WAGO 750-402 User manual

Pos:2/Dokumentationallgemein/Einband/EinbandHandbuch- D ec kbl att ohne Varia nt enfel d ( Sta n dar d) @ 9\mod_1285229289866_0.docx@ 64941@ @ 1
Manual
WAGO-I/O-SYSTEM 750
4DI 24V DC 3.0ms
750-402(/xxx-xxx)
4-Channel Digital Input Module 24 V DC, 2- to 3-
conductor connection; high-side switching
Version 1.1.0
Pos: 3/ All e S eri en (Al lg em eine M od ul e)/Hi nw eise zur D oku men tat ion/I m pres sum für St and ard han dbüc h er - all g. Ang aben, A nschri ften, Tel efonn ummer n und E-Mail -Adr essen @ 3\mod_1219151118203_21.docx@ 21060@ @ 1

2 WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
© 2013 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]om
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]om
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende d er Liste f ür T e xtmar ke Ei nb and _v orne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 5/ Do ku ment ati on all ge mein /V erzei ch niss e/I nhal tsv erz eich nis - Ü ber schrif t oG und Verz eich nis @ 3\mod_1219151230875_21.docx@ 21063@ @ 1
Table of Contents
Table of Contents................................................................................................... 3
1Notes about this Documentation................................................................. 5
1.1 Validity of this Documentation................................................................. 5
1.2 Copyright................................................................................................... 5
1.3 Symbols..................................................................................................... 6
1.4 Number Notation....................................................................................... 8
1.5 Font Conventions ...................................................................................... 8
2Important Notes........................................................................................... 9
2.1 Legal Bases ............................................................................................... 9
2.1.1 Subject to Changes............................................................................... 9
2.1.2 Personnel Qualifications....................................................................... 9
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions...... 9
2.1.4 Technical Condition of Specified Devices......................................... 10
2.2 Safety Advice (Precautions).................................................................... 11
3Device Description ..................................................................................... 13
3.1 View........................................................................................................ 15
3.2 Connectors............................................................................................... 16
3.2.1 Data Contacts/Internal Bus................................................................. 16
3.2.2 Power Jumper Contacts/Field Supply ................................................ 17
3.2.3 CAGE CLAMP®Connectors............................................................. 18
3.3 Display Elements .................................................................................... 19
3.4 Schematic Diagram................................................................................. 20
3.5 Technical Data ........................................................................................ 21
3.5.1 Device data......................................................................................... 21
3.5.2 Supply................................................................................................. 21
3.5.3 Communication .................................................................................. 21
3.5.4 Inputs.................................................................................................. 21
3.5.5 Connection Type ................................................................................ 22
3.5.6 Climatic Environmental Conditions................................................... 22
3.6 Approvals................................................................................................ 23
3.7 Standards and Guidelines........................................................................ 25
4Process Image............................................................................................. 26
5Mounting..................................................................................................... 27
5.1 Mounting Sequence................................................................................. 27
5.2 Inserting and Removing Devices ............................................................ 28
5.2.1 Inserting I/O Module.......................................................................... 28
5.2.2 Removing the I/O Module.................................................................. 29
6Connect Devices ......................................................................................... 30
6.1 Connecting a Conductor to the CAGE CLAMP®................................... 30
6.2 Connection Examples.............................................................................. 31
6.2.1 2-Conductor Connection .................................................................... 31
6.2.2 3-Conductor Connection .................................................................... 31
7Use in Hazardous Environments.............................................................. 32

4 Table of Contents WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
7.1 Marking Configuration Examples........................................................... 33
7.1.1 Marking for Europe according to ATEX and IEC-Ex........................ 33
7.1.2 Marking for America according to NEC 500..................................... 38
7.2 Installation Regulations........................................................................... 39
7.2.1 Special conditions for safe use (ATEX Certificate TÜV 07 ATEX
554086 X)........................................................................................... 40
7.2.2 Special conditions for safe use (ATEX Certificate TÜV 12 ATEX
106032 X)........................................................................................... 41
7.2.3 Special conditions for safe use (IEC-Ex Certificate TUN 09.0001 X)42
7.2.4 Special conditions for safe use (IEC-Ex Certificate IECEx TUN
12.0039 X).......................................................................................... 43
7.2.5 ANSI/ISA 12.12.01 ............................................................................ 44
List of Figures...................................................................................................... 45
List of Tables........................................................................................................ 46
=== En de der Lis te für T extmar ke Verz eich nis_vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 7/ All e S eri en (Al lg em eine M od ul e)/Üb ers chr ift en für all e S erie n/Hi n weis z ur D ok umen ta tion/ Hin weis e z ur D o kume ntati on - Ü b ersc hri ft 1 @ 4\mod_1237987661750_21.docx@ 29029 @ 1@ 1
1 Notes about this Documentation
Pos: 8/ All e S eri en (Al lg em eine M od ul e)/Hi nw eise zur D oku men tat ion/H i nweis e/H in weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx@ 29026 @ @1
Keep this documentation!
