GST DI-M9301 User manual

Features
Input port is provided with Class B pathway
supervision when connects with 4.7KΩ EOLR
(Part Number 3010786).
Input port can be programmed to monitor either
normally open or normally closed dry contact
input.
Input can also be programmed as
“self-answering”, which means that the Input port
monitoring is disabled, and the module will
directly send a “status” signal to FACP when the
dry-contact output changes state.
Addressable unit. Address can be programmed
in field.
Input port utilizes AD sampling technology for
precise testing.
Compatible with GST-M200 and GST-IFP4M Fire
Alarm Control Panels (FACP).
Guide rail for easy installation.
Standard: UL864, NFPA [70, 72].
Description
With a microprocessor, DI-M9301 Digital Single Input
and Output Module can communicate with fire alarm
control panel (FACP). On receiving start command
from the FACP, it will close the output relay and
illuminate the Active indicator.
Connection and Cabling
Terminals of the module are shown in Fig. 1.
Fig. 1
(Z1, Z2) IN & OUT: Connecting with the Signaling
Line Circuit (SLC) loop of FACP, polarity
insensitive.
I, G: Connecting with normally open dry contact
of an input device that closes when the device is
in alarm or changes state. It may also be set to
normally closed input by hand held programmer.
COM, NO, NC: Dry contact output terminals.
CODE: Connecting with the programmer.
Recommended Wiring: minimum 17 AWG. Subject to
local codes.
Installation
Warning:
Before installing the module, disconnect power
from the loop.
1) Before installation, make sure the enclosure is in
good condition and markings are complete.
2) The module shall either be installed in a North
America standard metal electrical box. Minimum
size is 4 in. square, 2-1/8 in depth (in this case,
standard box cover is required), or in a UL
Signaling Listed enclosure that provides
minimum wiring entries and spacing as shown on
Fig 2 and Fig 3. Minimum mounting space is
67×40.5mm.
Fig 2
DI-M9301
Digital Single Input and Output Module
Fire Alarm
Equipment
47AU
30310199 Issue 1.06

Fig. 3
3) The module can be mounted on a guide rail as
shown on Fig 4.
4) The module can also be installed in the
enclosure by 4 mounting screws as shown in
Fig.5.
Fig. 4
Fig. 5
Application
The module connects with fire control devices which
are activated by the FACP.
The address and operating mode of the module can
be programmed by a programmer in field. Please refer
to P-9910B Hand Held Programmer Installation and
Operation Manual for details.
Programming Parameters
：
In standby state of the programmer, press Fn and then
number 3, “—“will be popped up on the screen to
indicate it is in programming mode. Write a parameter
and then pressing “Program”, a “P” will show on the
screen meaning the parameter is programmed.
Press Fn and then number 3, input checking methods
can be set.
Parameters Setting
Input
1
Self-answering
2
normally-closed
Any other
numbers(Default)
normally-open
Pressing Fn and 4 can set the number of addresses.
Parameters Setting
points
2
occupies two addresses,
one for the input and one
for output
Any other
numbers(Default)
one address for both input
and output
Note: “Normally-closed” opinion can only be used for
trouble circuit, or Class E non-fire, non-emergency
input, e.g. door status sensor.
Connection of the module to field devices with
normally open dry contact is shown in Fig. 6(line
detection is provided by the controlled device).
Connection of the module to devices controlled
by 24VDC is shown in Fig.7 (line detection is
provided by the controlled equipment).
NC
I
Z2
Z1
COM
Z1
GNO
Z2
I
Z2
Z1
COM
Z1
GNO
Z2
4.7kΩ 4.7kΩ
a b
NC
Feedback
Controlled Device
Control
Input
Feedback
Control
Input
Controlled Device
DI-M9301 DI-M9301
FACP
FACP
Fig. 6
Z2
NO
G
Z1
COM
+24V
GND
Z1
Z2
I
ab
4.7kΩ
DI-M9301
NC
Z2
NO
G
Z1
COM
+24V
GND
Z1
Z2
I
4.7kΩ
NC
Controlled Device Controlled Device
DI-M9301
Power
FACP
Power
FACP
Fig. 7
30310199 Issue 1.06

Specification
Operating
Voltage
Loop 24VDC(16VDC - 28VDC)
Power Limited
Standby Current
≤0.28mA
Action Current
Loop ≤ 0.7mA
Output Capacity:
2A @ 30 VDC, 0.35PF.
Output Control
Way
Relay normally open/normally
closed contact input
Programming
Electronically addressing
Initiating circuit
maximum line
impedance
25Ωeach wire
Address Range
Two options preset by
manufacturer:
Option 1: Both Input and Output
occupy one address that ranges
from 1 to 242.
Option 2: Occupy two addresses
representing Input and Output.
Input address range is 1 to 241.
Output address is automatically
programmed as input address
plus 1.
LED
Input LED: Red. It lights in
receiving feedbacks, lights 0.5s
on, 0.5s off in input faults,and
flashes in other states.
Output LED: Red
. It lights in
relay action, turns
off in other
states.
Ingress
Protection Rating
IP30 (not tested by UL)
Operating
Temperature
0℃- +49℃
Relative Humidity
≤93%，Non Condensing
Materials of the
Enclosure
ABS, white(RAL9016)
Dimension
((L×W×H)
85.3mm×78mm×33mm （with
base
）
Weight
About 66.5g (with base)
Accessories and Tools
Model
Name
Remark
P-9910B
Hand Held
Programme
r
Supplied
separately
RY-1W-4.7k±5％
End-of-Line
Resistor
Provided
Limited Warranty
GST warrants that the product will be free from defects
in design, materials and workmanship during the
warranty period. This warranty shall not apply to any
product that is found to have been improperly installed
or used in any way not in accordance with the
instructions supplied with the product. Anybody,
including the agents, distributors or employees, is not
in the position to amend the contents of this warranty.
Please contact your local distributor for products not
covered by this warranty.
This Data Sheet is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80, Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P. R. China 066004
Tel: [phone] Fax: [phone]
[e-mail] www.gst.com.cn
30310199 Issue 1.06