Grundig GT541023CW User manual

Dryer
User Manual
GT541023CW
GT5410231CW
2960313001/ EN/ / 18/07/2023 11:56

EN / 2
Table of Contents
1 Please read this guide before!..... 3
2 Safety Instructions........................ 4
2.1 Intended Use.................................. 4
2.2 Safety of Children, Vulnerable
Persons and Pets ..........................
4
2.3 Electrical Safety............................. 5
2.4 Transporting Safety....................... 5
2.5 Installation Safety.......................... 6
2.6 Usage Safety.................................. 8
2.7 Maintenance and Cleaning Safety 10
2.8 Lighting Safety............................... 10
3 Environmental instructions.......... 11
3.1 Compliance with the WEEE Regu-
lations and Waste Disposal ..........
11
3.2 Packaging Information.................. 11
3.3 Standard Conformity and Test In-
formation EU Declaration of Con-
formity............................................
11
4 Technical Specifications .............. 12
5 General Appearance..................... 13
5.1 Scope of Delivery........................... 13
6 First Operation .............................. 14
7 Installation ..................................... 14
7.1 Right Place for Installation ........... 14
7.2 Removing the Shipping Safety
Group..............................................
15
7.3 Water Connection.......................... 15
7.4 Adjusting the Legs......................... 16
7.5 Moving the Drying Machine .......... 16
7.6 Warnings Regarding the Noise..... 16
7.7 Replacing the Lighting Bulb .......... 16
7.8 Electrical Connection .................... 17
8 Preparation.................................... 18
8.1 Laundry Suitable for Drying in
Drying Machine..............................
18
8.2 Laundry Not Suitable for Drying in
Drying Machine..............................
18
8.3 Preparing the Laundry to Be Dried 18
8.4 What to Do for Energy Saving....... 18
8.5 Correct Load Capacity .................. 19
9 Running the Product .................... 20
9.1 Control Panel ................................. 20
9.2 Symbols ......................................... 20
9.3 Preparation of Drying Machine ..... 20
9.4 Program Selection and Consump-
tion Chart........................................
21
9.5 Auxiliary Functions ........................ 22
9.6 Warning Indicators......................... 23
9.7 Starting the Program ..................... 24
9.8 Child Lock....................................... 24
9.9 Changing the Program After It Is
Started ............................................
24
9.10 Cancelling the Program................. 25
9.11 End of Program.............................. 25
9.12 Odour Feature ................................ 25
10 Maintenance and Cleaning........... 25
10.1 Fiber Filters (internal and external
filters) / Cleaning of the Interior
Surface of the Loading Door .........
25
10.2 Cleaning the Sensor....................... 27
10.3 Emptying the Water Tank .............. 27
10.4 Cleaning the Condenser ................ 28
11 Troubleshooting ............................ 30
12 Product Information Voucher....... 33
13 GRUNDIG UK AND IRELAND
STANDARD MANUFACTURER
GUARANTEE TERMS AND CON-
DITIONS..........................................
34

EN / 3
1Please read this guide before!
Dear Customer,
Thank you for choosing Grundig product. We hope you get the best efficiency from this
product which has been manufactured with high quality and state of the art technology.
Please make sure you read and understand this guide and supplementary documentation
fully before using the product.
Observe all warnings and information herein. Therefore you can protect both yourself and
your product against potential damages.
Keep the user’s manual. Include this guide with the product if you hand it over to someone
else.
Symbols in the user manual and on your machine:
Danger that may result with death or injury.
Read the user’s manual.
Important information and useful hints about usage.
Flammable material, warning of fire hazard.
Warning against UV Radiation hazard.
The product's packaging is made of recyclable materials, in accordance with the National Environ-
ment Legislation.
Warning against hot surfaces.
Warning against electrical hazard.
NOTICE Danger that may cause material damage on the product or surrounding area.
This product has been manufactured at modern facilities respectful to the environment
without harming the nature.

