Greenheck PVF User manual

Installation, Operation and Maintenance Manual
Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure
to comply with instructions could result in personal injury and/or property damage!
Indirect Gas-Fired Heat Modules 1
General Safety Information
These indirect gas-fired furnaces are commonly used
in many different manufacturer’s ventilating products.
For unit-specific information, refer to the Installation,
Operation and Maintenance manual (IOM) for the unit in
which this furnace is installed.
• Both the furnace units are listed for installation in the
United States and in Canada.
• Installation of gas-fired duct furnaces must conform
with local building codes. In the absence of local
building codes, installation must conform to the
National Fuel Gas code, ANSI Z223.1 or in Canada,
CAN/CGA-B149 Installation codes.
• All electrical wiring must be in accordance with the
regulations of the National Electric Code, ANSI/
NFPA-70.
• Unit is approved for installation downstream from
refrigeration units. In these conditions, condensate
could form in the duct furnace and provision must be
made to dispose of the condensate.
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Do not touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
FOR YOUR SAFETY
The use and storage of gasoline or other
flammable vapors and liquids in open
containers in the vicinity of this appliance is
hazardous.
WARNING
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
death. Read the installation, operating and
maintenance instructions thoroughly before
installing or servicing this equipment.
Recognized Component
®
®
Document 474645
Model PVF and PVG
Indirect Gas-Fired Heat Modules
Model PVF
Model PVG

Indirect Gas-Fired Heat Modules2
Burner Control Turndown
Burner turndown ratio is used in many places and must
be calculated. On the data label, locate the INPUT
BTU/HR (the largest number on the label) and also
the MINIMUM INPUT BTU/HR. Calculate the burner
turndown ratio and record it.
Burner Turndown: _______________
NOTE
This unit is an indirect gas-fired heat module that will
be referred to in this manual as a furnace.
Receiving
Since this furnace is already installed in a ventilation
unit, follow the Receiving Instructions for the unit which
are provided in the unit-specific Installation, Operating
and Maintenance manual (IOM).
Unpacking
If unit is to be installed, tested and operated right
away, locate and remove all packing materials from the
furnace, including any protective coverings that may
be on the combustion air intake and on the furnace
exhaust. Follow Unpacking Instructions as found in the
unit-specific IOM.
Storage
If unit must be stored after it is received, follow the unit-
specific storage instructions found in the unit IOM. Also
plug all piping.
Unit Identification
It is necessary to know the unit model number, the
burner control turndown and the serial number. This
information is needed when ordering replacement parts
and is available on labels located on the unit.
Furnace Model Number
On the furnace access door or immediately next to the
door is a Mylar data label. See image below. Locate the
furnace model number at the top of the label and record
it here:
Furnace Model Number: _____________________
Typical Unit ID Plate
Furnace Serial Number
The furnaces are assigned the same serial number
as the main ventilating unit. On the main unit control
access door is a stamped metal plate identifying the
unit serial number. Record that information here.
Furnace/Unit Serial Number: _____________________
ETL Listing
Model PVF and PVG furnaces have been ETL tested
as gas-fired heat modules intended for installation as a
component within heating equipment in duct or cabinet
mounted applications. They are ETL Recognized
Components.
INPUT BTU/HR =Burner Control
Turndown Ratio
MINIMUM BTU/HR
Example: 150,000 =2
75,000
The turndown ratio is 2:1 in this example.
Model
Number
Minimum Input
BTU/HR
Input
BTU/HR
Typical Furnace Data Label
Heat
Exchangers
Collector
Box
Combustion
Blower
Burner
Assembly
Product Overview
®

Indirect Gas-Fired Heat Modules 3
Table of Contents
General Safety Information .................... 1
Receiving, Unpacking, Storage ................. 2
Unit Identification ............................ 2
Furnace Model Number ....................... 2
Burner Control Turndown ..................... 2
Furnace Serial Number ....................... 2
ETL Listing ................................. 2
Product Overview............................ 2
Furnace Control Center
Furnace Control Center Components .......... 4
Typical Furnace Control Logic ................ 4
Typical Furnace, Electrical and
Control Components. . . . . . . . . . . . . . . . . . . . . . . 5
Gas-Fired Burner Turndown ................. 6
Electronic Modulation ....................... 6
Two Stage Valve............................ 6
Combinations.............................. 6
Available Turndown Control Options .......... 6
Installation of Venting for Outdoor Units ...... 7
Installation of Venting for Indoor Units ........ 7
Venting Methods ........................... 8
Installation of Standard Indoor Venting
Horizontal ................................. 8
Vertical ................................... 8
Installation of Concentric Venting
Horizontal ...............................9-10
Vertical ................................10-11
Two-Pipe Venting - Horizontal .............11-12
Two-Pipe Venting - Vertical .................. 12
Installation of Control Wiring ............... 13
Installation of Discharge Air Sensor ......... 13
Installation of Gas Piping.................13-14
Gas Supply Requirements. . . . . . . . . . . . . . . . . . . 14
Connect the Supply Gas Line ................ 14
Installation Addition Regulator ............... 14
Testing the System for Leaks ................ 14
Gas Pressure Test Ports .................... 14
Sequence of Operation..................... 15
Start-Up / Standby ........................ 15
Heat Mode ............................... 15
Recovery from Lockout..................... 15
Performance Data......................... 15
Gas Valves................................ 16
Start-Up - Furnaces (all units)............... 17
4:1 Turndown Electronic Modulation .......... 17
Adjust High Fire and Low Fire Settings ....... 18
Modulating Valve High Fire Setting .......... 18
Modulating Valve Low Fire Setting .......... 18
2:1 Turndown Electronic Modulation .......... 19
8 Stage Combustion ....................... 20
Single Stage.............................. 20
2 Stage Combustion ....................... 21
Combination Turndown Configurations ........ 21
Troubleshooting
Ignition Controller ......................... 22
4:1 Electronic Modulation .................23-24
2:1 Electronic Modulation ................... 25
8 Stage ................................26-27
Single and Two Stage ...................... 28
Reference: FX Controller ................... 29
Stand-alone Furnace Control ................ 29
Program Mode .......................... 29
Inlet Air Sensor (optional) .................. 29
Discharge Air Temperature................. 29
Outside Air Temperature................... 30
Go to High Fire Mode ..................... 30
Return to Normal Operation................ 30
Access to Set Points Menu ................ 30
Access the Discharge Air Temperature ....... 30
Access the Inlet Air Sensor (optional) ........ 30
Access the Room Override Setting .......... 30
Furnace Control with Microprocessor .......30-31
Maintenance
Combustion Blower Motor .................. 31
Burners and Orifices ....................... 31
Heat Exchanger ........................... 31
Flue Collector Box ......................... 31
Electrical Wiring........................... 31
Gas Train ................................ 31
Replacement Parts ........................ 31
Maintenance Log ....................Backcover
Our Commitment ....................Backcover
®

