Pilz PSSu H FS SN SD User manual

PSSu H FS SN SD (M12) (-T)(-R)
Operating Manual-1001451-EN-13
}Decentralised system PSSuniversal I/O

Preface
This document is the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for the user's internal purposes. Suggestions and comments for improving this documenta-
tion will be gratefully received.
Source code from third-party manufacturers or open source software has been used for
some components. The relevant licence information is available on the Internet on the Pilz
homepage.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital

Contents
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 3
1 Introduction ............................................................................................................................5
1.1 Validity of documentation.......................................................................................................... 5
1.1.1 Retaining the documentation .................................................................................................... 5
1.2 Definition of symbols................................................................................................................. 5
2 Overview .................................................................................................................................7
2.1 Module features ........................................................................................................................ 7
2.2 Front view ................................................................................................................................. 8
3 Safety ...................................................................................................................................... 11
3.1 Intended use ............................................................................................................................. 11
3.2 Safety regulations ..................................................................................................................... 11
3.2.1 Use of qualified personnel ........................................................................................................ 11
3.2.2 Warranty and liability ................................................................................................................ 12
3.2.3 Disposal .................................................................................................................................... 12
4 Function description ............................................................................................................. 13
4.1 Block diagram ........................................................................................................................... 13
4.2 Supply voltage .......................................................................................................................... 13
4.2.1 Function description.................................................................................................................. 13
4.2.2 Current load capacity................................................................................................................ 13
4.3 Integrated protection mechanisms............................................................................................ 15
4.4 SafetyNET p ............................................................................................................................. 15
4.4.1 Connection to SafetyNET p ...................................................................................................... 15
4.5 Decentralised inputs and outputs ............................................................................................. 16
4.6 SD card..................................................................................................................................... 16
4.7 Reset button ............................................................................................................................. 17
5 Installation ..............................................................................................................................18
5.1 General installation guidelines.................................................................................................. 18
5.2 Dimensions ............................................................................................................................... 18
5.3 Installing the head module........................................................................................................ 18
6 Interface assignment ............................................................................................................. 20
7 Wiring ......................................................................................................................................21
7.1 General wiring guidelines ......................................................................................................... 21
7.2 Terminal configuration .............................................................................................................. 21
7.3 Connecting the module............................................................................................................. 22
8 Operation ................................................................................................................................23
8.1 Messages ................................................................................................................................. 23
8.2 Display elements ...................................................................................................................... 23
8.2.1 MBUS ....................................................................................................................................... 24
8.2.2 SD CARD.................................................................................................................................. 25
8.2.3 DIAG ......................................................................................................................................... 26
8.2.4 ST SNp ..................................................................................................................................... 27
8.2.5 FS SNp ..................................................................................................................................... 28

Contents
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 4
8.2.6 5V, 24V ..................................................................................................................................... 29
8.2.7 X3: LNK, X3: TRF, X4: LNK, X4: TRF ...................................................................................... 30
9 Technical details ....................................................................................................................31
9.1 Safety characteristic data ......................................................................................................... 38
10 Order reference ......................................................................................................................39
10.1 Product ..................................................................................................................................... 39
10.2 Accessories .............................................................................................................................. 39

Introduction
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 5
1 Introduction
1.1 Validity of documentation
The documentation is valid for the product types:
}PSSu H FS SN SD
}PSSu H FS SN SD–T
}PSSu H FS SN SD M12-T
}PSSu H FS SN SD–R
}PSSu H FS SN SD M12-R
}It is valid until new documentation is published.
Please also refer to the following documents:
}System Description PSS 4000
}PSSuniversal Installation Manual
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
1.1.1 Retaining the documentation
This documentation is intended for instruction and should be retained for future reference.
1.2 Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.

Introduction
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 6
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.
INFORMATION
This gives advice on applications and provides information on special fea-
tures.

Overview
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 7
2 Overview
2.1 Module features
The head module belongs to the performance class "Decentralised system PSSuI/O". It
can be used to connect a PSSu system to SafetyNETp. The head module has the follow-
ing features:
}2 free switch ports for connection to SafetyNETp
}Standard module bus for standard I/O modules
}Safety module bus for safety I/O modules
}SD card used to store the device project and the naming data
}Reset pushbutton
– For warm reset
– To transfer the naming data and/or device project from the SD card to the device
memory
}Supply voltage
– Integrated supply voltage for periphery supply and module supply
– Module supply is buffered for 20ms if the supply voltage is interrupted
– Plug-in connection terminals (either spring-loaded terminal or screw terminal)
}Status LEDs
}T-type:
PSSu H FS SN SD (M12)-T: For increased environmental requirements
}R-type:
PSSu H FS SN SD (M12)-R: For railway applications

