GSD GSDs-1FP Technical manual

“Wireless Network
System”
GSD Wi-Enterprise/Wi-Plus System is the
next generation in access control solutions.
It provides a Wireless Network throughout
the premises, giving the convenience and
security of a fully networked system for a
fraction of the cost.
For more information on the Wireless Network System visit our website
www.globalsecurity.ie
No.1 Turnpike Business Park,
Ballymount,
Dublin 22, Ireland.
Telephone: [phone]
Fax: [phone].
2
Contents
4
Installation Diagrams
8
5
Features
Finger Print Switch
Other products from GSD
Wiring Diagrams
3
Best Practices
10
Administration Notes
6
Operation Instructions
Finger Placement
Operation Instruction:
Place Finger on Senor Window

11
12
13
14
15
16
21
22
23
24
25
26
31
32
33
34
35
41
42
43
44
45
46
User Administrator
User
Location User Name Finger Reference
Administration Notes
User
Location User Name Finger Reference
51
52
53
54
55
56
61
62
63
64
65
66
Administration Notes
Note: Users are enrolled to the User Locations defined in the table above only.

“Wireless Network
System”
GSD Wi-Enterprise/Wi-Plus System is the
next generation in access control solutions.
It provides a Wireless Network throughout
the premises, giving the convenience and
security of a fully networked system for a
fraction of the cost.
For more information on the Wireless Network System visit our website
www.globalsecurity.ie
No.1 Turnpike Business Park,
Ballymount,
Dublin 22, Ireland.
Telephone: [phone]
Fax: [phone].
2
Contents
4
Installation Diagrams
8
5
Features
Finger Print Switch
Other products from GSD
Wiring Diagrams
3
Best Practices
10
Administration Notes
6
Operation Instructions
Finger Placement
Installation & User Manual V2.01

2
Power Supply 12V DC
Current consumption 70mA
Current consumption with load (max) 100mA
Relay Contact Rating 5 Amps /240V ac
Operating Temperature - 20 C to +60 C
Moisture Resistance IP 65
Dimensions - Surface Mount W. 87mm D. 35mm H. 160mm
Number of Users 35
Technical Specs
Features
Features
Controls 1 Door
35 Users
Door Monitoring via Door Contact
Tamper Resistant
Easy Programming
Programmable Settings:
- Programming Code
- Relay Active Time
- Silent or Audible Operation
- Keypad Backlight
- Scan Mode
- Inputs/Outputs Options
Indoor/Outdoor Use - IP 65
Robust Polycarbonate Housing
Mounts onto Standard Electrical Patress Box
Note: Engineering mode status Led indicators.
Amber Led flashing indicates that the unit is in Engineering mode.
Red Led flashing indicates user needs to enter data or present finger.
Present a finger at any stage to exit engineering mode. Otherwise it will
time out automatically.
User
Location User Name Finger Reference
51
52
53
54
55
56
61
62
63
64
65
66
Administration Notes
Note: Users are enrolled to the User Locations defined in the table above only.

11
12
13
14
15
16
21
22
23
24
25
26
31
32
33
34
35
41
42
43
44
45
46
3
Quick Reference
Restoring Factory Settings
Example: To Restore Factory Default Settings
Code Description
55 Restoring Factory Default Settings
Enter
Engineer
Code + + Present Finger
to Confirm
Note: If programming code is lost, Remove the Security Caps (see page 4) and
hold down the 5 key during power-up and enter the default Engineer code
‘6666’ immediately. This will restore the factory settings.
Best Installation Practice
1 Always Default the Door Control to Factory Settings before
commencing programming.
2 It is important to ensure that the varistor supplied with the Door
Control is fitted across the lock terminals on all installations.
Factory Default PIN codes
The following PIN codes are the Factory Default Settings:
- The Default Engineer code is ‘6666’
- User PIN ‘1111’
Note: The User PIN ’1111’ is deactivated when the first User is added to the
keypad.
Code = 55
10
User Administrator
User
Location User Name Finger Reference
Administration Notes

