GT-Lite GT-CTB-40A User manual

- When using product, basic precautions should always be followed.
- Read and follow these instructions and observe all warnings.
- Carefully read and understand the information given in this manual
before beginning installation. Failure to do so could lead to electric
shock, fire, or other injuries which could be hazardous or even fatal.
- Save these instructions and warnings.
This product may present a possible shock or fire hazard if improperly
installed or mounted. Products should be installed following these instructions,
local electrical codes, and the current National Electric Code (NEC).
- NEVER submerge this product in water!
- Do not use in on hot surfaces.
- Do not use in areas near a gas source.
- It is NOT possible to change the LED light source.
- This light is not intended for use in potentially explosive
environments. This is NOT a vapor proof light.
- This work light is NOT A TOY and is not suitable for use by children.
WARNING
CAUTION
Installation: GT-CTB-40A | 5200LM/40W LED High Lumen E26 Bulb
Installation: GT-CTB-40A | 5200LM/40W LED High Lumen E26 Bulb
This product is guaranteed against failure due to factory defects in
materials or workmanship for one (1) year from the date of purchase.
This warranty is non-transferable and applies only to the original
owner. Proof of purchase required for repair or replacement. This
warranty does not cover normal wear of parts or damage resulting from
any misuse of the product. Misuse of the product includes but is not
limited to: using in extreme weather conditions, opening the housing of
the product, or attempted remodel/alterations made to product.
- Do not look directly at the LED lights for any length of time.
- Do not shine the light directly into other people’s eyes.
EYES
Complete LED Lighting Solutions
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK,
SHUT OFF POWER BEFORE
INSTALLING OR SERVICING THIS FIXTURE
1. Turn power OFF.
2. Use a soft cloth and a mild, non-abrasive glass cleaner.
3. Lightly wipe and clean the fixture.
DO NOT use solvents.
DO NOT use cleaners containing abrasive ingredients.
NEVER spray cleaning liquid directly onto the LEDs, fixture, or wiring.
TROUBLESHOOTING GUIDE:
CLEANING INSTRUCTIONS:
Lumen: 5200LM
Watts: 40W
Equivalent to 300W Incandescent
LED Lifespan: 25,000 Hours
Operating Voltage: 120-277V AC
CRI: 80
Color Temp (CCT): 5000K Daylight
Base: E26 / Standard Edison Base
Damp Rated
Operating Temperature: -4°F to 113°F
(-20°C to 45°C)
Ballast must be bypassed if present.
Not suitable for enclosed fixtures.
Fixture does
not turn on.
Problem Probable Cause
Solution
Circuit breaker trips
or fuse blows when
light is turned on.
Bad connection.
Faulty switch.
Power is off.
Discontinue use
immediately.
Check wiring connections.
Test switch or replace it.
Verify power supply is on.
Call customer service at 1-800-865-6799
Call an electrician.

• This product is not rated for enclosed fixtures.
• DO NOT USE WITH DIMMER. This bulb is not compatible with dimmer switches.
(Using this lamp with dimmer of any kind will void the warranty.)
• Not compatible with photocell/motion sensors rated less than 150W.
• Not compatible with ballasted fixtures. Ballast must be bypassed if present.
If unsure how to retrofit MHZ/HPS light fixtures call a qualified electrician.
• Do not install this light inside of undersized enclosures.
• Do not dismantle this light. There are NO replaceable LEDs or serviceable parts.
• Do not use where exposed to water.
• Do not leave bare wires exposed outside of the electrical connections.
• Make sure wiring section is insulated.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation. Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s warranty and the authority to
operate the equipment. Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause interference to
radio communications. However, there is no guarantee that interference will or will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the following
measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a different circuit from the receiver.
4) Consult the dealer or an experienced radio/TV technician for help.
Installation: GT-CTB-40A | 5200LM/40W LED High Lumen E26 Bulb Installation: GT-CTB-40A | 5200LM/40W LED High Lumen E26 Bulb
ADDITIONAL WARNINGS:
INSTALLATION INSTRUCTIONS:
L
(Live)
N
(Neutral)
L
(Live)
N
(Neutral)
E26 CFL
E26 LED Lamp
120-277V
AC
120-277V
AC
1. Before installing the bulb, shut off power supply at the circuit breaker panel
to avoid electrical shock. Ballast must be bypassed.
It is recommended that surge/lightning protection be installed.
2. Remove old bulb.
3. Screw in new high lumen LED bulb.
4. Bulb may be mounted with the base up, down, or horizontal.
5. Restore power & turn on light switch.
Be sure to wire fixtures properly. Improper wiring greatly increases your
risk of electrical shock.