Indirect Gas-Fired Heat Modules4
Furnace Control Center
Each ventilating unit containing a furnace or a pair of
furnaces will have a furnace control center located on
the furnace vest plate. The control center receives high
voltage AC from the main unit control center and in
most cases, also receives low voltage control signals
(call for heat) from the main unit control center. In all
cases, see the unit-specific wiring schematic located
inside the main control center door.
1. Microprocessor (if present) senses low temperature
on temperature sensor, sends 10 VDC signal to
signal input converter.
2. Input converter changes analog signal to a form that
can be read by the FX controller and sends the signal
to the FX controller (call for heat).
3. FX controller receives call for heat, activates
modulating valve and the ignition controller.
4. Ignition controller receives call for heat from FX
controller, sends spark to igniter and activates the
combination valve. It looks for verification that the
combustion blower is running.
5. Flame sensor detects flame and ignition controller
shuts off igniter.
Typical Furnace Control Logic
In all cases, refer to the unit-specific wiring diagram
located on the unit control center door.
This illustration is only for a typical 4:1 turndown
electronic modulation configuration
Temperature Sensor
If there is no DDC, the sensor
is connected to the FX.
DDC
Located in
unit main
control center
FX Controller
Input Converter
Ignition
Controller
Call for heat
Activates and modulates
Modulating Valve
Activates
Ignition Controller
Activates
Combustion Blower
Spark to Igniter
Activates
Combination Valve
JOHNSON
CONTROLS
Controls Speed
of Combustion
Blower
(optional)
(optional)
Furnace Control Center Components
(Components and their locations will vary.)
Components shown are for a typical 4:1 turndown
electronic modulation configuration.
High Voltage Side
1. Power Distribution Block
2. Inducer Relay (controls combustion fan)
3. Combustion Blower
Low Voltage Side
4. Input Converter
5. FX Controller (modulates heat and switches entire
unit on/off
6. Spark Generator (also has high voltage present)
6a. Spark Igniter
7. 24 volt Terminal Strip
Control Sensors
8. High Temperature Sensor (auto reset)
9. Airflow Switches
10. Flame Sensor
Gas Train
11. Combination Valve
12. Modulating Valve
13. Burner Manifold
14. Collector Box
14
1
2
3
4
5
6
6a
7
8
9
10
11
12
13
®

Indirect Gas-Fired Heat Modules 5
Airflow Switch
Airflow switches are used on both
furnaces and are found on the furnace
vest plate. If the combustion blower
is multi-speed, there will be two of
them and each will switch in response
to a different pressure. The switch is
connected to the combustion blower
by means of a vacuum tube and is used to sense
operation of the combustion blower. The internal switch
is Normally Open (NO). If the blower fails to operate, the
open circuit will cause the ignition controller to disable
the furnace.
Flame Igniter
The igniter receives a high voltage
input from the ignition controller to
produce a spark between the two
electrodes. It operates only during
the ignition phase. On split burner
manifolds, there will be two igniters.
Flame Sensor
The flame sensor is identical to the flame igniter. It is
located on the opposite end of the burner manifold from
the igniter.
Auto Reset High Temperature Limit
Switch
This limit switch is installed through the
vest plate into the supply air plenum.
A350 and S350 Control System
Used on two stage and single stage
controls. Used in
conjunction with a
field-installed remote
temperature sensor.
Has an LED indicator
light to show when
the output relay is
energized. When used
with multiple stages,
the S350 controller is
used for the extra stages.
1092 Control System
Used on 2:1 electronic modulating controls. The A1092
control system consists of an amplifier, a remote
temperature dial and a remote temperature sensor.
The amplifier and remote temperature dial are factory-
installed on the vest plate while the remote temperature
sensor must be field-installed. The temperature dial and
amplifier are installed in the furnace control center. Field
adjustments include discharge air temperature, which is
done by means of the Remote Temperature Dial.
Amplifier
Remote
Temperature Dial
Typical Furnace, Electrical and
Control Components
Microprocessor
The microprocessor provides
the call for heat to the ignition
controller and also monitors
the discharge air temperature.
It is found only in the unit main
control center. On units with
electronic modulation, it also determines the required
burner firing rate.
Discharge Air Temp Sensor
This sensor is shipped with all
units and must be field-installed in
the discharge air duct. This may
be located in the main unit control
center or the furnace control center
depending on the control type.
Input Converter
The input converter takes
an analog signal from a
microprocessor or a BMS
and converts it to a control
signal that can be used
by the FX programmable
controller. It is found in the
furnace control center.
FX Programmable Controller
Used on all 4:1 electronic
modulating controls and
8:1 staged turndown.
The FX controller turns on and
electronically modulates gas
valves. It will also enable the
ignition module. The FX controller has a digital readout
and four push buttons, one for Function, one for Enter
and two for scrolling up or down. It is pre-programmed
at the factory for each specific furnace configuration
and it may be used to control two furnaces at the same
time.
Ignition Controller
This controller is found only in
the furnace control center. It
has an LED indicator light on
the top right of the controller
that will flash GREEN for
normal operation or RED for an error. Some furnace
configurations have two of these controllers.
Burner Manifold
Single Section
Burner Manifold
Split Burner
Manifold
S350 Controller
A350 Controller
®