12V
Example: To Change the Engineer Code to 1234
Changing Engineer Code
Code Description
4 Changing the Engineer Code
Enter
Engineer
Code + + 1234
New Eng Code
Changing Settings
Code Description
6 Changing Backlight, Silent or Scan Mode
Example: To Toggle the Backlight to ‘Always On’ or ‘Only On after a Key
Press’
Example: To Toggle the Silent Operation On/Off
Example: To Toggle the Sensor Scanning Mode to Always On/Off
Note: If Sensor Scanning Mode is set to Off, the Red Sensor light will
be off in normal standby conditions and placing a finger on the sensor
window will not operate the Door Control.
To re-activate the Scan Sensor - press any key before placing the finger
on the Sensor window.
Enter
Engineer
Code + + 1
Enter
Engineer
Code + + 2
Enter
Engineer
Code + + 3
9
Operation Instructions
Code = 4
Amber LED flashes Red LED flashes Amber LED flashes
Code = 6
Code = 6
Code = 6
Amber LED flashes Red LED flashes Amber LED flashes
Amber LED flashes Red LED flashes Amber LED flashes
Amber LED flashes Red LED flashes Amber LED flashes
4
12V Linear
Power supply
Door
Contact
0V
Door
Exit Button
0V
Interlock OP to
Interlock IP on
2nd Door
Interlock IP from
Interlock OP on
2nd Door
12V Sounder
Important:
Always fit the varistor supplied
with the unit between the
lock terminals as shown
NC
COM
NO
0V
12V
Door MagLock
Always connect a
varistor between a
solid ground OV and
the NC for a maglock.
Varistor
0V
Varistor
12 - 24 VAC
12 - 24 VAC
Wiring for StikeLock only using 12 - 24VAC supply
12V Linear
Power supply
Door
Contact
0V
Door
Exit Button
0V
Interlock OP to
Interlock IP on
2nd Door
Interlock IP from
Interlock OP on
2nd Door
12V Sounder
Important:
Always fit the varistor supplied
with the unit between the
lock terminals as shown
NC
COM
NO
0V
12V
OP2
OP1
IP1
IP2
IP3
Wiring Diagrams
Default Door Exit
Button Door
Contact Interlock
I/P
Table 1
Page 5
Input 1 Input 2 Input 3 Output 2
Output 1 Wiring
Diagrams
Alarm/
Buzzer
Interlock
O/P
Note: All OV shown in the diagram are connected
to OV at the back of the keypad terminal block.
0V
NC
COM
NO
0V
12V

Operation Instructions
Example: To Change the Relay Time to 15 seconds
Changing Relay Time
Code Description
3 Changing the Relay Time
Enter
Engineer
Code + + + Present Finger
to Confirm
8
Example: To Enrol a Users Fingerprint in User Location 22
To enrol a users fingerprint , the users finger must be presented ‘twice’ to the
scansensor window. The scan sensor must get 2 good quality readings to have a
successful enrolment.
As per the steps above present the finger to the sensor window until confirmation
beep is heard and Red Led turns off momentarily. Remove and re-present the
finger for the second time to complete the enrolment. A successful enrolment will
be followed by an Access Granted Tone.
Example: To Remove Users Fingerprint from User Location 34
Enrolling and Removing Users
Code Description
1 Enrol a User Fingerprint
2 Remove a User Fingerprint
Enter
Engineer
Code + +
Code = 1
Note: Refer to pages 6 & 7 for correct/incorrect finger placement.
Enter
Engineer
Code + +
User Loc. = 22
+
Present Finger
to Enroll
+
Present Finger
to Enroll
Code = 2 User Loc. = 34
Code = 3 Seconds = 15
Amber LED flashes Red LED flashes Red LED flashes
Amber LED flashes Red LED flashes Amber LED flashes
Amber LED flashes Red LED flashes Red LED flashes
To re-attach Security Caps simply align
tabs into holes as shown above and
ease the Caps back into place using
a flat bladed screwdriver.
Finger Print Switch is mounted to pattress box using security
screws provided. Both Security Caps are
then clipped onto Finger Print
Switch.
Flush Mounting
To release Security Caps push a
flat bladed screwdriver into slots
on the side and pull forward gently.
5
Wiring Diagrams

Correct Finger Placement Incorrect Finger Placement
7
Finger Placement
6 Finger Placement