EN / 4
2 Safety Instructions
• This section includes the in-
formation necessary to pre-
vent the risk of personal injury
or material damage. Our com-
pany shall not be held respons-
ible for damages that may oc-
cur if these instructions are not
observed.
• Always have the installation
and repair work carried out by
the manufacturer, an author-
ized service centre or a person
recommended by the importer
• Use original spare parts and
accessories only.
• Do not repair or replace any
component of the product un-
less it is clearly specified in the
user’s manual.
• Do not make technical modific-
ations on the product.
2.1 Intended Use
• Product is designed only for
household use. It is not inten-
ded for commercial use.
• The product is not designed
for outdoor use.
• Do not install or operate the
product in areas where freez-
ing is a possibility and/or
areas vulnerable to external ef-
fects. Water frozen in the
pump or the hoses may cause
damages.
• Product can only be used to
dry and ventilate laundry which
are washed with water and dry-
ing machine safe.
2.2 Safety of Children,
Vulnerable Persons
and Pets
• This product may be used by
children aged 8 years and
older and persons with under-
developed physical, sensory or
mental capabilities or lack of
experience and knowledge if
they have been given supervi-
sion or instruction concerning
safe use of the product and
the hazards involved. Children
should not tamper with the
device. Cleaning and mainten-
ance should not be carried out
by children unless they are su-
pervised.
• Children under 3 years of age
should be kept away from the
product unless they are con-
stantly supervised.
• Electrical products are danger-
ous for children and pets. Chil-
dren and pets should not play
with, climb on or get inside the
product.

EN / 5
• Keep the loading door of the
product closed even when not
operated.
• Cleaning and user mainten-
ance operations should not be
performed by children unless
supervised.
• Keep the packaging materials
away from children. There is
risk of injury and suffocation.
• Keep all additives used with
the product away from chil-
dren.
• Before disposing of the
product, cut the power cord
and destroy the loading door
for the safety of children.
2.3 Electrical Safety
• The product must not be
plugged in during installation,
maintenance, cleaning, repair
and transportation.
• If the power cable is damaged,
it must be replaced by a per-
son designated by the manu-
facturer, authorized service
centre or importer in order to
avoid potential hazards.
• Do not tuck the power cord un-
der the product or to the rear
of the product. Do not put
heavy items on the power
cord.
• Power cord should not be
kinked, pinched and should not
come in contact with any heat
source.
• Do not use an extension cord,
multi-plug or adaptor to oper-
ate the product.
• The product should not be
powered via an external switch
such as a timer or should not
be connected to a circuit that
is regularly opened and closed
with a tool.
• The plug should be easily ac-
cessible. If this is not possible,
a mechanism that complies
with the electrical legislation
and that disconnects all ter-
minals from the mains (fuse,
switch, main switch, etc.)
should be available on the
electrical installation.
• Do not touch the plug with wet
hands.
• When unplugging the appli-
ance, don’t hold the power
cord, but the plug.
2.4 Transporting Safety
• Unplug the product, empty the
water tank and if any, remove
the water drain connections
prior to transport.
• This product is heavy, do not
handle it by yourself.

EN / 6
• Take required precautions
against the risks of falling and
tipping of the product. Do not
crash or drop the product
when transporting.
• Do not use the extruding parts
of the product (such as the
loading door) to move the
product.
• Move the product in upright
position. If it cannot be moved
in upright position, transport
via tilting to the right side when
viewed from the front.
2.5 Installation Safety
• To make the product ready for
installation, ensure that the
electrical installation and wa-
ter drain are appropriate by
checking the information in the
user’s manual. If it is not suit-
able for installation, call a qual-
ified electrician and plumber to
make the necessary arrange-
ments. These operations shall
be undertaken by the cus-
tomer.
• This product is designed for
use at altitudes up to 2000
metres above sea level.
• Check for any damage on the
product before installing it. Do
not have the product installed
if it is damaged.
• Do not ever remove the ad-
justable legs.
• Place the product on a clean,
level and hard surface and bal-
ance with the help of the ad-
justable legs.
• The gap between the product
and the floor should not be re-
duced via materials such as
rugs, pieces of wood and
bands. The ventilation holes
under the base of the product
should not be clogged with a
rug.
• The product should be in-
stalled in such a way so as not
to clog the ventilation holes.
• Install the product in an envir-
onment free of dust with good
ventilation.
• Do not install the product in
close proximity to flammable
and explosive materials and do
not keep flammable and ex-
plosive materials near the
product when it is in operation.
• The product should not be in-
stalled behind a lockable door,
or a door with bolt where the
product loading door cannot
be completely opened, or a
hinged door where the product
hinge is faced against the
door’s hinges.