Indirect Gas-Fired Heat Modules6
Gas-Fired Burner Turndown
Furnaces are available in single stage, multi-stage or
electronically modulated configurations. In single stage,
the entire furnace is either on or off. In multi-stage
furnaces, combustion occurs in stages and is expressed
as the number of different stages (example: 8 stage).
Electronically modulated furnaces have continuously
variable firing rates. In both staged and electronically
modulated furnaces, the result is burner turndown.
Turndown is the capability of the furnace to operate
at less than full capacity, accomplished by reducing
the amount of gas flow when the unit is operating. The
advantage in being able to turn down firing rate is that
when the demand for heat is low, the furnace will not
cycle as often. Turndown is expressed as a ratio and
is found by dividing the maximum BTU input by the
minimum BTU input.
Electronic Modulation
Turndown is specified by the customer. Most common
is the use of an electronically-controlled gas valve which
provides a 4:1 turndown. The entire furnace is sized
appropriately for the maximum heat
output ordered by the customer,
but it can operate as low as 25%
of its maximum capacity. The
electronically-controlled gas valve
will modulate the combustion rate
continuously, dependent on the
output from an FX controller. With
this method, all the burners fire
at the same time but at a varying
capacity. The Modulating Valve is used in conjunction
with an FX electronic controller and a combination valve
which provides an ON/OFF function.
Two Stage Valve
The two-stage valve is switched electrically from closed
to full output to half output, producing a 2:1 turndown.
In some cases, multiple furnaces may be used in a
ventilating unit. When this is done with two single-stage
furnaces, it is possible to run just one furnace at a time,
resulting in a 2:1 turndown.
If each furnace is already
configured for a 2:1 turndown,
the overall result can then be a
4:1 turndown.
Combinations
Various combinations of the methods outlined may be
used to accomplish the turndown requested by the
customer.
Available turndown control options include:
Electronic Modulation
Single Furnace
Unit
4:1 uses modulating valve and FX
programmable controller
2:1 uses modulating valve and
1092 control system
Two Furnace
Unit
8:1 uses one 4:1 modulating furnace with
FX controller and one 2 stage furnace
4:1 uses two 4:1 modulating furnaces
running in parallel
Staged
Single Furnace
Unit
8 stage
2 stage
1 stage
Two Furnace
Unit
16 stage uses one 8 stage furnace and
one single-stage furnace
4 stage uses two 2 stage furnaces
2 stage uses two single-stage furnaces
®

Indirect Gas-Fired Heat Modules 7
Installation of Venting for
Outdoor Units
Follow Guidelines
All of the following guidelines must be followed when
installing the unit.
WARNING
Do not install units in locations where flue products
can be drawn into adjacent building openings such
as windows, fresh air intakes, etc. Distance from
vent terminal to adjacent public walkways, adjacent
buildings, operable windows and building openings
shall conform with the local codes. In the absence
of local codes, installation shall conform with the
National Fuel Gas Code, ANSI Z223.1 or the Canadian
CAN/CGA B-149 Installation Codes.
WARNING
The following guidelines must be followed for all
outdoor units:
1. Building materials that will be affected by flue
gases should be protected.
2. Maintain minimum horizontal clearance of 4
feet from electric meters, gas meters, regulators
and relief equipment. In Canada, the minimum
clearance is 6 feet.
3. The combustion blower discharge on outdoor
units must be located a minimum of 42 inches
from any combustible materials.
4. Do not modify or obstruct the combustion air inlet
cover or the combustion blower weatherhood.
5. Do not add vents other than those supplied by the
manufacturer.
6. During the winter, keep the unit clear of snow to
prevent any blockage of the combustion venting.
Install Stack (optional)
Clearance may require an exhaust stack. Install an
exhaust stack as needed to the exhaust connection on
the unit. Install a vent terminator on the exhaust pipe.
Exhaust transition and vent termination must be
purchased from the factory for proper operation.
Exhaust pipe is by others.
WARNING
The following guidelines must be followed for all indoor
units:
1. Installation of venting must conform with local
building codes. In the absence of local codes,
installation must conform with the National Fuel
Gas Code, ANSI Z223.1 or in Canada, CAN/
CGA-B149 installations codes.
2. For the exhaust pipe, use pipe approved for a
Category III appliance or single wall, 26 gauge or
heavier galvanized vent pipe. The piping is required
to be gas-tight by ANSI.
3. For the combustion air pipe on separated
combustion units, sealed single-wall galvanized air
pipe is recommended.
4. The joints must be sealed with a metallic tape or
Silastic™ suitable for temperatures up to 350°F.
5. A minimum of 12 inches of straight vent pipe is
recommended after the exhaust connection and
before any elbows.
6. Vertical combustion air pipes should be fitted with
a tee, drip leg and clean-out cap to prevent any
moisture in the combustion air pipe from entering
the unit.
7. To reduce condensation, insulate any vent runs
greater than 5 feet.
8. All vent pipe connections should be made with at
least three corrosion-resistant sheet metal screws.
9. Refer to the National Fuel Gas Code for additional
piping guidelines.
NOTE
Vent piping is supplied by others and not supplied by
manufacturer.
NOTE
The drip leg should be cleaned out periodically during
the heating season.
NOTE
Clearances from combustible material for indoor units
are determined by the National Fuel Gas Code and/or
other local codes.
Installation of Venting for
Indoor Units
®

Indirect Gas-Fired Heat Modules8
Venting Methods
There are three venting methods for indoor mounted
units. For each method, the units can be vented
horizontally through an exterior wall or vertically
through the roof. Specific venting instructions are
provided for each method and shown in the following
pages. Construct the vent system as shown in these
instructions. Refer to your unit specific submittal to
determine the applicable venting option.
The venting method options are:
Standard Indoor Venting
• uses building air for combustion
• vents exhaust to outdoors
• one exterior roof or wall penetration
Separated Combustion Concentric Venting
• uses outside air for combustion
• vents exhaust to outdoors
• one exterior roof or wall penetration
Separated Combustion 2-Pipe Venting
• uses outside air for combustion
• vents exhaust to outdoors
• two exterior roof or wall penetrations
NOTE
For each method, the units can be vented horizontally
through an exterior wall or vertically through the roof.
Refer to the specific venting instructions for your
unit. Construct the vent system as shown in these
instructions.
Installation of Standard Indoor
Venting
Standard indoor venting uses one penetration through
an exterior wall or roof for venting the flue exhaust.
The combustion air is supplied from the air inside the
building. Units must not be installed in a potentially
explosive, flammable, or corrosive atmosphere. To
prevent premature heat exchanger failure, do not locate
unit where chlorinated, halogenated or acid vapors are
present.
When units are installed in tightly sealed buildings,
provisions should be made to supply an adequate
amount of infiltration air from the outside. The rule of
thumb is that an opening of one square inch should be
provided for every 1000 BTUs per hour of input rating.
Vent terminals must be used. Construct the vent
system as shown in the drawings. Reference the Vent
Pipe Diameter table and Exhaust Vent Pipe table for
additional details.
Installing Exhaust Vent Pipe
Install the vent pipe with a minimum downward slope
(from the unit) of 1/4-inch per foot (horizontal venting
only). Securely suspend the pipe from overhead
structures at points no greater than 3 feet apart.
The minimum vent length is 5 feet for horizontal and
10feet for vertical. The maximum vent length is 70 feet.
The total equivalent vent length must include elbows.
The equivalent length of a
4 inch elbow is 6feet and
the equivalent length of a
6inch elbow is 10 feet.
Attach the vent terminal
to the end of the exhaust pipe.
Vent Pipe Diameter
Select the vent pipe
diameter. Use only the
specified pipe diameter.
Standard Indoor Venting - Vertical
Standard Indoor Venting - Horizontal
Vent
Length
Minimum
(feet)
Maximum
(feet)
Horizontal 5 70
Vertical 10 70
Furnace Size
(MBH)
Exhaust Pipe
Diameter (inches)
75-175 4
200-400 6
A = 12 inch minimum
Air Inlet
A
Exterior
Wall
Exhaust
Vent
Terminal
Pitch vent pipe
downward
from furnace
¼ inch per foot
EXHAUST
AA
Exhaust Vent
Terminal
EXHAUST
A = 12 inch minimum
B = 12 inch minimum,
but should size
according to expected
snow depth
Air Inlet
B
Roof Line
®