The operating instructions are part of the product and shall be kept for the entire
lifetime of the device. They shall be transferred to each subsequent owner or user
of the device. Care must also be taken to ensure that any supplement to these
instructions are included, if applicable.
Pos: 9/ All e S eri en (Al lg em eine M od ul e)/Üb ers chr ift en für all e S erie n/Hi n weis z ur D ok umen ta tion/ Gül tig kei tsber ei ch - Ü bersc hrift 2 @ 12\mod_1338912448776_21.docx@ 96469@2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S erie 7 50 (WA GO-I/O-SYS TEM )/H in weis e z ur D ok ument ati on/ Gül tigk eits ber eic h D okum ent atio n B us klem me 7 50-xxx x, Stan dard versio n und aufg elist ete Var iante n @ 14\mod_1358944038682_21.docx@ 109354@ @ 1
This documentation is only applicable to the I/O module 750-402 (4DI 24V DC
3.0ms) of the WAGO-I/O-SYSTEM 750 series and the variants listed in the table
below.
Pos: 11 /S erie 7 50 (WA GO-I/ O-SYST EM) /Hi n weis e zur Do kume ntati on/ Var ia ntenl ist en/V ari ant enl iste - 750-xxx- St andar dversi on und V aria nte /025-00 0 ( erw eit ert er T em per atur ber eic h) @9\mod_1281521920414_21.docx@ 63093@ @ 1
Table 1: Variants
Item Number/Variant
Designation
750-402
4DI 24V DC 3.0ms
750-402/025-000
4DI 24V DC 3.0ms/T
Pos: 12 /S erie 7 50 (WA GO-I/O-SYS TEM) /Hi nweis ez ur Do kume ntati on/Hi nweis e/Ac htung : Hinw eis zur D oku ment ation B uskl emme n 750-xxxx @ 4\mod_1237986979656_21.docx@ 29023@ @ 1
The I/O module 750-402 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 13 .1 /All e Seri en( Allg emeine M odul e)/Hi nweis e zur Do kument ation /Urh ebersc hutz au sführ lich @ 4\mod_1235565145234_21.docx@ 27691@ 2@ 1
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos:13.2/Dokumentationallgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 13 .3 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erie n/Hin weis zur D oku mentati on/S ymbol e- Ü b erschr if t 2 @ 13\mod_1351068042408_21.docx@ 105270@ 2 @ 1
1.3 Symbols
Pos: 13.4 .1 /Alle Ser ien ( Allge meine Mo dule) /Wic htige Er läut erung en/Si cherh eits- undsonstigeHinweise/Gefahr/Gefahr: _Warnung vorPersonenschädenallgemein_- Er l äuter ung @ 13 \mod_1343309450020_21.docx@ 101029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 13 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nstig eH inwei se/G efahr /Gefa hr: _War nung vor Per son enschä den durc h elek trisc hen Str om_ - Erläuterung@ 13\mod_1343309694914_21.docx@ 101030@ @1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 13 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und s ons tig e Hin wei se/ War nung /W arn ung: _War nu ng vor Per so nensc h äde n allg em ein_ - Erläuterung @ 13\mod_1343309877041_21.docx@ 101035@ @1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 13 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und s ons tig e Hin wei se/ Vors ic ht/V ors ich t: _ War nung vor P ers one nsc häde n al lg em ein_ - Er lä uterung@ 13\mod_1343310028762_21.docx@ 101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 13 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweise/Achtung/Achtung:_Warnung vorSachschäden allgemein_- Erläuterung@ 13\mod_1343310134623_21.docx@ 101041@ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 13 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweise/Achtung/Achtung:_Warnung vorSachschäden durchelektrostatische