GSD W2TM2510 User manual

Hui Zhou Gaoshengda Technology Co., LTD W2TM2510
PAGE 1 OF 3 Version 1.0
WIFI Module
IEEE 802.11 b/g/n 2T/2R
Model Number: W2TM2510
Product Descrition
The W2TM2510 is a 2.4GHz 2×2 MIMO WIFI module. This module provides a high level of integration with a dual-stream IEEE
802.11n MAC/ base band /radio.The WLAN operation supports 20MHz,40MHz channels for data rates up to 300Mbps. It fully
complies with IEEE 802.11 b/g/n feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput
from an extended distance.
Product Features
Product Specification
Model WIFI Module
Product Name W2TM2510
Standard 802.11 b/g/n
Interface USB
Data Transfer Rate 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90 and maximum of 300Mbps
Modulation Method DQPSK,DBPSK,CCK(802.11b)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11g)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n-HT20)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n-HT40)
Frequency Band 2400~2483.5 MHz
Frequency Range: 2412~2462 MHz
Antenna Type: PIFA Antenna
Antenna Gain: Chain 0 2dBi
Chain 1 2dBi
Operation Mode Infrastructure
Security WEP, TKIP, AES, WPA, WPA2
Operating Voltage 3.3V±10%
Current Consumption ＜1000mA
Antenna Type PIFA
Operating Temperature 0 ~ 60°C ambient temperature
Storage Temperature -40 ~ 80°C ambient temperature
Humidity 5 to 95 % maximum (non-condensing)
◆Complies with IEEE 802.11b/g/n for 2.4GHz Wireless LAN.
◆Two transmit and Two receive path(2T2R)
◆Works with all existing network nfrastructure.
◆Capable of up to 128-Bit WEP Encryption.
◆Freedom to roam while staying connected.
◆UP to 300 Mbps High-Speed Transfer Rate in 802.11n mode of operation.
◆Operating Systems：Linux,Win7, Win8, Win10,XP
◆Low power consumption.
Easy to install and configure.◆High speed USB 2.0 interface◆ROHS com
p
liant◆
FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247

Hui Zhou Gaoshengda Technology Co., LTD W2TM2510
PAGE 2 OF 3 Version 1.0
NOTICE:
◆please keep this product and accessories attached to the places which children can't touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight, otherwise it may cause deformation
◆or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
We will retain control over the final installation of the modular such that compliance of the end product is assured. In such cases, an operating condition
on the limit modular approval for the module must be only approved for use when installed in devices produced by a specific manufacturer. If any
hardware modify or RF control software modify will be made by host manufacturer,C2PC or new certificate should be apply to get approval,if those
change and modification made by host manufacturer not expressly approved by the party responsible for compliance ,then it is illegal.
The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between
the radiator and user body.
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter
Module FCC ID:2AC23-W2T Or Contains FCC ID:2AC23-W2T”
When the module is installed inside another device, the user manual of the host must contain below warning
statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with
the product.
Any company of the host device which install this modular with limit modular approval should perform the test of radiated & conducted emission and
spurious emission,etc. according to FCC part 15C : 15.247 and 15.209 & 15.207 ,15B Class B requirement, Only if the test result comply with FCC part
15C : 15.247 and 15.209 & 15.207 ,15B Class B requirement，then the host can be sold legally.

Hui Zhou Gaoshengda Technology Co., LTD W2TM2510
PAGE 3 OF 3 Version 1.0
CE Statement
Herby, Hui Zhou Gaoshengda Technology Co., LTD declares that this WIFI Module，W2TM2510 is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.
In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.
Use the WIFI Module in the environment with the temperature between 0℃and 60℃
Operation Frequency: 2412MHz~2472MHz
Max Output Power: 0.0453W
Manufacturer：Hui Zhou Gaoshengda Technology Co., LTD
Address：NO.75 Zhongkai Development Area, Huizhou, Guangdong, China
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
Canada Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. Le
fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable de l'appareil.
IC Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device.
This modular complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user
body. Cette modulaire doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et le corps de l'utilisateur.
If the IC number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a
label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 12290A-W2T”
When the module is installed inside another device, the user manual of this device must contain below warning statements;
1. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device
2. Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. Le
fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable de l'appareil.
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.

Hui Zhou Gaoshengda Technology Co., LTD W2TM2510
PAGE 4 OF 3 Version 1.0
Declaration of Conformity
I hereby declare that the product
Product:
Product Name: WIFI Module
Model: W2TM2510
Brand Name: GSD
Hardware Version: V1.0
Software Version: V0.13
satisfies all the technical regulations applicable to the product within the scope of Council
Directives 2014/35/EU, 2014/30/EU and 2014/53/EU:
EN 60950-1: 2006+A11: 2009+A1: 2010+A12: 2011+A2: 2013
EN62311:2008
Draft ETSI EN 301 489-17 V3.2.0 (2017-03)
Draft ETSI EN 301 489-1 V2.2.1 (2019-03)
Final draft ETSI EN 300 328 V2.2.1 (2019-04)
(Title(s) of regulations, standards, etc.)
All essential radio test suites have been carried out.
NOTIFIED BODY: LGAI Technological Center S.A./Applus(Nr. 0370), has conducted the conformity assessment
according to module B of Directive 2014/53 / EU (RED)
−Address:
Ronda de la Font del Carme, s/n
08193 Bellaterra – Barcelona
(Spain)
Identification Number: 0370
MANUFACTURER or AUTHORISED REPRESENTATIVE:
−Address:
Hui Zhou Gaoshengda Technology Co., LTD
NO.75 Zhongkai Development Area, Huizhou, Guangdong, China
This declaration is issued under the sole responsibility of the manufacturer and, if applicable, his authorised representative.
Signature:
Jul.15, 2019
Name Hui Guan
Position N/A
Company Name Hui Zhou Gaoshengda Technology Co., LTD
Address NO.75 Zhongkai Development Area, Huizhou, Guangdong, China
Tel / Fax [phone]
E-Mail [email protected]