Indirect Gas-Fired Heat Modules 9
Concentric Venting – Horizontal
Refer to the diagram below for venting on horizontal
concentric systems. Maintain at least 12 inches from
the combustion air inlet guard to the exhaust vent
terminal (Dim. B). To prevent water from running into the
combustion air pipe and to allow for easy installation
of the combustion air inlet guard, the combustion air
pipe must terminate at least 2 inches from the exterior
surface of the outside wall (Dim. A).
Vent Connection Diameter
Vent terminals must be used (one vent terminal included
with each furnace). Construct the vent system as shown
in the drawings and refer to the table for the correct vent
connection diameters.
Vent Length
Refer to table for minimum and maximum vent lengths.
The total equivalent vent length must include elbows.
The equivalent length of a
4 inch elbow is 6feet and
the equivalent length of a
6inch elbow is 10feet.
Determine Venting
Location
Determine the location of the concentric venting adapter
(CVA) based on any clearances that must be maintained
(follow all codes applicable).
Attach Mounting Brackets
Attach field-supplied, corrosion-resistant, mounting
brackets to the CVA using corrosion-resistant sheet
metal screws.
Vent
Length
Minimum
(feet)
Maximum
(feet)
Horizontal 5 70
Non-Concentric Vent
Connection Diameter
Concentric Vent
Connection Diameter
Furnace Size
(MBH)
Exhaust
(inches)
Combustion Air
(inches)
Exhaust
(inches)
Combustion Air
(inches)
75-175 4446
200-400 6668
NOTE
Vent piping is supplied by others and not supplied by
manufacturer.
Installation of Concentric Venting
Concentric venting allows the exhaust pipe and
combustion air pipe to pass through a single hole in the
roof or wall of the building. A concentric venting adapter
(CVA) is required for concentric venting.
The concentric venting adapter is designed for indoor
installations and should never be installed on the
exterior of the building.
The exhaust pipe must terminate with the vent terminal.
For horizontal venting, the combustion air pipe must
terminate with the combustion air guard. For vertical
venting, the combustion air pipe must terminate with
the inlet terminal. Depending on what was ordered, one
of these vent terminals will be provided in the optional
venting kit along with the concentric venting adapter
(CVA).
If venting vertically through the roof, refer to the vertical
concentric venting instructions. If venting horizontally
through the wall, refer to the horizontal concentric
venting instructions.
CVA-4
4-inch Concentric
Venting Adapter
CVA-6
6-inch Concentric
Venting Adapter
Top View
Exhaust Connection
Concentric Side
Combustion Air Connection
Concentric Side
Exhaust Connection
Non-Concentric Side
Combustion Air Connection
Non-Concentric Side
CVA
A = 2 inch minimum
B = 12 inch minimum
Pitch vent pipe
downward
from furnace
1/4 inch per foot
Mounting
Bracket
Mounting
Bracket
Exhaust
Vent
Terminal
EXHAUST
COMBUSTION AIR
Exterior
Wall
BA
Combustion
Air Inlet Guard
®

Indirect Gas-Fired Heat Modules10
Install Exhaust Pipe
Slide the exhaust pipe through the CVA. Provide enough
exhaust piping to pass through the wall (or floor) and
provide the minimum clearance of 12inches between
the exhaust pipe termination and the combustion air
intake. With all required clearances satisfied, attach the
exhaust pipe to the CVA.
Install Combustion Air Pipe
Attach a field-supplied combustion air pipe to the
concentric side of the CVA.
Be sure to provide enough combustion air piping
to pass through the wall and provide the minimum
clearance of 2 inches between the combustion air intake
and the exterior surface of the outside wall.
Be sure to maintain the minimum clearance of
12inches between the exhaust pipe termination and the
combustion air intake.
Install CVA Assembly
Place the CVA assembly through the wall and verify
that all minimum clearance requirements as specified
in these instructions are met. Secure the CVA assembly
to the wall with corrosion-resistant sheet metal screws
through the mounting brackets.
Attach CVA Assembly to Unit
Attach the exhaust pipe to the unit’s combustion
exhaust. Using an additional combustion air pipe,
connect the unit’s combustion air supply intake to the
combustion air connection on the CVA.
Install Combustion Air Inlet Guard and
Exhaust Vent Terminal
Slide the combustion air inlet guard over the exhaust
pipe and fasten it to the combustion air pipe. Attach
the exhaust vent terminal to the discharge end of the
exhaust piping on the outside of the building.
Seal Opening
Seal the opening between the wall and the air intake
pipe using an appropriate method.
Concentric Venting – Vertical
Refer to the diagram below for venting on vertical
concentric systems. Maintain at least 12 inches
between the top of the combustion air inlet terminals
and the bottom of the exhaust terminal. (Dim. B).
The bottom of the combustion air intake pipe must
terminate above the snow line or at least 12 inches
above the roof, whichever is greater.
A tee with clean-out must be provided on the
combustion air and exhaust pipe to prevent debris from
entering the heat exchanger.
Vent Length
Refer to table. The total equivalent vent length must
include elbows. The
equivalent length of a
4inch elbow is 6feet and
the equivalent length of a
6inch elbow is 10feet.
Determine Venting Location
Determine the location of the concentric venting adapter
(CVA) based on any clearances that must be maintained
(follow all codes referenced in these instructions).
Attach Mounting Brackets
Attach field-supplied corrosion-resistant mounting
brackets to the CVA using corrosion resistant sheet
metal screws.
Vent Connection Diameter
Vent terminals must be used. Construct the vent system
as shown in the drawings and refer to the table for the
correct vent connection diameters.
Vent
Length
Minimum
(feet)
Maximum
(feet)
Vertical 10 70
A = 12 inch minimum, but
should size according to
expected snow depth
B = 12 inch minimum
C = 12 inch minimum
Roof Line
Exhaust Vent
Terminal
EXHAUST
COMBUSTION AIR
Combustion Air
Inlet Terminal
Mounting
Bracket
Tee with
drip leg and
clean-out cap
Mounting
Bracket
C
C
B
A
Non-Concentric Vent
Connection Diameter
Concentric Vent
Connection Diameter
Furnace Size
(MBH)
Exhaust
(inches)
Combustion Air
(inches)
Exhaust
(inches)
Combustion Air
(inches)
75-175 4446
200-400 6668
®