Overview
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 8
2.2 Front view
Front view of head modules with an RJ45 female connector
7
Reset

Overview
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 9
Front view of head modules with an M12 female connector
1
2
3
44
6
57
Legend
1 SafetyNETp interface
2 SafetyNETp interface
3 Labelling strip (see below for details)
4 Status LEDs
5 SD card
6 Reset pushbutton
7 Supply voltage connection (module and periphery supply)

Overview
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 10
The labelling strip contains the following information:
Order number
Serial number
Hardware version
2D code:
Product
information
MAC address
2D code:
MAC address
MAC
ADD
0002
4840
3152
312085
100017
HW 001

Safety
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 11
3 Safety
3.1 Intended use
The module is suitable for use in safety and non-safety-related applications with
SafetyNETp.
The modules PSSu H FS SN SD and PSSu H FS SN SD-T may be used as a safety com-
ponents in accordance with the Lifts Directive 95/16/EC in accordance with the require-
ments of EN81-1/2:1998+A3:2009, EN81-20:2015, EN81-50:2015, EN81-22:2014 and
EN115-1:2008+A1:2010.
The programmable safety system should be installed in a protected environment that meets
at least the requirements of pollution degree 2. Example: Protected inside space or control
cabinet with protection class IP54 and corresponding air conditioning.
The module PSSu H FS SN SD (M12)-T is suitable for use where there are increased en-
vironmental requirements (see Technical Details).
The module PSSu H FS SN SD (M12)-R is suitable for use where there are increased en-
vironmental requirements demanded by railway applications (see Technical details).
Intended use includes making the electrical installation EMC-compliant. Please refer to the
guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use
in an industrial environment. It is not suitable for use in a domestic environment, as this can
lead to interference.
The following is deemed improper use in particular:
}Any component, technical or electrical modification to the module
}Use of the module outside the areas described in this manual
}Any use of the module that is not in accordance with the technical details.
3.2 Safety regulations
3.2.1 Use of qualified personnel
The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by competent persons.
A competent person is a qualified and knowledgeable person who, because of their train-
ing, experience and current professional activity, has the specialist knowledge required. To
be able to inspect, assess and operate devices, systems and machines, the person has to
be informed of the state of the art and the applicable national, European and international
laws, directives and standards.
It is the company’s responsibility only to employ personnel who
}Are familiar with the basic regulations concerning health and safety / accident prevention,
}Have read and understood the information provided in the section entitled Safety
}Have a good knowledge of the generic and specialist standards applicable to the specific
application.

Safety
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 12
3.2.2 Warranty and liability
All claims to warranty and liability will be rendered invalid if
}The product was used contrary to the purpose for which it is intended,
}Damage can be attributed to not having followed the guidelines in the manual,
}Operating personnel are not suitably qualified,
}Any type of modification has been made (e.g. exchanging components on the PCB
boards, soldering work etc.).
3.2.3 Disposal
}In safety-related applications, please comply with the mission time TM in the safety-related
characteristic data.
}When decommissioning, please comply with local regulations regarding the disposal of
electronic devices (e.g. Electrical and Electronic Equipment Act).

Function description
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 13
4 Function description
4.1 Block diagram
4.2 Supply voltage
4.2.1 Function description
The product provides the module supply and periphery supply for the modules on the mod-
ule bus:
}Module supply
Supply voltage for subsequent module (right-hand side)
}Periphery supply
Supply voltage for sensors, actuators and test pulses
When the supply voltage is fed in separately, the module supply and periphery supply are
galvanically isolated. If galvanic isolation is not required, a common power supply may be
used for the periphery supply and module supply.
4.2.2 Current load capacity
Ensure you comply with the current load capacity of the module and periphery supply (see
"Technical Details"). If the current load is higher, an additional supply voltage module is re-
quired to refresh the module supply and periphery supply.
}Module supply
The current load is the total current consumption of all the electronic and compact mod-
ules.
The module supply does not automatically switch off if values exceed or drop below their
limits. However, the "5 V" LED will light and a message will be entered in the diagnostic
list.
}Periphery supply

Function description
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 14
The current load is the total current consumption of the sensors, actuators and test
pulses supplied via the input/output modules.
The periphery supply does not automatically switch off if values exceed or drop below
their limits. However, the "24V" LED will light and a message will be entered in the dia-
gnostic list.
Please refer to the derating diagrams.
PSSu H FS SN SD: Derating diagram for periphery supply: Temperature T dependent on
load current I
T (°C)
20
40
60
80
100
0
1 2 3 4 5 6 7 8 9 10 I (A)
PSSu H FS SN SD(-T)(-R): Derating diagram for periphery supply: Permitted ambient tem-
perature T dependent on load current I
20
40
60
80
100
0
5 10
T [°C]
I [A]
76 8 921 3 4

