GSWeb Playground Equipment SPACECRAFT User manual

1
SPACECRAFT MODEL NO.
GS-SC2300INSTALLATION MANUAL
SHINHEUNG ENG
1046-3, Najeon-ri, Saengnim-myeon,
Gimhae-si Gyeongsangnam-do, 621-821,
Re ublic Of Korea
Tel) +82. 55. 326. 9096~7
Fax) +82. 55. 326. 9022
E-mail) gswe[email protected]
Web site) www.gsweb21.com

2
SPACECRAFT MODEL NO.
GS-SC2300INSTALLATION & MAINTENANCE INSTRUCTIONS
Ages: 6 to 12 years
Ca acity: 25 children
Size: D: 10‘10”/ 3.30m
H: 11' 2”/ 3.40m
Use zone: D: 30' 6”/ 9.30m
Figure-1: Com leted S acecraft
Features
The Spacecraft launches the merry-go-round into the future with
a space-age look. Children love the flying-saucer design that
helps their imaginations fly into orbit. Our special bearing
system controls the rotation speed so that the children
can safely enjoy the same exhilarating experience as
a merry-go-round.
The S-SC2300 features GS Web Technology which includes
the highest steel content and the strongest connection materials
in the industry, including a steel-wire core in our edge ropes
and connection points crushed in place with over 75 tons of
pressure to ensure long life of the games and maximum safety
for the children.
S Web Rotating Climbers help bring movement, balance,
exercise and fun back into the playground.

3
SPACECRAFT MODEL NO.
GS-SC2300Safety area
6960
10620
1830
1525
3300
1525
1830
Figure-3: Safety area
Safety area
The requirements for space and safety clearances are taken from
BS-EN 1176-1 / ASTM-F1487 / CSA Z614
The use zone for stationary play equipment shall extend no less than
72 in. (1830mm) from all sides of the play structure.
Figure-2: Install
Im erial/Metric conversion:
48" = 1220mm
54" = 1370mm
60" = 1525mm
72" = 1830mm
130" = 3300mm
134" = 3400mm
274" = 6960mm
418" = 10620mm

4
SPACECRAFT MODEL NO.
GS-SC2300Foundation Layout
10620
6960
4620 ( ALVANIZED POST LEN TH)
1370
1220
1525
3300
3400
100
1830
3300
1525
1525
1830
3170 (INOX POST LEN TH)
13201950
Finished rade
Figure-4: Foundation layout
Im erial/Metric conversion:
48" = 1220mm
54" = 1370mm
60" = 1525mm
72" = 1830mm
130" = 3300mm
134" = 3400mm
274" = 6960mm
418" = 10620mm
Foundation
Measure location of game and dig a hole
5' x 5' x 4' 6" deep centered on the center
of the game.

5
SPACECRAFT MODEL NO.
GS-SC2300Overall Assembly
Figure-5: Overall Assembly
ANGLE BRACE
LOWER NET
GALVANISED POST
BASE
RING
UPPER NET
SPIDER NET
STAINLESS STEEL PAINTED POST
Overall Assembly
Assemble the arts in the following order:
1. Attach the upper net to the post head
2. Attach the ring to the net
3. Attach the spider net to the ring and the collar
4. Attach the lower net to the ring
5. Temporarially support the lower net by tying it
to the middle ring before lifting the assembly
6. Assemble base and angle braces
... cont'd next age

6
SPACECRAFT MODEL NO.
GS-SC2300
54"
60"
12"
Figure-7
Figure-6
NYLON STRING
EYE BOLT
7. Screw the eye bolt to the top of the galvanised post
8. Lift the assembly and place in the hole, inserting the post
into the pre-assembled base.
9. Level the post and fill with excavated ground
10. Install the protective surface
11. Assemble the lower ring and deck, attach to lower net.
12. Attach deck to collar on the post
13. Remove the eye bolt and install the cap
Post installation

7
SPACECRAFT MODEL NO.
GS-SC2300Aluminium ring assembly
M8 X L33 RING FIX NUT,WASHER
M8 X L55 RING FIX BOLT
12 fasteners on the to
UPPER RING
Figure-8
NYLON JOINT
Assemble the ring at the net with the nylon joint ( 1+1, 2+2, 3+3, 4+4 )
Align the o ening in the net with the ring fasteners
11
4
4
33
2
2