Indirect Gas-Fired Heat Modules 11
Installation of Two Pipe Venting –
Horizontal
Refer to the diagram below for venting on horizontal
concentric systems. Maintain at least 12 inches of
clearance between the exhaust pipe termination and the
exterior surface of the exterior wall (Dim. A).
The combustion air pipe must be a minimum of
12inches from the exhaust pipe and 24 inches from the
exterior surface of the outside wall (Dim. B).
A minimum of 1 inch and a maximum of 48 inches
of building wall thickness is required for separated
combustion vent pipe.
Vent Connection Diameter
Vent terminals must be used. The optional vent kit
includes two terminals. Construct the vent system
as shown in the
drawings and
refer to the table
for the correct
vent connection
diameters.
Vent Length
Refer to table for
minimum and maximum
vent lengths. The
minimum vent length
is 5 feet and the maximum vent length is 50 feet. The
total equivalent vent length must include elbows. The
equivalent length of a 4inch elbow is 6feet and the
equivalent length of a 6inch elbow is 10feet.
Install Exhaust Pipe
Run an exhaust pipe from the unit’s combustion exhaust
through the exterior wall to the outdoors. The exhaust
pipe must terminate at least 12 inches from the outside
surface of the outside wall. Attach exhaust vent terminal
to the end of the exhaust pipe. Using field-supplied
mounting brackets, support the exhaust pipe as
needed.
Furnace Size
(MBH)
Exhaust
(inches)
Combustion
(inches)
75-175 4 4
200-400 6 6
Vent
Length
Minimum
(feet)
Maximum
(feet)
Horizontal 5 50
Install Exhaust Pipe
Slide the exhaust pipe through the CVA. Provide enough
exhaust piping to pass through the roof and provide the
minimum clearance of 12inches between the exhaust
pipe termination and the combustion air intake. With all
required clearances satisfied, attach the exhaust pipe to
the CVA.
Install Combustion Air Pipe
Attach a field-supplied combustion air pipe to the
concentric side of the CVA.
Be sure to provide enough combustion air piping
to pass through the roof and provide the minimum
clearance of 12 inches between the combustion
air intake and the exterior surface of the roof. This
clearance may need to be increased to allow for snow
accumulation.
Be sure to maintain the minimum clearance of
12inches between the exhaust pipe termination and the
combustion air intake.
Install CVA Assembly
Place the CVA assembly through the roof and verify
that all minimum clearance requirements as specified in
these instructions are met. Secure the CVA assembly to
the ceiling with corrosion-resistant sheet metal screws
through the mounting brackets.
Attach CVA Assembly to Unit
Attach the exhaust pipe to the unit’s combustion
exhaust. Using an additional combustion air pipe,
connect the unit’s combustion air supply intake to the
combustion air connection on the CVA.
Be sure to include the required tee’s with drip legs and
clean-outs.
Install Combustion Air Inlet Guard and
Exhaust Vent Terminal
Slide the combustion air terminal over the vent pipe and
fasten it to the combustion air pipe. Attach the exhaust
vent terminal to the discharge end of the exhaust piping.
Seal Opening
Seal the opening between the roofs and the air intake
pipe using an appropriate method.
A = 12 inch minimum
B = 24 inch minimum
C = 12 inch minimum
Exterior
Wall
EXHAUST
COMBUSTION AIR
Pitch vent pipe
downward
from furnace
¼ inch per foot Two (2) field-supplied
support brackets
Exhaust
Vent
Terminal
Combustion
Air Inlet
Terminal
C
B
A
®

Indirect Gas-Fired Heat Modules12
Install Combustion Air Pipe
Run a combustion air pipe from the unit’s combustion
air intake through the exterior wall to the outdoors. The
combustion air pipe must terminate at least 12inches
from the combustion vent pipe and 24inches from
the exterior surface of the outside wall. Attach the
combustion air inlet guard to the end of the combustion
air pipe. Using field-supplied mounting brackets,
support the combustion air pipe as needed.
Seal Wall Openings
Using an appropriate method, seal the wall openings
around the piping.
Installation of Two Pipe Venting –
Vertical
Refer to the diagram for venting vertical concentric
systems. The combustion air pipe must terminate at
least 12 inches above the roof. This clearance may
need to be increased to accommodate for snow
accumulation. The exhaust must terminate at least
12 inches above and 12 inches horizontally from the
combustion air inlet.
Vent Connection Diameter
Vent terminals must be
used. Construct the
vent system as shown
in the drawings and
refer to the table for the
correct vent connection diameters.
Furnace Size
(MBH)
Exhaust
(inches)
Combustion
(inches)
75-175 4 4
200-400 6 6
Vent Length
Refer to table for minimum and maximum vent lengths.
The minimum vent length is 10 feet and the maximum
vent length is 70 feet. The total equivalent vent length
must include elbows. The equivalent length of a 4 inch
elbow is 6feet and the
equivalent length of a
6inch elbow is 10feet.
Install Exhaust Pipe
Run an exhaust pipe from the unit’s combustion exhaust
through the roof to the outdoors. The exhaust pipe must
terminate at least 24 inches above the outside surface
of the roof. This clearance may need to be increased to
accommodate snow accumulation. Attach the exhaust
vent terminal to the end of the exhaust pipe.
Install Combustion Air Pipe
Run a combustion air pipe from the unit’s combustion
air intake through the roof to the outdoors. The
combustion air pipe must terminate at least 12 inches
horizontally and vertically from the combustion exhaust
pipe and at least 24 inches from the exterior surface of
the roof. These clearances may need to be increased
to accommodate for expected snow accumulation.
Attach the combustion air terminal to the end of the
combustion air pipe.
Seal Roof Penetration
Using an appropriate method, seal the roof openings
around the vent pipes.
Vent
Length
Minimum
(feet)
Maximum
(feet)
Vertical 10 70
A = 12 inch minimum, but should size
according to expected snow depth
B = 24 inch minimum
C = 12 inch minimum
D = 12 inch minimum
Tee with
drip leg and
clean-out cap
D
D
EXHAUST
Exhaust Vent
Terminal
COMBUSTION AIR
Combustion
Air Inlet
Terminal
Roof Line
B
A
C
®