EN / 7
• Install the product in a place
where periodic maintenance
and cleaning can be done with
ease.
• Place the product with its back
surface facing the wall. (For
models with heating).
• While placing the product, en-
sure that the back wall does
not come in contact with any
extrusion (a water tap, elec-
trical outlet etc.).
• Place the product with at least
1 cm space between the
product and the furniture
edges.
• Follow the flue connection
rules specified in the manual.
(For models with flue).
• The discharged air should not
be directed to a flue which is
used to discharge the smoke
of devices that use gas or
other fuels. (For models with
flue).
• The ventilation hose should
not be connected to a heating
stove or a chimney flue. (For
models with flue).
• Plug the product to a grounded
outlet protected with an appro-
priate fuse in align with the
specified type and current
rates. Have an expert electri-
cian set grounding equipment.
Do not use the product without
a grounding conforming with
regional/national regulations.
• Plug the product in a grounded
socket that conforms with the
voltage, current and frequency
values specified in the type la-
bel.
• Do not plug the product to
loose, broken, dirty, greasy
sockets or sockets that have
come out of their seats or
sockets with a risk of water
contact.
• The new hose sets supplied
with the product should be
used. Do not re-use the old
hose sets. Do not make attach-
ments to the hoses.
• Place the power cord and
hoses in such a way so as not
to cause a risk of tripping over.
• Make sure that the hose does
not slip or fold if you directly
drain the water from the laun-
dry that is generated by the
condensation of the moisture.
Otherwise, water leaking prob-
lem may occur.
• Do not wash the dryer with
hose.
• To use the product on top of a
washing machine, a fixing
aperture should be used
between two products. Have
the fixing aperture installed by

EN / 8
the manufacturer, an author-
ized service centre or a person
specified by the importer.
• Do not use the product without
fixing it on floor-high ground,
such as on a table or cabinet
interior. When used without fix-
ation, it can move and fall over
time, damaging living things in
the environment or the objects
around it. The carrier floor
must be solid and stable.
• When the product is placed on
the washing machine, their
combined weight when full
could be around 180 kg. Place
the products on a sturdy floor
with an adequate load carrying
capacity.
• Washing machine cannot be
placed on top of the drying ma-
chine.
Suitable Instalment Table for Washing Machine and Drying Machine
Connection Kit Type Depth Size (DM: Drying Machine, WM: Washing Machine)
Plastic - 54/60 cm with/without arch 60cm DM --> WM≥50 cm / 54 cm DM --> WM≥45 cm
Plastic - 46 cm with/without arch 46 cm DM --> WM≥54 cm
With Shelves - 60 cm 60cm DM --> WM≥50cm
With Shelves - 54cm 54cm DM --> WM≥45cm
2.6 Usage Safety
• The maximum weight of dry
laundry prior to washing is spe-
cified in “Technical Specifica-
tions” section.
• Do not dry the unwashed items
in the drying machine.
• Do not machine dry clothes ex-
posed to substances like oil,
acetone, alcohol, petroleum,
kerosene, stain remover, tur-
pentine, massage oil, explos-
ives and combustibles,
beeswax and beeswax re-
mover, even if they have been
washed.
• If industrial chemicals are util-
ized for cleaning, the drying
machine should not be used.
• Softener or similar products
should be used as written in
the softener instruction.
• Rubber foam (latex foam),
shower bonnets, water resist-
ant textiles, rubber supported
materials, clothes with rubber
foam pads, and pillows should
not be dried in the drying ma-
chine.
• Yarn and fluffs dangling from
filled and damaged parts can
be dispersed in the machine
and damage your machine in