Aufladung_- Erläuterung @13\mod_1343310227702_21.docx@ 101044@ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 13 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstige Hinweise/Hinweis/Hinweis:_Wichtiger Hinweis allgemein_- Eräuterung @ 13\mod_1343310326906_21.docx@ 101047@ @1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 13 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und s ons ti ge H in weis e/I nf or mati on/I nf or mati on: _Wei ter e I nfor ma tio n al lg emei n_ -Er l äut er ung @ 13\mod_1343310439814_21.docx@ 101051@ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos:13.5/Dokumentationallgemein/Gliederungselemente/---Seite nwec hsel--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 13 .6 /All e Seri en( Allg emeine M odul e)/Hi nweis e zur Do kument ation /Zahl ensy steme @ 3\mod_1221059454015_21.docx@ 21711@ 2 @ 1
1.4 Number Notation
Table 2: Number notation
Number code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 13 .7 /All e Seri en( Allg emeine M odul e)/Hi nweis e zur Do kument ation /Schr iftko nventi one n @ 3\mod_1221059521437_21.docx@21714 @ 2 @ 1
1.5 Font Conventions
Table 3: Font conventions
Font type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Programme\WAGO-I/O-CHECK
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 14 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 15 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erien/Wichtige Erläuterungen/WichtigeErläuterungen- Üb ersc hrift 1 @ 4\mod_1241428899156_21.docx@ 32170 @ 1 @ 1
2 Important Notes
Pos: 16 .1 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/Ei nleit ung Wic htige E rläut erung en @ 3\mod_1221059818031_21.docx@21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 16 .2 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erie n/Wich tige Er läuter ung enRec htlic he Grun dlag en -Ü bersc hrift 2 @ 3\mod_1221060626343_21.docx@ 21726@ 2 @ 1
2.1 Legal Bases
Pos:16.3/Alle Serien( AllgemeineDokumente)( AllgemeineModule)/Wichtige Erläuterungen/Änderungsvorbehalt- Über schri ft 3 und In halt @ 3\mod_1221060036484_21.docx@ 21720@ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos:16.4/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Per sonal qual ifika tion 75 0-xxxx@ 3 \mod_1224061208046_21.docx@ 24063@ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on Series 750 devices may only be carried out by
electrical specialists with sufficient knowledge in automation. The specialists
must be familiar with the current norms and guidelines for the devices and
automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos:16.5/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Bes timm ungsg emäß e Verwe ndung 7 50-xxxx @ 3\mod_1224064151234_21.docx@24070 @ 3 @ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Couplers, controllers and I/O modules found in the modular WAGO-I/O-
SYSTEM 750 receive digital and analog signals from sensors and transmit them
to the actuators or higher-level control systems. Using programmable controllers,
the signals can also be (pre-) processed.
The components have been developed for use in an environment that meets the
IP20 protection class criteria. Protection against finger injury and solid impurities
up to 12.5 mm diameter is assured; protection against water damage is not
ensured. Unless otherwise specified, operation of the components in wet and
dusty environments is prohibited.