Indirect Gas-Fired Heat Modules 13
Installation of Gas Piping
IMPORTANT
All gas piping must be installed in accordance
with the latest edition of the National Fuel Gas
Code ANSI/Z223.1 and any local codes that may
apply. In Canada, the equipment shall be installed
in accordance with the Installation Code for Gas
Burning Appliances and Equipment (CGA B149) and
Provincial Regulations for the class. Authorities having
jurisdiction should be consulted before installations
are made.
IMPORTANT
All piping should be clean and free of any foreign
material. Foreign material entering the gas train can
cause damage.
WARNING
All components of this or any other gas fired heating
unit must be leak-tested prior to placing the unit into
operation. A soap and water solution should be used
to perform this test. NEVER test for gas leaks with an
open flame.
IMPORTANT
Do NOT connect the unit to gas types other than
what is specified and do NOT connect the unit to
gas pressures that are outside of the pressure range
shown on the label.
WARNING
When leak testing pressures equal to or less than
14in. wg (3.5 kPa), first close the field-installed
shutoff valve to isolate the unit from the gas supply
line.
WARNING
When leak testing pressures above 14in. wg
(3.5kPa), close the field-installed shutoff valve,
disconnect the furnace and its gas train from the gas
supply line and plug the supply line before testing.
NOTE
When connecting the gas supply, the length of the
run must be considered in determining the pipe size
to avoid excessive pressure drop. Refer to a Gas
Engineer’s Handbook for gas pipe capacities.
NOTE
Each furnace has a single 3/4-inch connection.
Installation of Control Wiring
Disconnect power supply before making any wiring
connections to prevent electrical shock and equipment
damage.
All appliances must be wired strictly in accordance with
the wiring diagram furnished with the unit. Any wiring
different from the diagram could result in a hazard to
persons and property.
Any original factory wiring that requires replacement
must be replaced with wiring material having a
temperature rating of at least 105° C.
1. Installation of wiring must conform with local building
codes. In the absence of local building codes,
installation must conform to the National Electrical
Code and ANSI/NFPA 70 - Latest Edition. Unit must
be electrically grounded in conformance with this
code. In Canada, wiring must comply with CSA
C22.1, Canadian Electrical Code.
2. All furnaces are provided with a wiring diagram
located on the inside of the access panel or door to
the unit’s main control center. Refer to this diagram
for all wiring connections.
Installation of Discharge Air Sensor
Every furnace has a Discharge Air Sensor included.
It is typically attached to the terminal strip on the
furnace control center. If the ventilating unit has a
microprocessor controller, it will be connected to the
microprocessor controller. See the unit-specific wiring
diagram. Install sensor in the supply air duct, as far
downstream as possible for accurate temperature
measurement. Additional wire may be added to the
sensor as necessary.
®

Indirect Gas-Fired Heat Modules14
Connect the Supply Gas Line
A manual shut off valve (gas cock), a 1/8 inch plugged
test port and a drip leg must be installed between the
gas supply pipe and the start of the gas train. The valve
and test port must be accessible for the connection of a
test gauge. Supply gas connections must be made by a
qualified installer and are not furnished by manufacturer.
Determine the Gas Supply Requirements
The data label located on the face of the furnace lists
the requirements for the gas being supplied to the unit.
Ground
Joint
Union
8 in. Trap
Gas to
Controls
From Gas Supply
Bleeder Valve or
1/8 in Plugged Tap
Gas Cock
Typical Gas Supply Piping Connection
Type of
Gas Minimum
Gas
Supply
Pressure
Typical Furnace Data Label
each unit will be different
IMPORTANT
Before applying gas to the valves, test the gas
pressure to make sure it is less than 14 in. wg.
Pressures greater than 14 in. wg will damage the gas
valves.
Install Additional Regulator (if required)
If the gas supply pressure exceeds 14 in. wg, an
additional regulator must be installed to reduce the
pressure. The additional regulator is to be provided
and installed by others. The regulator must have a
listed leak limiting device or it must be vented to the
outdoors.
Test the System for Leaks
After installing the gas supply piping, perform a leak test
in accordance with the instructions in Installation of Gas
Piping in this manual. The leak test must be performed
before placing the unit in service.
Gas Pressure Test Ports
Burner manifolds and gas valves used in the furnaces
are supplied with test ports for temporary connection of
a pressure gauge or a magnehelic gauge.
Gas Supply In
Typical Split Burner Manifold
Test Ports
Typical Single Stage Gas Valve
Test Port
Test Port
ON / OFF
Gas Control Knob
®