EN / 9
the drying process. Check the
seams of the laundry you are
going to dry.
• The items with hair spray, with
residue of hair product or sim-
ilar materials should not be
dried in the drying machine.
• Empty the pockets of the
clothes and remove all items
such as matches and lighters.
• Do not stop the drying ma-
chine before the completion of
the drying cycle if you won’t be
able to remove all the items
rapidly and to lay them down in
such a way that heat will be
dissipated.
• The last part of the drying ma-
chine cycle is conducted
without heating (cooling cycle)
in order to ensure that the
items are kept at a temperat-
ure that will not harm the
items.
• Laundry softeners or similar
products should be used in
align with the laundry softener
instructions.
• Do not use the drying machine
without the fiber filter.
• Do not allow fiber to accumu-
late around the drying ma-
chine.
• Do not operate the dryer with a
damaged fiber filter. Other-
wise, the machine may be
damaged by the collected fluff
and your machine's drying per-
formance may be adversely af-
fected.
• Clean the fiber filters after
each drying process.
• After washing the fiber filters,
dry them. Do not use filters
wet.
• To prevent back flow of gas to
the room from the devices that
consume other fuels, including
open fire, appropriate ventila-
tion should be provided (For
models with flue).
• Do not operate the product to-
gether with heaters such as
coal stove and gas heater and
a chimney. Airflow can cause
the flue to catch fire (For mod-
els with flue).
• Do not lean or sit on the load-
ing door when it is open, the
product may tip over.
• Do not get on the product.
• Do not place a source of flame
(burning candles, cigarettes,
etc.) on the product or in the vi-
cinity of it. Do not keep flam-
mable/explosive substances.
• Do not touch the drum as it re-
volves.
• During operation, the back wall
of the product becomes very
hot. Do not touch the back of
the product during drying or

EN / 10
immediately after the comple-
tion of drying (For models with
heating).
• Do not touch the inner surface
of the drum while adding or re-
moving clothes during a con-
tinuing programme. The drum
surface is hot.
• Do not press the buttons with
sharp objects such as forks,
knives, with your nails etc.
• Do not operate the faulty or
damaged product. Unplug the
product (or turn off the fuse to
which it is connected) and call
the manufacturer, an author-
ized service agent or a person
specified by the importer.
• Unplug the product when not
in use.
2.7 Maintenance and
Cleaning Safety
• Do not wash the product by
spraying or pouring water on it.
Do not use a pressure cleaner,
steam cleaner, hose or pres-
surised gun to clean the
product.
• Do not use sharp or abrasive
tools to clean the product.
• Do not use materials such as
household cleaning agents,
soaps, detergents, gas, gasol-
ine, thinner, alcohol, wax, etc.
to clean the product.
• The fiber filter should be fre-
quently cleaned. After each
drying cycle, clean the fiber fil-
ter and the inner surface of the
loading door.
• Clean the accumulated fiber
on the fins of the evaporator
behind the filter drawer with a
vacuum cleaner. You can clean
by hand, provided you wear
protective gloves. Do not try to
clean with bare hands. Evapor-
ator fins may damage your
hands (for products with heat
pump).
• Due to fire and explosion haz-
ard, do not use solutions,
cleaning materials, steel wool
or similar materials and tools
to clean sensors.
• Clean the flue (For models with
flue).
• Do not drink the condensed
water. Condensed water is not
potable water. This water can
harm human and animal health
if drunk.
2.8 Lighting Safety
• Contact an authorized service
when you need to replace the
LED/bulb used for lighting (for
products with lighting).

EN / 11
3 Environmental instructions
3.1 Compliance with the WEEE Regu-
lations and Waste Disposal
This product does not contain
the dangerous and prohibited
materials indicated in the "Reg-
ulation on The Control of
Waste Electrical and Electronic
Equipment” published by Min-
istry of Environment and Urbanisation of
the Republic of Turkey. Complies with
WEEE Regulation. This product was manu-
factured from recyclable and reusable high
quality parts and materials. Therefore, do
not dispose of this product with domestic
and other wastes at the end of its life cycle.
Take it to a collection point for recycling of
electrical and electronic equipment. You
can ask your local administration about
these collection points. Help protect the en-
vironment and natural resources by deliver-
ing the used products for recycling.
Also R290 is a flammable refriger-
ant. Therefore ensure that the sys-
tem and pipes are not damaged
during operation and transporta-
tion. Keep the product away from
possible heat sources, otherwise it
may catch fire if damaged. Do not
dispose of the product by throwing
it into fire.
3.2 Packaging Information
The product's packaging is made of recyc-
lable materials in accordance with the Na-
tional Legislation. Do not dispose of the
packaging waste with the household waste
or other wastes, deliver it to the packaging
collection areas specified by local authorit-
ies.
3.3 Standard Conformity and Test In-
formation EU Declaration of Con-
formity
The development, manufacturing
and sales phases of this product is
conducted in conformity with the
safety rules specified in all related
instructions of the European Union
The development, manufacturing
and sales phases of this product is
conducted in conformity with the
safety rules specified in all related
instructions of the Great Britian.