Operating 750 Series components in home applications without further measures
is only permitted if they meet the emission limits (emissions of interference)
according to EN 61000-6-3. You will find the relevant information in the section
on "WAGO-I/O-SYSTEM 750" "System Description" "Technical Data" in
the manual for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 16 .6 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/T echnis cher Z ustan d der Ger äte - Übers chri ft 3 und Inh alt @ 3\mod_1221060446109_21.docx@ 21723@ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The components to be supplied Ex Works, are equipped with hardware and
software configurations, which meet the individual application requirements.
WAGO Kontakttechnik GmbH & Co. KG will be exempted from any liability in
case of changes in hardware or software as well as to non-compliant usage of
components.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos:16.7/Dokumentationallgemein/Gliederungselemente/---Seite nwec hsel--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 16 .8 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erie n/Wich tige Er läuter ung enSic herhei tshi nweis e- Üb ersc hrift 2 @ 6 \mod_1260180299987_21.docx@46724 @ 2@ 1
2.2 Safety Advice (Precautions)
Pos: 16 .9 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/Si cherh eits hinwei se/Ei nleit ung Sic herh eitshi nweis eH ard ware @ 6\mod_1260180170493_21.docx @ 46720@ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 16 .10. 1/ Alle Ser ien (All gem eine Do kument e) (All gem eine Mo dule)/ Wich tige Erl äuter ungen /Sic herhei tshin weise /Gef ahr/G efahr: N icht an G erät en unter Spa nnung ar beit en! @ 6\mod_1260180365327_21.docx@ 46727@ @ 1
Do not work on components while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 16.1 0.2 / Ser ie 75 0 ( WAG O-I/O-SY STE M)/Wi cht ig e Erl äu ter ung en/Si cher hei ts- un d s onst ige H i nwei se/ Gef ahr/ Gef ahr: Einb au 0 750-x xxx nur i n Gehäus en, Sc hrän ken oder el ektri sche n Betri ebsrä umen! @ 6\mod_1260180556692_21.docx @ 4673 1@ @ 1
Installation only in appropriate housings, cabinets or in electrical operation
rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 16.1 0.3 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /G efahr /G ef ahr: U nfal l verh ütung s vorsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735@ @ 1
Pos: 16 .10.4 / All e S erie n (Al lg emei ne D o kume nte) (Allg em ein e M odul e)/ Wich tig e Er lä uter ung en/Si ch erh eits hin weis e/G ef ahr/ Gef ahr: Auf n ormg er echt e n Ansc hlu ss acht en! @ 6\mod_1260180753479_21.docx@ 46739@ @1
Pos:16.11.1/Alle Serien(AllgemeineDokumente) (Allgemeine M odul e)/Wic htig e Erläuter ung en/Sic herh eits hinwei se/Ac htung /Acht ung: De fekt e oder besc hädig te Ger äte aus tausc hen! @ 6 \mod_1260180857358_21.docx@ 46743@ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 16.1 1.2 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut erung en/Sic her heits hinwei se/Ac htung /Acht ung: G eräte vor kr ieche nden u ndis olier end en Stoff en sch ützen! @ 6\mod_1260181036216_21.docx@ 46747@ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 16.1 1.3 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /Ac htu ng/ Acht ung : Rei ni gu ng n ur mi t zul äs sig en M at erial ien! @ 6\mod_1260181203293_21.docx@ 46751@ @ 1
Cleaning only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 16.1 1.4 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /Ac htu ng/ Acht ung : K ein K o nta ktspr ay verwe nde n! @ 6\mod_1260181290808_21.docx@ 46755@ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 16.1 1.5 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /Ac htu ng/ Acht ung : V erp olung ver mei den! @ 6\mod_1260184045744_21.docx @ 46767@ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 16.1 1.6 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /Ac htu ng/ Acht ung : El e ktr ost atisc h e Ent l adu ng vermei de n! @ 6\mod_1260181364729_21.docx@ 46759@ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that you may destroy by
electrostatic discharge when you touch. Pay attention while handling the devices
to good grounding of the environment (persons, job and packing).