Indirect Gas-Fired Heat Modules 15
Performance Data
Supply Air Temperature Rise
Model Input
(BTU/hr)
20°F 30°F 40°F 50°F 60°F 70°F 80°F 90°F 100°F
CFM
50 50,000 1852 1235 926 741 617 529 463 412 370
75 75,000 2778 1852 1389 1111 926 794 694 617 556
100 100,000 3704 2469 1852 1481 1235 1058 926 823 741
125 125,000 4630 3086 2315 1852 1543 1323 1157 1029 926
150 150,000 5556 3704 2778 2222 1852 1587 1389 1235 1111
175 175,000 6481 4321 3241 2593 2160 1852 1620 1440 1296
200 200,000 7407 4938 3704 2963 2469 2116 1852 1646 1481
225 225,000 8333 5556 4167 3333 2778 2381 2083 1852 1667
250 250,000 9259 6173 4630 3704 3086 2646 2315 2058 1852
275 275,000 10185 6790 5093 4074 3395 2910 2546 2263 2037
300 300,000 11111 7407 5556 4444 3704 3175 2778 2469 2222
325 325,000 12037 8025 6019 4815 4012 3439 3009 2675 2407
350 350,000 12963 8642 6481 5185 4321 3704 3241 2881 2593
400 400,000 14815 9877 7407 5926 4938 4233 3704 3292 2963
Sequence of Operation
Start-Up / Standby
Prior to start-up, verify that all field-installed sensors
have been installed. This includes a room temperature
sensor (optional) and a discharge air temperature sensor
(typical).
Heat Mode
When the unit or furnace controller calls for heat:
1. The ignition control will check that the pressure
switch for the combustion blower is open.
2. The combustion blower will energize and the
15second pre-purge begins.
3. The gas valve is energized and the igniter will spark
for up to 10 seconds. If a flame is not sensed during
the trial for ignition, two additional tries will be
attempted before going into lockout for one hour.
4. When a flame is sensed, sparking stops immediately.
The gas valve and combustion blower remain
energized.
5. Ignition
4:1 Electronic Modulation - The burner will light at
100% fire and remain there for up to 30 seconds.
The main burner gas valve will then modulate from
100% down to a minimum of 25%, as needed.
The combustion blower will change between high
and low speed to maintain acceptable combustion
airflow. If the high speed pressure switch does not
pull in when required, the furnace will lock out.
8:1 Stage Control - The furnace controller will ignite
the necessary manifolds at 100% for 30 seconds,
after which the unit or furnace controller will operate
the manifolds at high and low fire. Each time a
manifold is initialized, the manifold will ignite at
100%.
Single Stage Control - The burner will light at
100% and remain at high fire.
Two Stage Control - The burner will light at 100%
fire and remain there for 10 seconds. The unit or
furnace controller will operate the burners at either
high or low fire, depending on the demand for heat.
6. The ignition control constantly monitors the call for
heat, the pressure switch and the burner flame to
assure proper operation.
7. When the unit or furnace controls are satisfied,
the main gas valve is then de-energized and the
combustion blower shuts off following a 30 second
post-purge period.
Recovery from Lockout
If the furnace goes into lockout, the ignition control will
automatically reset after one hour if the thermostat is
still calling for heat. If needed, a manual reset can be
accomplished by either shutting off the power or turning
off the call for heat (turn off the thermostat) for a period
of five seconds.
®

Indirect Gas-Fired Heat Modules16
Gas Valves
Overview of typical Selectra Valve. Used in 2:1
Electronic Modulation
Low Fire
Adjusting Screw
Control Wire
Terminals
Vent
Overview of typical Single Stage Valve. Used in 4:1 and
2:1 Electronic Modulation and in Single Stage Furnaces
Gas Control Knob
(ON / OFF)
High Fire
Adjusting Screw
Overview of typical Two Stage Valve. Used in eight
stage and two stage furnaces.
Overview of typical Modulating Valve. Used in 4:1
Electronic Modulation
Low Fire and High Fire
adjustments are made
on printed circuit board
behind removable cover
Low Fire
Adjusting Screw
High Fire
Adjusting Screw
Terminal Block
Gas Control Knob
(ON / OFF)
Close-up of Terminal Block
High fire terminal is the bottom of
three terminals.
LO
C
HI
®

Indirect Gas-Fired Heat Modules 17
Furnaces with electronically modulated 4:1 turndown
use a combination valve for primary gas control. It
controls the high fire gas supply. In addition to the
combination valve, there is a modulating valve located
just after the combination valve. The modulating valve
is the device that modulates or changes the gas volume
that is being supplied to the furnace manifold. Both of
these valves require adjustment at the time of unit
start-up.
The modulating gas valve has a built-in digital controller
that will accept user settings for High Fire and Low Fire
and will provide minimal hysteresis throughout the entire
range of modulation. The modulating valve controls the
amount of combustion gas that goes to the burners,
while the combination valve acts as an on/off switching
device. During normal use, the amount of combustion
gas will vary constantly, depending on the settings put
in by the owner. This allows the modulating valve to
regulate the heat output from the furnace and maintain
a constant space temperature with minimal variation, or
hysteresis.
The modulating valve is controlled by a user interface
known as the FX controller. The FX controller sends an
analog signal to the modulating valve that causes the
valve to send more or less gas to the furnace.
The combination valve is normally closed. It requires
24VAC to hold it open.
With 4:1 Turndown Electronic
Modulation
Start-Up - Furnaces (all units)
After the gas piping has been installed and leak tested,
verify that all field-installed components such as an air
temperature sensor have been installed. Verify that ON/
OFF gas control knob on each stage-type gas valve is
turned to the “ON” position (see image).
Verify the unit turndown ratio as shown on page
2 of this manual. Consult the specific start-up
instructions as shown on the following pages to
accomplish the following steps:
Set Airflow
Airflow adjustment is done at the time of unit start-up.
Refer to the unit-specific Installation, Operating and
Maintenance manual (IOM) for instructions.
IMPORTANT
For the unit to function properly, ALL gas valves must
have their high fire and low fire settings adjusted for
field conditions.
IMPORTANT
Confirm the discharge air sensor is installed at least
three duct diameters downstream of the furnace.
IMPORTANT
Multi-furnace units may use a combination of the
available turndown options. Each furnace must be
set-up per the specific instructions for its control
type. For additional information, see Gas-Fired Burner
Turndown in this manual.
EXA Valve Single Stage
Valve
Single Section
Burner Manifold
Remote Temperature
Sensor
Ignition
Controller
FX Controller
®

