GSWeb Playground Equipment NET JUMPER GS-W5001 User manual

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
1
INSTALLATION MANUAL
Safety Checklist after first assembly
●Test intervals of Safety: 6 months
●Test Component and contents:
1. Removing the reticulated system:
- Check of removing condition each rope
- Screwing the turn buckle and conversion the turnbuckle
in anchors plate(see for this workstep turnbuckle assembly)
2. Abrasion condition of rope:
- Checking of all rope surface
- Strengthened of rope: Coating on the surface
3. Attachment condition of the anchors plate and turnbuckle
4. Screwing condition of all bolt
5. Galvanizing condition of the steel component:
- Protection of steel component from corrosion.
●Measure
In case of the appearance the defect detail is
repaired usually within 3 days after checking.
Caution!!
You have to construct foundation same level.
You have to keep foundation certain distance.

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
2
INSTALLATION & MAINTENANCE INSTRUCTIONS
Ages : 5 to 12 years
Capacity : 13 children
Size : D : 18‘ 5" / 5.60m
H: 4‘ 0" / 1.20m
Use zone (EN) : D : 28‘ 3" / 8.60m
Use zone (ASTM) : D : 30‘ 5" / 9.26m
▲Completed Net
Features
The series is a specialty climbing structure featuring
a flexible center area surrounded by netting. It is made of
steel-loaded Nylon cables with UV guard and the landing
surface is a textile-reinforced flexible rubber material.
The GS-W5001 features GS Web technology which includes
the highest steel content and the strongest connection materials
in the industry, including a steel-wire core in our edge ropes
and connection points crushed in place with over 75 tons
of preasure to ensure long life of the games and maximum
safety for the children.
GS Web Nets help bring movement, balance,
exercise and fun back into the playground.

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
SAFETY ZONE
(ASTM)
1,830
9,260
F.L
G.L
5,600
1,6002,4001,600
1,200 1,200
300 1,250
1,500
SAFETY ZONE
(EN)
8,600
3
Safety area and Fall Height zone
▼Fall Height and safety area
Safety area
The requirements for space and safety clearances are taken from
BS-EN 1176-1 / ASTM-F1487 / CSA Z614
The use zone for stationary play equipment shall extend no less than
72 in. (1830mm) from all sides of the play structure.
Fall Height : 1250mm (from surface)

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
4
Foundation Information
Level Line
P1
P2
Wet concrete
Dry concrete
surface layer
Finished ground
Pole
P1 = Depth below finished Grade (12" / 300mm)
P2 = Depth of concrete footing (19-2/3“ / 500mm)
▼Foundation section view
Foundation
Please refer to GS-W5001 drawing for exact installation dimensions
▲Excavate enough materials to
allow for proper depth of concrete
footings
Also ensure that there is enough space
to allow the frame to be positioned
properly.
Anchor wood support frame to ground
with pickets to prevent the frame from
moving while concrete is poured and
sets.
Finished Grade
(Optional)

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
5
Foundation Layout
▲Positioning Anchor plate on footing
Note Total distance from
front of block to front of
block is 7' 10" (2400mm)
▲Concrete footing and Anchor plate layout
1,600
500550100 250 200
500

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
6
▲Concrete footing
NOTE: Use anchor plate as guide
for exact measurements.
Assemble wooden support frames *
6 frames (5' 3" / 1600mm L x 1' 8" / 500mm W x 1' 8" / 500mm H)
*Use ½" (min) plywood; not included in package
Concrete Foundation
[Concrete]
Pour concrete* into wooden support frame until flush to top edge
Allow 3-5 days for concrete to cure before proceeding to next step
*Concrete is to be wet concrete with minimum 25 MPA / 3500PSI
Remove wood support frame from dry concrete blocks
After concrete has cured enough, remove frame and replace soil in area
around footing to subgrade level
250
190 530
200200100 30
200
150
3030

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
7
▲Attach Anchor plate to footing with flat washer, locking washer and nut
Anchor Plate Assembly
Plate Assembly
Concrete block-clean threads of "L" anchor bolts.
Attach Anchor plate to footing

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
8
Main rope Assembly
STEP-1
No. 21
Main Post Plate
STEP-2
Main rope joint
Step 1: Attach top rope with
M22 X L110 H/T BOLT as shown .
Step 2: Attach Turnbuckle to anchor plate
with M22 X L110 H/T BOLT. (at the first hole)
Loosen Turnbuckle all the way (about 100mm),
leaving only 4 or 5 threads attached
◀Attach Turnbuckle and rope
No. 23
Anchor Plate
No. 102
H/T BOLT

