GST DI-9302E User manual

30310470 Issue 1.10
Features
Input port can be programmed to monitor either
normally open or normally closed dry contact
input.
Input can also be programmed as
“self-answering”, which means that the Input port
monitoring is disabled, and the module will
directly send a “status” signal to FACP when the
dry-contact output changes state.
Addressable unit. Address can be programmed
in field.
Input port utilizes AD sampling technology for
precise testing.
Guide rail for easy installation.
Standard: EN 54-18:2005
Description
With a microprocessor, DI-9302E Digital High Voltage
Relay Module can communicate with fire alarm control
panel (FACP), control output, input circuit fault, logic
state of input signals, and state LEDs. On receiving
start command from the FACP, it will close the output
relay and illuminate the Active indicator.
Connection and Cabling
Terminals of the module are shown in Fig. 1.
Fig. 1
(Z1, Z2) IN & OUT: Connecting with Signaling
Line Circuit (SLC) loop of FACP,
polarity-insensitive.
I, G: Connecting with normally open dry contact
of an input device that closes when the device is
in alarm or changes state. It may also be set to
normally closed input by hand held programmer.
COM1,NO1,NC1,COM2,NO2,NC2: Dry contact
output terminals.
CODE: Connecting with the programmer.
TEST: Relay start test port. Press the internal
key through this hole to simulate receiving the start
command of the FACP.
Recommended Wiring: 1.0mm2or above fire cable for
all terminals. Subject to local codes.
Installation
Warning:
Before installing the module,
disconnect power from the loop.
The module should be connected to
the controlled device after passing
No-load test.
1) Before installation, make sure the enclosure is
in good condition and markings are complete.
2) The module can be mounted on a guide rail as
shown on Fig2.
3) The module can also be installed in the
enclosure by 4 mounting screws as shown in
Fig3. Minimum mounting space is 68.2×40.5mm.
Fig. 2
Fig. 3
Application
The module connects with fire control devices which
are activated by the FACP.
The address and working mode of the module can be
DI-9302E
Digital High Voltage Relay Module
2831-CPR-F2176
GST-0018-01
18
548m/08
0832-UKCA-
CPR-F0299
21

30310470 Issue 1.10
programmable by a programmer in field. Please refer
to P-9910B Hand Held Programmer Installation and
Operation Manual for details.
Programming Parameters：
In standby state of the programmer, Inputting “456”
and then pressing “Clear” button can unlock the
programmer.
In standby state of the programmer, press Fn and then
number 3, “—“will be popped up on the screen to
indicate it is in programming mode. Write a parameter
and then pressing “Program”, a “P” will show on the
screen meaning the parameter is programmed.
Press Fn and then number 3, input checking methods
and the number of address points can be set.
Parameters
Setting
Input
11
Self-answering, one address
12
normally-closed, one address
13 or other
number
normally-open, one address,
22
normally-closed, Occupies two
addresses, one for the input and
one for output.
23
normally-open, Occupies two
addresses, one for the input and
one for output.
Using GST-IFPxE series Panel, invert mode or
normal mode can be set. The operation process is as
follows:Click the setting key ( ), project settings key,
loops key in turn, select the loop and address to be set,
enter dev info interface. Then select "DI-9302E" in
spec option, and switch between “fail” and “safe”
modes in class option;
Safe mode is the normal output mode, and fail mode is
opposite to safe mode.
Connection of the module to field devices with
normally open dry contact is shown in Fig. 4.
Z2
Z1
Z1 Z2
Z2
Z1
Z1 Z2
4.7kΩ 4.7kΩ
a b
Feedback
Controlled Device
Control
Input Feedback Control
Input
Controlled Device
DI-9302E DI-9302E
FACP
FACP
I G NO1 NO2 NC1 COM1 COM2 NC2
220VAC~
I G NO1 NO2 NC1 COM1 COM2 NC2
220VAC~
Fig. 4
Notes:
It’s only applied for not more than 30VDC or
AC.
Some fire door control panel, elevator control
box has low starting current because of using
comparator, logic level. We don’t recommend that
the module is adopted due to false alarms caused
by circuit or special interference. Please add
relays between the module and the control
devices if the module is used necessarily.
The module is not used for gas extinguishing
equipment.
Accessories and Tools
Model
Name
Remark
P-9910B
Hand Held
Programmer
Supplied
separately
RT-0.25W-4.7kΩ±5％
-25mm
Resistor
Provided
Specification
Operating Voltage
Loop 24V(16V~28V)
Standby Current
≤0.34mA
Action Current
Loop ≤ 7.88mA
Output Capacity:
Capacity is 220VAC /5A.
Output Control Way
Relay normally open/normally
closed contact input
Programming
Electronically addressing
Address Range
Two options preset by
manufacturer:
Option 1: Both Input and
Output occupy one address
that ranges from 1 to 242.
Option 2: Occupy two
addresses representing Input
and Output. Input address
range is 1 to 241. Output
address is automatically
programmed as input address
plus 1.
LED
Input LED: Red. It lights in
receiving feedbacks, lights
0.5s on, 0.5s off in input faults,
flashes twice in power fault
and flashes in other states.
Output LED: Red. It lights in
relay action. It turns off in other
states.
Ingress Protection
Rating
IP30
Operating
Temperature
-10℃～+55℃
Relative Humidity
≤95%，non condensing
Materials of the
Enclosure
ABS, white(RAL9016)
Dimension(L×W×H)
92.8mm×79.2mm×46mm
Weight
About 120g
For Article33 information, please refer to the following
website：https://www.gst.com.cn/en/reacharticle33.asp
Limited Warranty
GST will repair or replace the product to the original
purchaser free of charge, if defective in materials or
workmanship during the warranty period, subject to
the terms below. GST and CRSS are not responsible
for defects or problems as a result of conditions or
applications including normal wear and tear;
catastrophe; fault or negligence of any user or any
party other than GST and CRSS; improper installation,
application, storage, maintenance, or use of products;
other causes external to products; or failure to
conform to any applicable recommendations of GST
and CRSS. In no event shall GST and CRSS be liable
for incidental, indirect, special or any other
consequential damages. To the fullest extent
permissible by law, the foregoing limited warranty is
exclusive and in lieu of all other warranties, whether
written, oral, implied or statutory. Subject to applicable
law, in no event shall the liability of GST and CRSS
exceed the purchase price of the products. NO
IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR PARTICULAR PURPOSE SHALL

E12
30310470 Issue 1.10
APPLY. Anybody, including the agents, distributors or
employees, is not in the position to amend the
contents of this warranty.
Product warnings and disclaimers
THESE PRODUCTSARE INTENDED FOR SALE TO
AND INSTALLATION BY QUALIFIED
PROFESSIONALS. CARRIER FIRE & SECURITY BV,
CARRIER FIRE & SECURITYAMERICAS
CORPORATION AND THEIR AFFILIATE
COMPANIES (TOGETHERAND EACH
INDIVIDUALLY "CARRIER") CANNOT PROVIDE ANY
ASSURANCE THATANY PERSON OR ENTITY
BUYING ITS PRODUCTS, INCLUDING ANY
“AUTHORIZED DEALER” OR “AUTHORIZED
RESELLER”, IS PROPERLY TRAINED OR
EXPERIENCED TO CORRECTLY INSTALL FIRE
AND SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-warnin
g/ or scan the following code:
This Data Sheet is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80, Changjiang East Road, ETDZ, Qinhuangdao, Hebei, P. R. China 066004
Tel: [phone]
[e-mail] www.gst.com.cn