even approved types, may tend to
clinker. Check the Burn-Pot Liner daily to ensure that the holes are not
blocked with clinkers. If they become blocked, remove the liner (when
the unit is cold) and clean/scrape the clinkers out. Clean the holes with
a small pointed object if required. Refer to the section Routine Cleaning
and Maintenance.
PELLET FEED RATES: Due to different fuel densities and sizes, pellet
feed rates may vary. This may require an adjustment to the slider damper
setting or to the auger feed trim setting on low.
Since FPI has no control over the quality of pellets that you use, we
assume no liability for negative results in selection of wood pellets.
Store pellets at least 36” (1 m) away from the pellet stove.
IMPORTANT SAFETYINFORMATION
Please read this entire Owner’s Manual before installation and op-
erating your Greenre Pellet Stove. Failure to follow these instruc-
tions may result in property damage, bodily injury or even death.
   󰀩    
information on installation restrictions and inspection requirements for
your area.


will be happy to assist you in obtaining information with regards to your
local building codes and installation restrictions.
Be sure to maintain the structural integrity of the home when passing
a vent through walls, ceilings, or roofs.

pressure and a slightly positive chimney pressure. It is very important
to ensure that the exhaust system be sealed and airtight. The ash pan
and viewing door must be locked securely for proper and safe opera-
tion of the pellet stove.
󰀩-
mended to ensure proper combustion air is admitted to the combustion
chamber. Setting the proper combustion air is achieved by adjusting
the slider damper located on the left side of the stove.
When installing the stove in a mobile home, it must be electrically grounded

the structural integrity of the home is maintained and all construction
meets local building codes.
Minor soot or creosote may accumulate when the stove is operated
under incorrect conditions such as an extremely rich burn (black tipped,

If you have any questions with regard to your stove or the above-men-
tioned information, please feel free to contact your local dealer for further


Greenre Pellet Stove and Insert Owner's Manual 7
OPERATION
OPERATING INSTRUCTIONS
1. AUGER LIGHT:
 
2. MODE LIGHT:
Responsible for signaling the state of the control board. When the light

has control of the unit. When the light is solid, the Heat Level Setting
can be altered.
3. THERMOSTAT SWITCH:
Used to set the unit’s controls to one of three mode settings; Manual,
󰀨
4. FEED RATE TRIM BUTTON:
Used to change the feed rate trims in ¼ second increments for all
feed settings. When this button is pressed, all the light will light up on
the Heat Output Indicator except for the one that shows the current
setting; the default setting is the number 4 light. To adjust the setting
hold the Feed Rate Trim button down and press the Heat Level up or
down buttons to adjust the setting.
5. COMBUSTION BLOWER TRIM BUTTON: Used to change the
Combustion Blower trims in 5 volt increments for all feed settings until
it reaches line voltage. When this button is pressed, all the light will
light up on the Heat Output Indicator except for the one that shows
the current setting; the default setting is the number 2 light. To adjust
the setting hold the Combustion Blower Trim button down and press
the Heat Level up or down buttons to adjust the setting.
6. ON/OFF BUTTON:
󰀨
7. ROOM AIR FAN ON/OFF BUTTON:
 󰀨
8. HEAT LEVEL ADJUSTMENT BUTTONS:
When pressed, will change the heat level setting of the unit up or down.
9. HEAT OUTPUT INDICATOR:
Shows the present heat output setting.
CONTROL BOARD FUNCTIONS
AUTOMATIC SAFETY FEATURES
A. The stove and insert have a low limit safety switch located on the housing of the exhaust blower. If the exhaust temperatures drop below 120°F
(49°C) the unit will shut down and will be required to go through a full start up procedure again.
The most common cause for this is an empty hopper. This switch should only be by-passed for testing purposes by a technician.
B. The stove and insert have a high limit safety switch located just below the hopper behind the external body panels. If the temperature of this
switch reaches 200°F (93°C), the auger will stop feeding fuel and as the exhaust temperatures drop below 120°F (49°C), the unit will shut
down.
The 200°F (93°C) switch is a manual reset and should only be reset by a service person who can first diagnose the reason for failure.
The two most likely causes are Convection Fan failure or High Limit Switch failure. Either one needs to be properly diagnosed and rectified.
Since this is a safety switch it should never be by-passed for any reason other than the service technician to test the operation.
Figure 3: Circuit Board Control Panel Decal.
GF55-094
ROOM AIR
FAN ON/OFF
HEAT LEVEL
AUTO/OFF
HIGH/LOW
MANUAL
AUGER
MODE
ON/OFF
FEED
TRIM
COMBUSTION
AIR TRIM
1
2
3
4
5
6
8
9
7
Starting a Fire in Your Pellet Stove