Function description
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 15
PSSu H FS SN SD(-T)(-R): Derating diagram for infeed for module supply: Permitted ambi-
ent temperature T dependent on load current I
20
40
60
80
100
0
1 2
T [°C]
I [A]
1,41,2 1,6 1,80,40,2 0,6 0,8
4.3 Integrated protection mechanisms
The module has the following protection mechanisms:
}Multi-channel diverse processor section
}Cyclical self tests
}Potentially isolated SafetyNETp interface
}Infeed for module supply
– Polarity protection
– Voltage monitoring
– Transient voltage limitation
– 20 ms voltage buffer if the supply voltage is interrupted
}Module supply
– Short circuit-proof
}Periphery supply
– Voltage monitoring (exceeding upper/lower limit)
4.4 SafetyNET p
4.4.1 Connection to SafetyNET p
Functions
}The SafetyNETp interface enables I/Os to be controlled by means of a higher level con-
trol system (e.g. PSSu PLC).
}The head module receives signals from a higher level control system and forwards them
to the connected input/output modules.

Function description
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 16
}The head module receives signals from the connected input/output modules and forwards
them to a higher level control system.
}If a fault occurs, the module switches the connected failsafe outputs to a safe condition.
MAC address
}The MAC address is a factory-set default. It can found on the labelling strip on the front of
the module.
INFORMATION
Further information on SafetyNETp can be found in the "PSS4000 System
Description".
4.5 Decentralised inputs and outputs
The head module belongs to the performance class "Decentralised system PSSuI/O". It
enables the PSSuniversal to be used as a modular, decentralised input/output module:
}PSSu system without control functionality
}Electronic modules and/or compact modules must be added to the head module
}I/Os are controlled via SafetyNETp by means of a control system (e.g. PSSu PLC)
4.6 SD card
The SD card has the following functions:
}The SD card is used to store the naming data and the device project; see PSS4000 Sys-
tem Description.
}The SD card is part of the safety concept on PSS4000. If the SD card is missing or has
been swapped, the next time the PSSu system is booted it will be unable to achieve the
operating status "PSSu System in RUN condition without error". The SD card has a lock-
ing mechanism, which protects it from being removed from the card holder unintention-
ally. The SD card can also be sealed to protect it from manipulation, whether accidental
or intentional.
Sealing the SD card for additional protection:

Function description
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 17
4.7 Reset button
The "Reset" pushbutton on the head module has various functions:
}Perform a warm reset for the PSSu system.
The reset pushbutton can be used to perform a warm reset for the PSSu system.
}Transfer the naming data and/or device project from the SD card (deliberate operator ac-
tion to transfer the naming data and/or device project from the SD card to the device
memory).
INFORMATION
The warm reset and the transfer of the naming data and/or device project
are described in the "PSS4000 System Description". This is also where the
general effects on the PSSu system are described in detail.

Installation
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 18
5 Installation
5.1 General installation guidelines
Please also refer to the PSSuniversal Installation Manual.
The description below assumes that the mounting rail is already installed.
NOTICE
Damage due to electrostatic discharge!
Electrostatic discharge can damage components. Ensure against discharge
before touching the product, e.g. by touching an earthed, conductive sur-
face or by wearing an earthed armband.
5.2 Dimensions
5.3 Installing the head module
Prerequisite:
}The mounting rail must be installed.
Please note:
}All contacts should be protected from contamination.
Procedure:
}Install an end bracket to the left of the head module or leave enough space for one.
}Slot the groove on the head module on to the mounting rail from below [1].
}Push the head module back as far as it will go [2].
}Make sure that the locking mechanisms [3] are pushed downwards, connecting the mod-
ule firmly to the mounting rail.

Installation
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 19
Schematic representation:

Interface assignment
Operating Manual PSSu H FS SN SD (M12) (-T)(-R)
1001451-EN-13 | 20
6 Interface assignment
Further information on the Ethernet interface can be found in the system description
PSS4000.
Assignment of the interfaces on head modules with an RJ45 female connector
SafetyNET p Assignment
RJ45 female connector 1: TD+
2: TD-
3: RD+
4: n.c.
5: n.c.
6: RD-
7: n.c.
8: n.c.
8 1
Shield
}n.c. = not connected
Assignment of the interfaces on head modules with an M12 female connector
SafetyNET p Assignment
4-pin M12 female connector
D-coded
1: TD+
2: RD+
3: TD-
4 RD-
5: Connection to functional
earth on the connector hous-
ing
5