8
SPACECRAFT MODEL NO.
GS-SC2300Spider Net & Upper net Assembly
HALF ALUMINIUM RING
BALL JOINT
COLLAR
M10 NUT, WASHER
M10 X L35 HSCS BOLT
SPIDER NET
UPPER NET
BALL JOINT
Figure-9
Figure-10 Figure-11
Attach the ring to the u er net
Attach the s ider net to the ring and the collar

9
SPACECRAFT MODEL NO.
GS-SC2300
ALUMINIUM RING
LOWER NET
M10 X L35 HSCS BOLT, NUT,WASHER
Figure-12
Lower net assembly

10
SPACECRAFT MODEL NO.
GS-SC2300
ANGLE BRACE
M12 X L35 BOLT
M12 NUT, WASHER
M12 X L35 BOLT
BASE PLATE
M12 NUT, WASHER BASE HALF COLLAR
Figure-13
Base assembly

11
SPACECRAFT MODEL NO.
GS-SC2300
BALL JOINT
M10 X L25 HSCS BOLT
POST CAP
Remove the eye bolt
Install the ca with HSCS bolt
Cap assembly

12
SPACECRAFT MODEL NO.
GS-SC2300Parts list
1: galvanised ost
2: inox ost
3: ost ca
4: u er net
5: s ider net
6: lower net
7: aluminium ring (Φ3300)
8: nylon joint (Φ50)
9: half collar
10: eye bolt
11: M10 X L25 HSCS bolt
12: M10 X L35 HSCS bolt
13: nylon lock nut (M10),washer
11
15
3
14
2
5
7
8
9
10
12,13

13
SPACECRAFT MODEL NO.
GS-SC2300Parts list
4
14: M8 X L25 fix bolt
15: M8 X L33 fix nut,washer
16: base
17: angle brace
18: base half collar
19: M12 X L35 bolt
20: M12 nut,washer
16
17
18
19
20
1
6
2
9

14
SPACECRAFT MODEL NO.
GS-SC2300
14
Maintenance
A. General safety measures
On the playground there should be a sign(pictogram) giving the following information:
a) general emergency telephone number;
b) telephone number to contact maintenance personnel;
c) name of the playground;
d) address of playground; and
e) other relevant local information, if applicable.
The entry, exit and emergency paths to and from a playground, intended for use by the public and emergency services, should be accessible and
free of obstacles at all times.
NOTE Attention is drawn to local regulations.
B. Procedures
Defects that occur during operation and which put safety at risk should be corrected without delay. If this is not possible, the equipment should
be secured against use e.g. by immobilization or removal.
There should be written operational procedures covering the measures to be taken in the event of accidents, fire and the like.
Until unsafe equipment is repaired and released for use, access by the public should be prevented. Information about accidents brought to the
attention of the manager should be recorded on a form that includes the following details:
a) date and tie of accident;
b) age and sex of victim and clothing worn, Including footwear;
c) equipment involved;
d) number of children on site at the time of the accident;
e) description of accident;
f) injury sustained including part(s) of body affected;
g) action taken;
h) witness statements;
i) any subsequent equipment modification;
j) weather conditions; and
k) any other relevant information.

15
SPACECRAFT MODEL NO.
GS-SC2300
15
Maintenance
C. Routine maintenance
To reduce accidents, the owner or operator should ensure that an appropriate routine maintenance schedule is established, implemented and
maintained. This should take into account local conditions and the manufacturer's instructions that can affect the necessary inspection frequency.
The schedule should list the components to be maintained and should also give procedures for dealing with complaints and breakdowns.
The routine maintenance of playground equipment and surfaces should consist of preventative measures to maintain their level of safety,
performance and compliance with the relevant part(s) of EN 1176. Such measures should include:
a) tightening of fastenings;
b) re-painting and re-treatment of surfaces;
c) maintenance of any impact attenuating surfaces;
d) lubrication of bearings;
e) markig of equipment to signify loose fill finished surface level;
f) cleaning;
g) removal of broken glass and other debris or contaminants;
h) restoring loose fills to the correct level; and
i)maintenance of free space areas.
D. Corrective maintenance
Corrective maintenance should include measures to correct defects, or th re-establish the necessary levels of safety of the playground equipment
and surfaces. Such measures should include:
a) replacement of fastenings;
b) welding of welding repairs;
c) replacement of worn or defective parts; and
d) replacement of defective structural components.
E. Personal safety
Repairs during operation that could put the safety of maintenance personnel of the public at risk, should be avoided.
F. Equi ment alterations
Alterations to parts of a piece of equipment or structure that could affect the essential safety of the equipment should only be carried out after
consultation with the manufacturer or a compete person.