Greenre Pellet Stove and Insert Owner's Manual
8
OPERATION
OPERATING INSTRUCTIONS
OPERATING YOUR PELLET STOVE
PRE-BURN INSTRUCTIONS:The burn pot liner holes must be clear and the liner installed properly against the ignitor tube for proper
operation. Check the hopper for enough pellets to start the unit.
Note: The thermostat mode can be changed during normal operation.
DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN.
Figure 1: Thermostat Switch in
MANUAL position.
Figure 2: Thermostat Switch in
HIGH/LOW position.
Figure 3: Thermostat Switch in
ON/OFF position.
HIGH/LOW MODE: (Requires a thermostat)
INITIAL START-UP: See manual mode above.
OPERATION: When the thermostat calls for heat (contacts are closed) the stove settings are
adjustable as per Manual Mode. When the thermostat contacts open, the HEAT LEVEL and Fans
will drop down to the LOW setting until the thermostat contacts close again. *The LOW heat
setting can be adjusted for different fuel qualities (see “
”). The stove will come back to the previous HEAT LEVEL setting when the thermostat
contacts close again.
AUTO/OFF MODE: (Requires a thermostat)
INITIAL START-UP: See manual mode above.
OPERATION: When the thermostat contacts close, the unit will light automatically. Once up to
temperature, the stove operates the same as in MANUAL. When the thermostat contacts open, the
stove’s HEAT LEVEL and Fans will drop down to the LOW setting for 30 minutes. If the thermostat
contacts close within the 30 minutes, the HEAT LEVEL will return to the previous MANUAL setting.
If the thermostat contacts remain open the stove automatically begins its shutdown routine. The
ON / OFF button can be pressed at any time and the stove will immediately shut down. The stove
will re-light when the thermostat contacts close again.
TURNING YOUR PELLET STOVE OFF:
• MANUAL and HI / LOW mode: To turn the unit OFF, simply press the ON / OFF button. This will
stop the feed of pellets. The blowers will continue to operate and cool the stove down. When
cool enough, the stove will turn off.
• AUTO / OFF mode: To turn the unit OFF, turn the thermostat down or off. NOTE: The unit will run
on low for three (3) minutes before it turns off.
DO NOT unplug unit while Combustion fan is operating.
This may lead to smoke escaping from the stove.
MANUAL MODE:
All control of circuit board function is adjusted at the circuit board.
To START: Press the ON / OFF button. The stove will turn on. The system light will flash. The
Auger Light will flash with each pulse of the auger (the Auger Feed Rate is pre-programmed during
start-up). The Heat Level Indicator will show the Heat Level that the stove will run at after start-up
and can be adjusted but the change will not take affect until the start -up has finished.
To PRIME AUGER: If this is the first time the unit has been started or the unit has run out of fuel,
the auger will need to be primed. This can be done by restarting the unit five (5) minutes into its
start-up or by putting a small hand full of pellets into the burnpot.
To OPERATE: When a fire has been established, the System Light will turn solid (after approximately
10 - 15 minutes) and the Auger Light will continue to flash to the corresponding Heat Level setting.
The convection blower (room air blower) will turn on. The speed of this blower is controlled by the
setting of the heat level output indicator. The convection blower can be turned off by depressing the
room air on/off button. For the best efficiency and to prevent cycling the convection blower should
be left on at all times.
Starting a Fire in Your Pellet Stove

Greenre Pellet Stove and Insert Owner's Manual 9
OPERATION
OPERATING INSTRUCTIONS
SLIDER / DAMPER SET-UP
THE SLIDER /DAMPER MUST BE SET AT TIME OF INSTALLATION.
A Qualified Service Technician or Installer must set the Slider
Damper. This is used to regulate the airflow through the pellet stove. The
slider damper knob is located on the left cab side (see Figure 7).
Figure 7: Slider / Damper Knob.
If the fire should happen to go out and the heat output indicator has been
set on the lowest setting, the Slider Damper should be pushed in slightly,
decreasing the air in the firebox.

or there is a build up of clinkers, this would be a sign that the pellet quality
is poor, this requires more primary air, the slider damper must be pulled out

   󰀩  

 
(pull out) slightly.
 