EN / 12
4 Technical Specifications
Height (adjustable) (cm) 84,6 * / 86,6 **
Width (cm) 59,8
Depth (cm) 60,7
Capacity (max.) (kg) 10 ***
Net weight (±10%) (kg) 44
Voltage
See the type label****Power
Main Model Code
* Min. height: Height with the adjustable legs closed.
** Max. height: Height with the adjustable legs opened at maximum height.
*** Weight of dry laundry before washing.
**** Type label is under the door on the drying machine.
In order to increase the drying machine’s quality, the technical specifications may be
changed without prior notice.
Figures in this manual are schematic and may not exactly match the product.
The values provided in the symbols on the drying machine or its accompanying documents
are values obtained in the laboratory environment in accordance with the respective stand-
ards. These values may differ depending on the use and ambient conditions of the drying
machine.

EN / 13
5 General Appearance
1
2
3
4
5
6
7
8
9
10
11
1 Upper table 2 Control Panel
3 Type label 4 Kickplate opening handle
5 Ventilation grills 6 Adjustable legs
7 For the models with tank located at
the bottom, the water tank is inside
the kickplate
8 Fiber filter
9 Loading door 10 Power cord
11 Water tank drawer (for models with
the tank on top)
5.1 Scope of Delivery
: User’s Manual
: Filter drawer sponge*
: Odour capsule group*
: Water discharge hose*
: Drying basket*
: Filter cloth*
: Water container*
: Brush*
*The optional accessory may not be avail-
able in the product.

EN / 14
6 First Operation
Remove the protective foil and adhesive ad-
vertising label if available in your product.
However, please do not remove the
labels (e.g. type label) that appear
after the lid is opened.
After the device is installed
• operate the machine for the first time ac-
cording to user’s manual.
7 Installation
Read the “Safety Instructions” first.
Before consulting the nearest Authorized
Service for installing the drying machine,
see the information in the user guide and
make sure the electric and water utilities
are as required. If it is not suitable for in-
stallation, call a qualified electrician and
plumber to make the necessary arrange-
ments.
It is customer's responsibility to prepare
the location the drying machine shall be
placed on and also have power and waste
water installation prepared.
Check for any damages on the dry-
ing machine before installing it. If
drying machine is damaged, do not
get it installed. Damaged products
cause a risk for your safety. Wait
for 12 hours before operating your
dryer after initial installation.
7.1 Right Place for Installation
NOTE: The product includes a cooling
agent and if the product is operated right
after it is transported, it may get damaged.
After each time the product is moved, it
shall be left to rest for 12 hours.
• Install the drying machine on a flat and
stable surface.
• Dryer machine is heavy. Do not move it
by yourself.
• Operate the drying machine in an environ-
ment free of dust with good ventilation.
• The gap between the drying machine and
the floor should not be reduced via ma-
terials such as rugs, pieces of wood and
bands.
• Do not block the ventilation grilles of the
drying machine.
• There shall not be doors that can be
locked, sliding doors or hinged doors
near the installation environment of the
drying machine that may block the load-
ing door to be opened.
• Once the drying machine is installed, the
connections must stay stable. While pla-
cing the drying machine, ensure that the
back wall does not come in contact with
any extrusion (a water tap, electrical out-
let etc.).
• Place the drying machine with at least 1
cm space between the product and the
furniture edges.
• Your drying machine is suitable to be op-
erated between +5 °C and +35 °C. If oper-
ated outside this temperature range, your
drying machine’s operation may be com-
promised and get damaged.
• The drying machine should be placed
with the back side facing a wall.
Do not place the drying machine on
its power cord.