Pos: 17 /D oku ment ation all gemei n/ Glie der ung sel em ente /---Sei te nwec hsel--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 18 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erie n/Gerä tebes chrei bung /Gerä tebes chrei bung - Üb ersc hrift 1 @ 3\mod_1233756084656_21.docx@ 27096@ 1 @ 1
3 Device Description
Pos:19.1/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /A nwen d ung/D I/A n wen dung 750-x4 xxD I @ 3 \mod_1233762736718_21.docx@ 27108@ @ 1
The digital input module 750-402 receives control signals from digital field (e.g.
of sensors, transmitters, switches or proximity switches).
Pos:19.2/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /I/ O-Bes chr eibu ng/D I/I/ O-B eschrei bung 7 50-04xx4 DI 2-/3-Leiter ( DI, 24 V u nd 0 V) @ 6\mod_1263895132463_21.docx@ 48086@ @ 1
The I/O module has 4 input channels, providing a direct connection to two 2- or 3-
wire sensors. Two additional sensors may be connected via potential distributor.
The input signals are connected to the following CAGE CLAMP®terminals: DI 1
... DI 4, 24 V and 0 V.
Pos:19.3/Dokumentationallgemein/Gliederungselemente/------Leerzei le------ @ 3\mod_1224662755687_0.docx@ 24460@ @ 1
Pos:19.4/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Si cherh eits- und s onstig e Hinw eise/H inwei s/Hi nwei s:D I Pote ntial vervi elfäl tigung smod ule für S ensor vers orgung eins etzen @ 3\mod_1233762069125_21.docx@ 27105@ @ 1
Use field side connection modules!
Where required, use the appropriate field side connection modules for power
supply to the sensors.
Pos:19.5/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /I/ O-Bes c hrei bung / All gem ein/ Ver weis auf Kapi tel "Ansc hl üss e" @ 8\mod_1276775378035_21.docx@ 57956@ @ 1
The assignment of the connections is described in the "Connections" section.
Pos:19.6/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /I/ O-Bes c hrei bung / All gem ein/ Ver weis auf Kapi tel "Ger äte anschl i eß en" > "Ans c hlus sb eis piel( e)" @ 5\mod_1246015203281_21.docx@ 36298@ @1
Connection examples are shown in section "Connecting Devices" > "Connection
Example(s)".
Pos:19.7/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /I/ O-Bes chr eibu ng/D I/I/ O-B eschrei bung 7 50-x4xx DI RC-F ilter 3, 0 ms @ 3\mod_1233755071062_21.docx@ 27080@ @ 1
Each input channel has an RC noise rejection filter with a time constant of 3.0 ms.
Pos:19.8/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /I/ O-Bes chr eibu ng/D I/I/ O-B eschrei bung 7 50-x4xx DI H SS / positi vsch altend ( 24 V) @ 3\mod_1233831724648_21.docx@ 27231 @ @ 1
The I/O module inputs provide high-side switching. If the 24V potential for field
power is switched to an input connection, the signal status for the corresponding
input channel is set to "high."
Pos:19.9/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /LE D-A nzeige/ LED Zust and Signal @ 3\mod_1233755258578_21.docx@ 27087@ @ 1
A green LED indicates the switched status of each channel.
Pos: 19.1 0 /S erie 750 ( WAG O-I/ O-SYST EM )/G erät ebe sc hr eibu ng /Ei nleit ung /L ED-A nzei g e/Ver wei s a uf K a pitel " A nzeig eel e ment e" @ 5\mod_1246010525000_21.docx@ 36194@ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos: 19.1 1 /S erie 750 ( WAG O-I/ O-SYST EM )/G erät ebe sc hr eibu ng /Ei nleit ung /V ers org ung /V ers org ung 24 V , 0 V über Leist u ngs kont akte St andar d @ 3\mod_1226498974531_21.docx@ 25020@ @ 1
The I/O module receives the 24 V voltage supply for the field level from an
upstream I/O module or from the fieldbus coupler/controller via the power
contacts used as blade contacts. It then provides this potential to subsequent I/O
modules via the power contacts used as spring contacts.