(push in) slightly.
 

proper operation, refer to Figure 8.
The combustion exhaust blower is a variable speed blower controlled by
the heat output button. This blower will decrease the vacuum pressure
inside the stove and as the heat output button is turned down.
SPECIAL NOTES:
Pellet quality is a major factor in how the Pellet stove will operate. If the
pellets have a high moisture or ash content the fire will be less efficient
and has a higher possibility of the fire building up and creating clinkers
(hard ash build-up).
Figure 8: Ecient Flame.
NOTE:
Incorrect use of the Damper will cause malfunction and poor
results from your stove or insert.
If all of these steps are followed, there should be
no visible emissions.
Starting a Fire in Your Pellet Stove

Greenre Pellet Stove and Insert Owner's Manual
10
MAINTENANCE
MAINTENANCE
ROUTINE CLEANING & MAINTENANCE
The following list of components should be inspected and maintained
routinely to ensure that the appliance is operating at its optimum and
giving you excellent heat value:
2-3 Days / Weekly Semi-Annually or ² Tons of Fuel
Burn Pot & Liner Exhaust Vent
Ash Pan Fresh Air Intake Tube
Inside Firebox Blower Mechanisms
Door Glass Behind Firebox Liners
Heat Exchanger Tubes All Hinges
Ash Pan & Door Gaskets Post Season Clean-Up
Door Latch
TOOLS REQUIRED TO CLEAN UNIT
a) Torx T-20 Screwdriver
b) 5/16" Wrench or Socket
c) 1" Soft Paint Brush
d) Soft Cloth
 
BURN POT AND LINER
(2-3 days)
Cleaning of the burn pot and liner must only be done when stove is cold.
To remove the burn pot and burn pot liner, open the door using the door
handle provided (located on the right-hand side of the stove). Swing the

by gently lifting up the front of the burn pot, then sliding the assembly from

This is the ‘pot’ where the pellets are burned. Every two (2) to three (3)
days (when the unit is cold), remove the burn-pot liner from the stove and
Failure to keep the
liner clean may cause a build up of fuel past the burn pot liner and
up the drop tube. This will cause the auger to jam and may result in
pellets burning in the drop tube and hopper. Using a metal scraper,
remove material that has accumulated or is clogging the liner’s holes.
Then dispose of ashes from the liner and from inside the burn-pot. Place
the burn-pot back into the stove, making sure that the pipes are properly
            
seated in the locater holes. Place the liner back into the burn-pot, making
sure that the ignitor hole in the liner is aligned with the ignitor tube. Push
the liner up against the ignitor tube.
Figure 9: Burn Pot Assembly.
DOOR GLASS CLEANING
(2-3 days)
Cleaning of the glass must only be done when stove is cold. Open the
door by lifting the handle. The glass can be cleaned by wiping down the
outside and inside of the glass with a dry soft cloth.
If the glass has build up that can not be removed with only the cloth, clean
the glass using paper towel and a gas appliance glass cleaner, this may
be purchased through most dealers. If a gas appliance glass cleaner is

After the glass has been cleaned use the dry soft cloth to wiping down the
outside and inside of the glass.
ASH PAN AND DOOR GASKETS
(weekly)
After extended use the gasketing may come loose. To repair this, glue the


an airtight assembly.
OPENING THE DOOR
The door lever can be found behind the right side of the door frame. To
open the door, pivet the lever outwards and upwards until it unlocks.

the burn pot or there is a build up of clinkers, this is an indication that
the pellet fuel quality is poor or the stove may need cleaning. Check the
stove for ash build up (clean if required) and adjust the slider / damper to
produce the proper clean combustion.
Starting a Fire in Your Pellet Stove