PicoBrew PicoFerm User manual

picoferm
instruction
manual
Fermentation is one of the most important steps to your
brew. PicoFerm takes the guesswork out and ensures
you’ve fermented your brew accurately.
unboxing registering connecting using
picoferm factory reset
You can navigate through chapters by
clicking on the tabs here.

unboxing registering connecting using
picoferm factory reset
23
picoferm instruction manual
• PicoFerm
• PicoFerm Fermentation Seal (GRAY)
• 2 AA batteries
• QuickStart Guide
what's
in the
box

45picoferm instruction manual
connecting
and
registering
picoferm
1. Insert two, AA batteries (included) into PicoFerm, then
press the ON/STATUS button. All the indicator lights
should illuminate and stay on.
2. Using a Wi-Fi connected smart phone or similar device,
browse to picobrew.com/setup/picoferm and follow the
on-screen instructions.
• Wi-Fi Connection
• Access to an internet browser
• Pico C and Pico C Brew Keg (or a Cornelius ball lock
keg with the PicoFerm Ball Lock adapter)
what you will need:
Note: You can choose to power your PicoFerm with a Mi-
cro-USB cable connected to a wall plug. We do not recommend
connecting PicoFerm to a computer to power it.
unboxing registering connecting using
picoferm factory reset

67picoferm instruction manual
connecting
picoferm to
your keg
To get the most out of your PicoFerm, ensure that it is
connected securely and correctly. Follow steps 1A-4A
below if you are using a Pico C Keg, or steps 1B-3B if you
are using a ball-lock keg.
unboxing registering connecting using
picoferm factory reset

89picoferm instruction manual
Pico C Keg.
We recommend that you sanitize your
PicoFerm Fermentation Seal before you
connect it to your brew keg. We recommend
Star San for this purpose. Only sanitize the
bottom of the Fermentation Seal so that no
liquid backs up into your PicoFerm.
Let the Fermentation Seal air dry before
attaching it to your keg.
₁aConnect the GRAY PicoFerm Fermentation
Seal that was included with your PicoFerm
to the Pico C brew keg. Be sure that the
Fermentation Seal is pressed all the way
against the keg.
2a
unboxing registering connecting using
picoferm factory reset

10 11picoferm instruction manual
Activate your PicoFerm by pressing the ON/
STATUS button.
Attach the PicoFerm to the Fermentation Seal.
Note: only use the GRAY PicoFerm
Fermentation Seal while fermenting beer
with PicoFerm. Do not use when brewing
Kombucha. Also, always depressurize
the keg before removing or replacing
PicoFerm.
₃a龎a
unboxing registering connecting using
picoferm factory reset

12 13picoferm instruction manual
Ball Lock Keg.
Connect the Ball Lock Keg adapter to the
PicoFerm as shown.
Note: Be sure to use the red Fast
Fermentation Adapter when fermenting with
your ball lock keg.
₁bInsert the barbed fitting on the Ball Lock
into the Keg Adapter.
2b
unboxing registering connecting using
picoferm factory reset

14 15picoferm instruction manual
Connect the Gray Ball Lock Connector on
the PicoFerm to the post on the Brew Keg
marked “IN”.
₃b
unboxing registering connecting using
picoferm factory reset

16 17picoferm instruction manual
using
picoferm
Press the ON/STATUS button to activate indicator lights
and check fermentation status.
Note: if you see a flashing red light, this means that there is
an error with your fermentation. Log in to your BrewHouse
to see error details.
Indicator Light What It Means
Flashing green light Beer is done fermenting
Flashing yellow light Fermentation in progress
Yellow and green lights PicoFerm is updating
Flashing green and red lights PicoFerm is not associated with an
account
Red, yellow and green lights
flash in sequence
PicoFerm is communicating with pico-
brew.com
Green, yellow, red all on Access Point Mode
Yellow and red blinking Error during fermentation
unboxing registering connecting using
picoferm factory reset

18 19picoferm instruction manual
viewing brew data with brewhouse
After your PicoFerm is attached and activated, click on
BrewHouse at picobrew.com to enable PicoFerm to monitor
your brew session.
Find the beer that you are ready to ferment in your list of
brews, and click the ‘FERMENT’ button.
Next, select ‘Temp Detection’ and then select your PicoFerm
from the dropdown list that appears. Your PicoFerm is now
associated with this brew session.
You can view fermentation data for your beer at any time by
clicking the ‘FERMENT’ button for the associated brew.
You can also change the ‘Yeast Pitched’ date at any time if the
entered date is incorrect. This will adjust the fermentation
countdown in BrewHouse accordingly.
viewing brew data with brewpulse
Coming Soon!
unboxing registering connecting using
picoferm factory reset