EN / 15
Ignore this warning if the product
system does not contain R290*.
The dryer has R290 refrigerant gas.
R290 is an environmentally friendly
but flammable cooling gas. Make
sure the air intake of the dryer is
open and well ventilated. Keep pos-
sible flame sources away from the
dryer.
7.2 Removing the Shipping Safety
Group
Remove the shipping safety group prior to
first use of the product.
NOTE: Do not leave an accessory or any
parts of the shipping safety group inside
the drum.
7.3 Water Connection
Instead of periodically draining the water
accumulated in the water tank, you can dis-
charge it directly via the water discharge
hose supplied with the drying machine.
Connecting the water drainage hose
1. Manually pull the end of the hose behind
the dryer from where it is connected. Do
not use a tool to remove the hose.
2. Insert one end of the water discharge
hose supplied with the drying machine
to where you have removed the hose of
the drying machine.
3. Fix the other end of the water discharge
hose directly to waste water drainage or
a sink.

EN / 16
Fix the water discharge hose at a
maximum height of 80 cm.
Ensure that the water discharge
hose does not get kinked, collapsed
or pressed on between the dis-
charge and the drying machine.
Hose connection should be made
in such a way that it won’t come
out of its location. Leaked water
may cause damage.
Do not extend the water drainage
hose.
Check whether the water flows at
an adequate rate or not. The drain-
age line should not be closed or
clogged.
If an accessory package is provided
with your product, check the de-
tailed instructions.
7.4 Adjusting the Legs
Until the drying machine stands level and
sturdy, adjust the legs by turning them left
and right.
7.5 Moving the Drying Machine
• Drain the water in the drying machine
completely.
• If the product is connected via direct dis-
charge, remove the hose connections.
The drying machine is recommen-
ded to be moved in upright posi-
tion. If it cannot be moved in up-
right position, transport via tilting to
the right side when viewed from the
front. Wait for 12 hours prior to op-
erating the drying machine.
7.6 Warnings Regarding the Noise
While the product is being operated, it is
normal for a metallic noise to come from
the compressor from time to time.
The water that accumulates while the
product is being operated, is pumped to the
water tank via the pump. It is normal to
hear pumping sounds from the product dur-
ing this operation.
7.7 Replacing the Lighting Bulb
If your drying machine has drum lighting
lamp;
Consult the authorized service to replace
the bulb/LED used in lighting your drying
machine. The bulb in this product is not
suitable for home lighting. The intended
use of this lamp is to ensure safely loading
the laundry to the drying machine. The

EN / 17
lamps used in this appliance should be res-
istant to inappropriate physical conditions
such as temperatures over 50 °C.
7.8 Electrical Connection
Make sure that you have an earthed power
outlet socket rated at 13 amps (minimum).
Attention!
When installed, the socket must be reach-
able after installation, or a separate switch
(which can disconnect the two poles) must
be used in the installation. Check for suit-
ability.
For a permanent connection, a master
switch with at least 3mm contact clearance
and minimum 13 A rating must be used.
Electrical requirements
Before you insert the plug into the wall
socket make sure that the voltage and the
frequency shown in the rating label corres-
ponds to your electricity supply.
We recommend that this appliance be con-
nected to the mains supply via a suitable
switched and fused socket in a readily ac-
cessible position.
Should the mains lead of the appliance be-
come damaged or need replacing at any
time, it must be replaced by a special pur-
pose made mains lead which can only be
obtained from an Authorised Service Agent
This appliance must be earthed If
the fitted moulded plug is not suit-
able for your socket, then the plug
should be cut off and an appropri-
ate plug fitted.
The moulded plug on this appliance
incorporates a 13A fuse. Should the
fuse need to be replaced an ASTA
approved BS1362 fuse of the same
rating must be used. Do not forget
to refit the fuse cover. In the event
of losing the fuse cover, the plug
must not be used until a replace-
ment fuse cover has been fitted.
Colour of the replacement fuse
cover must be the same colour as
that visible on the pin face of the
plug. Fuse covers are available
from any good electrical store.
In order to avoid hazards, damaged
supply cord should be replaced by
the manufacturer, its service agent
or similarly qualified people.
Do not operate without the top
cover fitted. Risk of injury.
Fitting a different plug
As the colours of the wires in the mains
lead of this appliance may not correspond
with the coloured markings identifying the
terminals on your plug, proceed as follows:
1. Connect the green - yellow or green
(earth) wire to the terminal in the plug
marked ‘E’ or with the symbol or col-
oured green and yellow or green.
2. Connect the blue (neutral) wire to the
terminal in the plug marked ‘N’ or col-
oured black.
3. Connect the brown (live) wire to the ter-
minal in the plug marked ‘L’ or coloured
red.
With the alternative plugs a 13 A fuse must
be fitted either in the plug or adaptor or in
the main fuse box. If in doubt contact a
qualified electrician.