Indirect Gas-Fired Heat Modules18
At start-up, remove the cover from the circuit board
housing by loosening the two Phillips head retaining
screws. Identify Button #1 and Button #2 and also
locate the LED indicator light.
Send the furnace to High Fire by following the
instructions below:
• Set the regulator screw on the combination valve
as high as it goes — all the way in.
• Set the High Fire set point on the modulating
valve to 3.5 in. wg for natural gas or 10.0in. wg
for LP gas.
• Set the Low Fire set point on the modulating gas
valve at 0.3 in. wg for natural gas or 1.0 in. wg for
LP gas.
The modulating valve has four electrical connections
on-board. Two are for the 24 VAC needed to power
the valve and two are for the input signal from the FX
controller. The location of the 24 VAC power source
varies, see the unit-specific wiring diagram. The input
signal that causes the modulating valve to change gas
volume is always provided by the FX controller and
varies from 2 - 10 VDC.
When a call for heat is provided to the FX controller,
the controller will first provide a 10 VDC signal to the
modulating valve so that it will always start in a high fire
condition. After ignition, the controller will change its
output signal, causing the volume of combustion gas to
be reduced to as little as 25% of full flow (4:1 turndown)
based on demand.
Adjust High Fire and Low Fire Settings
EXA Modulating Gas Valve
(with cover removed)
Terminals 3 & 4
(power)
Button #2
LED Light
Button #1
Terminals 1 & 2
(signal)
NOTE
Before setting the modulating valve, make certain the
combination valve is set to the maximum setting. Turn
the regulator screw all the way in.
Modulating Valve High Fire Setting
1. Connect a manometer to the test port on the burner
manifold.
2. Press and hold button #1 until the LED lights solid
red. Release the button. Observe the gas pressure
on the manometer.
3. Adjust the modulating
valve by pushing button
#1 to increase the
pressure or by pushing
button #2 to decrease
the pressure.
4. Save the High Fire setting by simultaneously
holding down buttons #1 and #2 until the LED
turns off. If the new setting is not saved within five
minutes, the modulating valve will default back to its
last saved setting.
Modulating Valve Low Fire Setting
1. With a manometer installed at the burner manifold
test port, press and hold down button #2 until the
LED blinks red. Release the button. Observe the gas
pressure on the manometer.
2. Adjust the Low Fire
setting by pushing
button #1 to increase
the pressure or by
pushing button #2 to
decrease the pressure.
3. Save the Low Fire setting by simultaneously
holding down buttons #1 and #2 until the LED
turns off. If the new setting is not saved within five
minutes, the Modulating Valve will default back to its
last saved setting.
Restore normal operation and shut off the furnace.
Reinstall the cover on the modulating valve, remove the
manometer and reinstall the plug in the manifold test
port.
NOTE
During the adjustment process, each push of either
button will increase or decrease the pressure in steps.
Holding down either button auto-steps and eliminates
the need to repeatedly push the button. Use this
feature to rapidly increase or decrease the gas flow.
High Fire Settings
Natural Gas 3.5 in. wg
LP Gas 10.0 in. wg
Low Fire Settings
Natural Gas 0.3 in. wg
LP Gas 1.0 in. wg
®

Indirect Gas-Fired Heat Modules 19
The modulating gas valve and the single stage valve are
both controlled by an A1092 Control System.
1. Connect a manometer to the test port on the burner
manifold.
2. Set the furnace to High Fire by turning the
temperature on the remote temperature selector dial
to maximum setting. This will cause both gas valves
to go into their high fire positions.
3. Set the high fire manifold gas pressure by turning
the adjusting screw on the single stage valve. The
correct pressure is 3.5 in. wg for
natural gas or 10.0 in. wg for LP
gas. Verify the unit is in high fire
by measuring VDC at modulating
valve. If greater than 15 VDC, then
the unit is in high fire.
4. Set the unit to low fire by
disconnecting one of the wires
connected to the top of the modulating valve.
5. Set the low fire on the modulating gas valve by
adjusting the needle valve on the side of the gas
valve. Low fire gas pressure should be 0.875 in. wg
for natural gas or 2.5 in. wg for LP gas.
6. Return the A1092 Controller to normal operation by
reconnecting the wire on the modulating valve and
turning down the temperature selector.
7. Shut down the furnace and then remove the
manometer from the manifold and reinstall the plug
in the test port.
8. Return the furnace to normal operation.
Furnaces with electronically modulated 2:1 turndown
use a single stage valve for primary gas control. It
controls the high fire gas supply.
In addition to the single stage gas valve, there is a
modulating gas valve located just after the combination
valve. Both of these valves require adjustment at the
time of unit start-up.
High Fire
Adjusting Screw
With 2:1 Turndown Electronic
Modulation
Typical Modulating
Gas Valve
Typical Single Stage
Gas Valve
Modulating
Valve
Single Stage
Valve
Single Section
Burner Manifold
Remote Temperature
Sensor
Remote
Temperature Dial Amplifier
MAXITROL
SELECTRA
MAXITROL
SELECTRA
A1092
50
70
80
90
60
MAXITROL
SELECTRA
Ignition
Controlle
r
®

Indirect Gas-Fired Heat Modules20
1. Connect a manometer to either test port on the
burner manifold.
2. Send the unit to high fire.
3. Check the gas pressure at the manifold test port. The
recommended pressure is 3.5 in. wg for natural gas
or 10.0 in. wg for LP gas.
4. Adjust the high fire screw on the valve
that is connected to the port being tested.
Counterclockwise rotation will decrease the gas
pressure and clockwise rotation will increase the
pressure.
5. Send the furnace to low fire by disconnecting and
isolating the wire from the high fire terminal on the
valve.
6. Check the gas pressure at the manifold test port.The
recommended low fire manifold pressure is 7/8in.
wg for natural gas or 2.5 in. wg for LP.
7. Adjust the low fire screw on the valve being tested.
Counterclockwise rotation will decrease the gas
pressure and clockwise rotation will increase the gas
pressure.
With 8 Stage Combustion
IMPORTANT
8 staged turndown furnaces use a split burner
manifold and two 2-stage gas valves per furnace.
The high fire and low fire manifold pressure must be
checked and properly set on each manifold.
Two Stage
Valve
Two Stage
Valve
Split Burner
Manifold
Remote Temperature
Sensor
FX Controller
Ignition
Controller
8. Turn off furnace. Reconnect the wire to the high fire
terminal. Remove manometer and reinstall plug into
manifold test port.
9. Connect manometer to the other manifold test port
and repeat the high fire / low fire set up sequence on
the other gas valve.
10.Turn off furnace. Reconnect the wire to the high fire
terminal. Remove manometer and reinstall plug into
manifold test port.
11.Return to the normal operation.
1. Connect a manometer to the test port on the burner
manifold.
2. Send the unit to high fire.
3. Check the gas pressure at the manifold test port. The
recommended pressure is 3.5 in. wg for natural gas
or 10 in. wg for LP gas.
4. Adjust the high fire screw on the valve.
Counterclockwise rotation will decrease the gas
pressure and clockwise rotation will increase the
pressure.
5. Turn off furnace. Remove manometer and reinstall
plug into manifold test port.
6. Return the unit to normal operation.
Single Section
Burner Manifold
Single Stage
Valve
Remote Temperature
Sensor
A350
JOHNSON
CONTROLS
A350
Controller
Ignition
Controller
With Single Stage
®