Pos: 19.1 2 /S erie 750 ( WAG O-I/ O-SYST EM) /Wi chtig e Er l äuter ung en /Sic her hei ts- und s onstig e Hin weise/ Achtu ng/Ac htung: Maxi maler Str om Leis tungs konta kte 10 A @ 3\mod_1226499143500_21.docx@ 25029 @ @ 1
Do not exceed maximum current via power contacts!
The maximum current to flow through the power contacts is 10 A.
Greater currents can damage the power contacts.
When configuring the system, ensure that this current is not exceeded. If
exceeded, an additional potential feed module must be used.
Pos: 19.1 3 /S erie 750 ( WAG O-I/ O-SYST EM) /Wi chtig e Er l äuter ung en /Sic her hei ts- und s o nstig e H in weise /Hi nw eis/H in weis : Pot e ntial ein spei se kle mme f ür Erde einset ze n! @ 3\mod_1226499037468_21.docx@ 25023@ @ 1
Use potential feed module for Ground (earth)!
The I/O module has no power contacts for PE intake and transfer. Use a potential
feed module when a PE feed is needed for the subsequent I/O modules.
Pos: 19.1 4 /S erie 750 ( WAG O-I/O-SY ST EM) /Ger ät ebe schr ei bu ng/Ei nl eit ung/ V ersor gu ng/ Gal vani sc he T re nnu ng F el d/S ys tem @ 3\mod_1233756478750_21.docx@ 27102@ @ 1

14 Device Description WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
The field voltage and the system voltage are electrically isolated from each other.
Pos: 19.1 5 /S erie 750 ( WAG O-I/O-SY ST EM) /Ger ät ebe schr ei bu ng/Ei nl eit ung/ V ersor gu ng/ An ord nung unt er B er ücksi cht ig ung der L eis tung s kon takt e b eli ebi g @ 3\mod_1233756233468_21.docx@ 27099@ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node. An arrangement
in groups within the group of potentials is not necessary.
Pos: 19.1 6 /S erie 750 ( WAG O-I/ O-SYST EM )/G erät ebe sc hr eibu ng /Ei nleit ung /Ei ns atz ber eic h/E ins atz ber eic h 7 50-xx xx alle K oppler/ Cont roll er ohne Ei nsc hrän kung @ 3\mod_1232541691906_21.docx@26522 @ @ 1
The I/O module 750-402 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Pos: 20 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seitenwechsel---@ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 21 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erie n/Gerä tebes chrei bung /Ansic ht -Ü b ersc hrif t 2 @ 4\mod_1240984217343_21.docx@ 31958 @ 2@ 1
3.1 View
Pos: 22 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsic ht /Di gi talei ng ang s klem men /Ans ic ht 7 50-04 02 @ 9\mod_1295861125135_21.docx@ 68661@ @ 1
Figure 1: View
Pos: 23 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsic ht /A nsic ht C ag eCl a mp®_ Leg en de mit LED @ 1 5\mod_1370867188922_21.docx @ 122225 @ @ 1
Table 1: Caption acc. to figure “View”
Pos.