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
9
▲Post cap assembly
▲Post assembly
Note: Rubber mallet
may be required to
insert cap into post.
STEP-4
STEP-3
A
B
C
A B C A
Post assembly
Step 3: Attach Post Cap to Post
Step 4: Attach Post to Post base with
M22 X L70 H/T BOLT
No.101:
H/T Bolt
Post Assembly

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
(a)
(b)
(b)
(c)
(c)
(a)
10
◀Tightening Turnbuckles
It is strongly recommended that 3-4 workers lift the net into place
Attaching Turnbuckle to Anchor Plates
Tighten Rope with Turnbuckles at the Same time
Tighten Rope with Turnbuckles at the Same time
(a) + (a)
(c) + (c)
NOTE: Make sure post is level before tightening and remains level during process.
Tighten Rope with Turnbuckles at the Same time
(b) + (b)

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
11
▲Completed Net
Maintenance information
Please tighten rope with Turnbuckle properly.
If you strain the net too much, it may cause damage.
It is also recommended that subsequent checks on tension should
be carried out at monthly intervals and adjusted as required.
This will increase the overall longevity of the product.
Checking: 1 month
Refer to IPEMA and TUV maintenance system.
After Net structure tension is completed, the net will stretch
slightly over the first four weeks of use.
Following this initial period, the net needs to be
fully re-tensioned by Turnbuckle after 1 year.
Tensioning & Maintenance information

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
12
PARTS LIST
Parts check list
A. Multi Compound Rope
1. Main Post
21. Main Post Plate
23. Anchor Plate
41. L-Anchor Set
42. L-Anchor Set
61. Turn Buckle
62. Post Cap
101. H/T Bolt Set
102. H/B Bolt Set
103. U-Bolt Set No.103:
U-Bolt Set
No.62:
Post Cap
No.101:
H/T Bolt
No.102:
H/T Bolt
No.61:
Turn Buckle
No.42:
L-Anchor Set
No.41:
L-Anchor Set
No.1:
Main Post
No.A:
Multi Compound Rope
No.21:
Main post Plate
No.23:
Anchor Plate

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
13
Maintenance
A. General safety measures
On the playground there should be a sign(pictogram) giving the following information:
a) general emergency telephone number;
b) telephone number to contact maintenance personnel;
c) name of the playground;
d) address of playground; and
e) other relevant local information, if applicable.
The entry, exit and emergency paths to and from a playground, intended for use by the public and emergency services, should be accessible
and free of obstacles at all times.
NOTE Attention is drawn to local regulations.
B. Procedures
Defects that occur during operation and which put safety at risk should be corrected without delay. If this is not possible, the equipment
should be secured against use e.g. by immobilization or removal.
There should be written operational procedures covering the measures to be taken in the event of accidents, fire and the like.
Until unsafe equipment is repaired and released for use, access by the public should be prevented. Information about accidents brought to
the attention of the manager should be recorded on a form that includes the following details:
a) date and tie of accident;
b) age and sex of victim and clothing worn, Including footwear;
c) equipment involved;
d) number of children on site at the time of the accident;
e) description of accident;
f) injury sustained including part(s) of body affected;
g) action taken;
h) witness statements;
i) any subsequent equipment modification;
j) weather conditions; and
k) any other relevant information.

GSWeb Playground Equipment E-mail) gswebi[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
NET JUMPER MODEL NO.
Rev_2
2017.04
GS-W5001
14
Maintenance
C. Routine maintenance
To reduce accidents, the owner or operator should ensure that an appropriate routine maintenance schedule is established, implemented and
maintained. This should take into account local conditions and the manufacturer's instructions that can affect the necessary inspection
frequency. The schedule should list the components to be maintained and should also give procedures for dealing with complaints and
breakdowns.
The routine maintenance of playground equipment and surfaces should consist of preventative measures to maintain their level of safety,
performance and compliance with the relevant part(s) of EN 1176. Such measures should include:
a) tightening of fastenings;
b) re-painting and re-treatment of surfaces;
c) maintenance of any impact attenuating surfaces;
d) lubrication of bearings;
e) marking of equipment to signify loose fill finished surface level;
f) cleaning;
g) removal of broken glass and other debris or contaminants;
h) restoring loose fills to the correct level; and
i) maintenance of free space areas.
D. Corrective maintenance
Corrective maintenance should include measures to correct defects, or th re-establish the necessary levels of safety of the playground
equipment and surfaces. Such measures should include:
a) replacement of fastenings;
b) welding of welding repairs;
c) replacement of worn or defective parts; and
d) replacement of defective structural components.
E. Personal safety
Repairs during operation that could put the safety of maintenance personnel of the public at risk, should be avoided.
F. Equipment alterations
Alterations to parts of a piece of equipment or structure that could affect the essential safety of the equipment should only be carried out
after consultation with the manufacturer or a compete person.