GSD WXT26M2601B User manual

Hui Zhou Gaoshengda Technology Co., LTD WXT26M2601B
PAGE 1 OF 2 Version 1.0
WIFI+BT Module
IEEE 802.11 a/b/g/n/ac/ax 2T/2R
Model Number: WXT26M2601B
Product Descrition
The WXT26M2601B is a complete dual-band(2.4GHz and 5GHz)WIFI 2×2 MIMO module. This module provides a
high level of integration with a dual-stream IEEE 802.11ax MAC/ base band /radio and Bluetooth 5.2.The WLAN
operation supports 20MHz,40MHz and 80MHz channels for data rates up to 1201Mbps. It fully complies with IEEE
802.11 a/b/g/n/ac/ax feature rich wireless connectivity at high standards,delivers reliable,cost-effective,
throughput from an extended distance.
Product Features
Product Specification
Model WIF+BT Module
Product Name WXT26M2601B
Standard 802.11 a /b/g/n/ac/ax
Interface USB
Data Transfer Rate 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120 and maximum of 1201Mbps
Modulation Method GFSK,π/4-DQPSK,8DPSK(bluetooth)
DQPSK,DBPSK,CCK(802.11b)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11g)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11a)
QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac)
QPSK,BPSK,16QAM,64QAM,256QAM,1024QAM with OFDM (802.11ax)
Frequency Band BLUETOOTH
2402~2480 MHz
WIFI
2.4G: 2412~2462 MHz
5G: 5150~5250MHz,5725~5850MHz
Operation Mode Infrastructure
Security WEP, TKIP, AES, WPA, WPA2
Operating Voltage 3.3V±10%
Current Consumption ＜1000mA
Antenna Type PIFA
Operating
Temperature
0 ~ 70°C ambient temperature
Storage Temperature -40 ~ 80°C ambient temperature
Humidity 5 to 95 % maximum (non-condensing)
◆Complies with IEEE 802.11b/g/n/ax for 2.4GHz and IEEE 802.11a/n/ac/ax 5GHz Wireless LAN.
◆Bluetooth v5.2
◆Two transmit and Two receive path(2T2R)
◆Works with all existing network nfrastructure.
◆Capable of up to 128-Bit WEP Encryption.
◆Freedom to roam while staying connected.
◆UP to 1201 Mbps High-Speed Transfer Rate in 802.11ax mode of operation.
◆Operating Systems：Linux,Win7, Win8, Win10,XP
◆Low power consumption.
Easy to install and configure.◆
◆Hi
g
h s
p
eed USB 2.0 interface

Hui Zhou Gaoshengda Technology Co., LTD WXT26M2601B
PAGE 2 OF 2 Version 1.0
NOTICE:
◆please keep this product and accessories attached to the places which children can't touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight, otherwise it may cause
deformation or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM
Manual v01
2.2 List of applicable FCC rules
FCC Part 15 Subpart C 15.247 & 15.209&407
2.3 Specific operational use conditions
The module is a WIFI+BT Module
IEEE 802.11 a/b/g/n 2T/2R
Operation Frequency: 2402-2480MHz/2412-2462/5150~5250MHz,5725~5850MHz
The module can be used for mobile or portable applications with a maximum (2.4G WIFI:2.0dBi,5G WIFI:3.0
dBi,BT:2.0dBi)antenna. The host
manufacturer installing this module into their product must ensure that the final composit product
complies with the FCC requirements by a technical assessment or evaluation to the FCC rules,
including the transmitter operaition. The host manufacturer has to be aware not to provide information
to the end user regarding how to install or remove this RF module in the user's manual of the end
product which integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.
2.4 Limited module procedures
Not applicable. The module is a Single module and complies with the requirement of FCC Part 15.212.
2.5 Trace antenna designs
Not applicable. The module has its own antenna, and doesn’t need a host’s printed board microstrip
trace antenna etc.
2.6 RF exposure considerations
The module must be installed in the host equipment such that at least 20cm is maintained between the
antenna and users’ body; and if RF exposure statement or module layout is changed, then the host
product manufacturer required to take responsibility of the module through a change in FCC ID or new
application. The FCC ID of the module cannot be used on the final product. In these circumstances,
the host manufacturer will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
2.7 Antennas
Antenna Specification are as follows:
Type: PCB Antenna
Gain: 2.4G WIFI:2.0dBi
5G WIFI:3.0dBi
BT:2.0dBi
This device is intended only for host manufacturers under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna;
The module shall be only used with the internal antenna(s) that has been originally tested and certified
with this module. The antenna must be either permanently attached or employa ‘unique’ antenna
coupler.
As long as the conditions above are met, further transmitter test will not be required. However, the
host manufacturer is still responsible for testing their end-product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC peripheral
requirements, etc.).
2.8 Label and compliance information
Host product manufacturers need to provide a physical or e-label stating “Contains FCC ID: 2AC23-WX726
” with their finished product.
2.9 Information on test modes and additional testing requirements

Hui Zhou Gaoshengda Technology Co., LTD WXT26M2601B
PAGE 3 OF 2 Version 1.0
Host manufacturer must perfom test of radiated & conducted emission and spurious emission, etc
according to the actual test modes for a stand-alone modular transmitter in a host, as well as for
multiple simultaneously transmitting modules or other transmitters in a host product.
Only when all the test results of test modes comply with FCC requirements, then the end product can
be sold legally.
2.10 Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.247 & 15.209 and that
the host product manufacturer is responsible for compliance to any other FCC rules that apply to the
host not covered by the modular transmitter grant of certification. If the grantee markets their product
as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then
the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
Federal Communication Commission Statement (FCC, U.S.)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTES
Co-location warning:
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
OEM integration instructions:
This device is intended only for OEM integrators under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna. The
module shall be only used with the external antenna(s) that has been originally tested
and certified with this module.
As long as the conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization for this
module in combination with the host equipment is no longer considered valid and the
FCC ID of the module cannot be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the
transmitter) and obtaining a separate FCC authorization.

Hui Zhou Gaoshengda Technology Co., LTD WXT26M2601B
PAGE 4 OF 2 Version 1.0
End product labeling:
The final end product must be labeled in a visible area with the following: “Contains
Transmitter Module FCC ID: 2AC23-WXT26
Information that must be placed in the end user manual:
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user's manual of the end product which
integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.