Description
Details see section
1
Marking possibility with
Mini-WSB
---
2
Status-LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > ”Connectors”
4
CAGE CLAMP®supplies
“Device Description” > ”Connectors”
5
Power jumper contacts
“Device Description” > ”Connectors”
6
Release tab
“Mounting” > ”Inserting and Removing
Devices”
Pos: 24 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 25 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erie n/Gerä tebes chrei bung /Ansc hlüss e -Ü bersc hrift 2 @ 4\mod_1240984262656_21.docx@ 31961@ 22@ 1
3.2 Connectors
Pos: 26 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsc hl üss e/Da te nko nta kt e/Kl em men bus - Ü bersc hrift 3 @ 6\mod_1256294684083_21.docx@ 4 3660 @ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos:27.1/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/A nsc hl üsse /Da te nkon ta kt e - F eldbu sko ppler /-c ontroll er, Ab bildung u nd Besc hreibu ng @ 3\mod_1231771259187_21.docx@ 26002@ @ 1
Communication between the coupler/controller and the I/O modules as well as the
system supply of the I/O modules is carried out via the internal bus. It is
comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data contacts
Pos: 27.2/Serie750 (WAGO-I/O-SYST EM)/ Wichti ge Erl äuter unge n/Sich erheit s- und s onsti g e Hin wei se/ Ach tung /Ac htu ng: Buskl em men ni c ht a uf G oldf eder kon ta kte l eg en! @ 7\mod_1266318463636_21.docx@ 50695@ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos:27.3/Serie750(WAGO-I/O-S YSTEM )/Wi chtig e Erlä uteru ngen/ Sicher heits- und sonstige Hinweise/Achtung/Achtung:ESD - Auf g ute Erd ung der U mgeb ung acht en! @ 7\mod_1266318538667_21.docx @ 50708 @ @1
Ensure that the environment is well grounded!
The modules are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the modules, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 28 /D oku ment ation all ge mei n/Gl ie der ungs ele me nte /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 29 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsc hl üss e/Lei st ung s kont akt e/F el dvers org u ng - Ü bersc hrift 3 @ 6\mod_1256294692864_21.docx@ 43664@ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos:30.1/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Si cherh eits- und sonst ig e Hi nwei se/ Vor sic ht/ Vors ich t: V erl etz ungsg efa hr durc h sch arf kan tig e M esser ko nta kte! @ 6\mod_1256193279401_21.docx@ 43414@ @ 1
Risk of injury due to sharp-edged male contacts!
The male contacts are sharp-edged. Handle the module carefully to prevent injury.
Pos:30.2/Serie750(WAGO-I/O-S YSTEM) /Ger ätebes chrei bung /Ansc hlüss e/Lei stung skont akte 2 LK ( Mess er/Leis tung skon takte 2 L K( Messer / Fed er) - Einl eitung @ 15 \mod_1371721641099_21.docx@123714@ @ 1
The I/O module 750-402 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as male contacts and the contacts on the right side as spring
contacts.
Pos:30.3/Serie750(WAGO-I/O-S YSTEM) /Ger äteb eschrei bung /Ansc hlüss e/Lei stung skont akte 2 LK ( Mess er/Leis tung skon takte 2 L K( Messer /Fe der) - A bbildu ng (einf ache Br eite) @ 15\mod_1367500700037_21.docx@ 118396@ @ 1
Figure 3: Power jumper contacts
Pos: 30 .4 /Ser ie 750(WAGO-I/O-SYST EM)/ Geräte besc hrei bung/A nschl üsse /Leist ungs konta kte 2 LK (M esser/ Leis tungs konta kte 2 LK (Me sser /Fed er) - Lege nde @ 15 \mod_1371721352500_21.docx@ 123710@ @ 1
Table 4: Caption acc. to view “Power jumper contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Uv) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Pos:30.5/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Si cherh eits- und s onstig e Hinw eise/ Achtu ng/A chtung :M axi maler S trom L eistung skon takt e 10 A @ 3\mod_1226499143500_21.docx@ 25029@ @ 1
Do not exceed maximum current via power contacts!
The maximum current to flow through the power contacts is 10 A.
Greater currents can damage the power contacts.
When configuring the system, ensure that this current is not exceeded. If
exceeded, an additional potential feed module must be used.