EN / 18
Washer/dryer combination
Do not stack washing machine on top of
the tumble dryer. This would damage both
appliances and guarantees would become
void. It is also unsafe to stack an appliance
on top of another without using a suitable
and approved stacking kit obtained from
specialist retailers.
8 Preparation
Read the “Safety Instructions” first!
8.1 Laundry Suitable for Drying in
Drying Machine
Laundry that are not drying machine safe
may damage the appliance and the laundry
during drying. Follow the instructions on
the labels of the laundry to be dried. Only
dry the laundry with the “drying machine
safe” labels by choosing the suitable pro-
grams.
8.2 Laundry Not Suitable for Drying in
Drying Machine
• Undergarments with metal supports
should not be dried in drying machine. If
these metal supports get loose and
ripped from the garment, they may dam-
age the machine.
• Delicate embroidery textiles, woollen and
silk garments, garments manufactured
from delicate and valuable textiles, non
breathing garments and tulle curtains
should not be dried in drying machine.
• Pay attention to the drying symbols on
the label on the laundry. Dry laundry with
the label or symbol that says it is suitable
for drying in the dryer.
8.3 Preparing the Laundry to Be Dried
Items such as coins, metal parts, needles,
nails, screws, stones etc. may damage the
drum group of the product or may cause
functional operation issues. Therefore
check all laundry that will be loaded to the
product.
• Dry the laundry with metal accessories
such as zippers by turning them inside
out.
• Close the zippers, hooks and clasps, but-
ton up the covers’ buttons, tie textile
belts and apron belts.
8.4 What to Do for Energy Saving
Use the highest possible spinning cycle as
you wash the laundry. Therefore you can re-
duce the drying period and reduce energy
consumption. Sort the laundry based on
their types and thickness. Dry same types
of laundry together. For instance thin kit-
chen towels and table cloths dry faster than
thick bathroom towels.
• Follow the recommendations in the
user’s manual for program selection.
• During drying do not open the loading
door unless necessary. If you are re-
quired to open the loading door, do not
keep it open for too long.
• Do not add wet laundry as the drying ma-
chine operates.
• Clean the Fiber Filter before and after
each drying session.
• For models with condensation, be sure to
clean the condenser regularly at least
once a month or after 30 drying sessions.

EN / 19
• Make sure the filters are clean. Refer to
maintenance and cleaning section for de-
tails.
• For models with flue, follow the flue con-
nection rules specified in the guides and
clean the flue.
• During drying session, properly ventilate
the environment where the drying ma-
chine is located.
• In models with heat pump, check the con-
denser at least every six months and
clean it if it is dirty.
• If you are using environment friendly fil-
ter, you are not required to clean the filter
after every cycle. When the environment
friendly icon is lit on the screen, change
the filter cloth.
8.5 Correct Load Capacity
If the laundry in the product exceed max-
imum loading capacity, it may not operate
as intended and may cause material dam-
age or product damage. For each program,
follow the maximum loading capacity. Be-
low you can see the laundry and their ap-
proximate weight.
Duvet Cover Set: 1000-1500 g
Flat Sheet: 350-500 g
Table Cover: 250-700 g
Towel: 350-700 g
Dress: 350-500 g
Denim Trousers: 500-700 g
T-shirt: 125-200 g
Blouse: 150-250 g
Shirt: 200-300 g

EN / 20
9 Running the Product
9.1 Control Panel
1 2345678
1 On/Off/Programme selection button. 2 Dryness level selection button.
3 Drum light and wrinkle prevention se-
lection button.
4 Audible warning and child lock selec-
tion button.
5 Low temperature selection button. 6 Time program selection button.
7 End time selection button. 8 Start / Standby selection button.
9.2 Symbols
9.3 Preparation of Drying Machine
• Plug the drying machine.
• Open the loading door.
• Place the laundry in the drying machine
without jamming them.
• Push and close the loading door.