Pos:30.6/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Si cherh eits- und s onstig e Hinw eise/H inwei s/Hi nwei s: Pote ntialei nspei sekl emme für Erd e einse tzen! @ 3\mod_1226499037468_21.docx@ 25023@ @1
Use potential feed module for Ground (earth)!
The I/O module has no power contacts for PE intake and transfer. Use a potential
feed module when a PE feed is needed for the subsequent I/O modules.
Pos: 31 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 32 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsc hl üss e/CA GE CLAMP -Ansc hlüs se - Ü b ersc hrif t 3 @ 6\mod_1256296337770_21.docx@ 43674 @3 @ 1
3.2.3 CAGE CLAMP®Connectors
Pos: 33 /S erie 7 50 (WA GO-I/O-SYST EM) /Ger äteb eschr eibu ng/Ansc hl üsse/Di gital einga ngs klemme n/Ansc hlüs se 750-04xx 4DI 3-Leiter(DIn,24 V,0 V) @ 9\mod_1295861237712_21.docx@ 68665@ @ 1
Figure 4: CAGE CLAMP®Connectors
Table 5: Caption acc. to figure “CAGE CLAMP®Connectors”
Channel
Designation
Connector
Function
1
DI 1
1
Input DI 1: Signal voltage
2
DI 2
5
Input DI 2: Signal voltage
3
DI 3
4
Input DI 3: Signal voltage
4
DI 4
8
Input DI 4: Signal voltage
-
+24 V
2
Sensor supply +24 V
-
+24 V
6
Sensor supply +24 V
-
0 V
3
Sensor supply 0 V
-
0 V
7
Sensor supply 0 V
Pos: 34 /S erie 7 50 (WA GO-I/O-SYS TEM) /Wic htige Er läut erung en/Si cherh eits- unds onsti g e Hin wei se/H i nweis /Hi nw eis: D I Potent ial ver viel fäl tig ungs mod ul e für S e nsor vers org ung einse tze n @ 3\mod_1233762069125_21.docx@ 27105@ @ 1
Use field side connection modules!
Where required, use the appropriate field side connection modules for power
supply to the sensors.
Pos: 35 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 36 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erie n/Gerä tebes chrei bung /Anz eigeel ement e- Ü bersc hrift 2 @ 4 \mod_1240984390875_21.docx@ 31964@ 22 @ 1
3.3 Display Elements
Pos: 37 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nz eige ele men te /Di git alei nga ng skle mm en/ Anz eig eel em ent e 7 50-04x x 4 D I ( Agn , Bg n, Cg n, D g n) @ 9\mod_1291641003036_21.docx@ 67080@ @ 1
Figure 5: Display elements
Table 6: Caption acc. to figure “Display elements”
Channel
Designation
LED
State
Function
1 Status DI 1 A
out
Input DI 1: Signal voltage „0“
green
Input DI 1: Signal voltage „1“
2 Status DI 2 C
out
Input DI 2: Signal voltage „0“
green
Input DI 2: Signal voltage „1“
3 Status DI 3 B
out
Input DI 3: Signal voltage „0“
green
Input DI 3: Signal voltage „1“
4 Status DI 4 D
out
Input DI 4: Signal voltage „0“
green
Input DI 4: Signal voltage „1“
Pos: 38 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750
750-402 4DI 24V DC 3.0ms
Manual
Version 1.1.0
Pos: 39 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erie n/Gerä tebes chrei bung /Sch ematis ches Sc haltbi ld - Über schri ft 2 @ 4\mod_1240984441312_21.docx@ 31967@ 2 @ 1
3.4 Schematic Diagram
Pos: 40 /S erie 7 50 (WA GO-I/O-SYS TEM) /Ger ätebes chrei bung /Sche matis che Sc haltbil der/Di git aleing angs klem men/Sc hemati sch es Schal tbild 7 50-040 2 @ 9\mod_1295863706202_21.docx@ 68711 @ @ 1
Figure 6: Schematic diagram
Pos: 41 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1