GT PARAGON DL05 User manual

120V, 650/1000W , 5.42/8.33amps
1. Cross Bars (2pcs)
2. Caster Wheels (4pcs)
3. End Caps & Nut (4sets)
4. Top Cap Flange
5. Bottom Cover
6. Flat Washer
7. Spring Washer
8. Bolt
9. Pole Assemble
10. Screw Knob
11. Inner Pole
CAUTION: DO NOT insert inner pole alone into pole
assembly. Strong spring tension may cause serious
injury during assembly / disassembly.
REMOVE ALL PACKING MATERIAL BEFORE ASSEMBLING
1. Install end caps using the nuts provided
2. Twist / push in caster wheels
3. Place the cross bars perpendicular to one another
with the caster wheels facing down
4. Place the plastic cap over the cross bars
5. Secure cross bar assembly with bottom cover using
flat washer, spring washer, and bolt. To keep the
stand from wobbling check that the bolt is securely
and tight.
6. Place the pole assembly onto the cap flange
7. Insert the inner pole into the pole assembly and
secure with screw knob.
8. Carefully place the dryer head onto the stand and
secure with screw.
DRYER SHOULD ONLY BE USED ON A STURDY FLAT
SURFACE. THE ROLLER STAND IS INTENDED TO STAND
ON THE FLOOR. DO NOT PLACE ON ELEVATED
SURFACES LIKE TABLES AND ETC.
General Operation
1. Plug unit into power source
2. Select the desired heat setting (68°-131°F)
3. The timer knob turns the unit ON/OFF (0-60min)
4. Select the desired time setting
5. Lower hood over clients head
Adjusting the Wind Volume
To adjust the wind volume, push in/out the side tab located on
the hood.
Before installing and using this unit, please carefully
read these instructions. Be sure to keep this
available for later reference.
PARAGON®
DL05 / DL05WM
HAIR DRYER
PARTS LIST - STAND
STAND ASSEMBLY
OPERATION

LITERATURE DIMENSIONS ARE FOR GENERAL
REFERENCE USE ONLY. INSTALLATION DIMENSIONS
SHOULD BE TAKEN DIRECTLY FROM THE UNIT.
GARFIELD RECOMMENDS THAT A LICENSED
CONTRACTOR AND/OR ELECTRICIAN PLAN &
PERFORM INSTALLATION.
Wall -The wall must be strong enough to support the arm
assembly and dryer head.
Recommended Height - Wall bracket should be mounted
72.5” – 76.5” from the finish floor line.
Electrical Source - An electrical source with proper power
should be prepared and located within 19” of the wall bracket.
WALL PLATE AND BRACKET SUPPORT A LARGE
LOAD. BE SURE THAT WALL PLATE BRACKET ARE
SECURELY INSTALLED.
1. Using the wall plate as a template,
drill 2 holes on the wall. You may
need a leveler to ensure that the 2
holes are straight and aligned.
2. Insert the anchor bolts (supplied).
3. Hammer the anchor pins into the anchor bolts.
4. Insert the square neck flat head bolts to the wall
plate (Fig. 4a). Attach the wall plate to the wall on
anchor bolts and affix with nuts.
5. Attach the bracket over the square neck bolts and
tighten with plastic washers, steel washers and nuts.
(Fig. 5).
6. Place the steel washer onto the stem of the wall
bracket and mount the arm assembly onto the stem
(Fig. 6).
7. Remove the hook by loosening the screw.
8. Insert the contact post into the tip of the arm
assembly. Match the grooves on the contact post to
the hook (Fig. 7).
9. Reinstall the hook into the slot and tighten firmly.
10. Attach the metal cover over the hook (Fig. 8)
11. Remove the stopper.
CAUTION: DO NOT remove stopper until machine
head is fully mounted. Strong spring tension may
cause serious injury during assembly / disassembly.
12. Connect the power cable to the electrical source.
Height Restriction (Fig. 9) If the machine head hits the
ceiling, remove metal cover and adjust the nut as shown.
Tension If the machine head drifts to the left or the right,
remove arm cover (Fig. 10). Using an allen wrench, adjust
nut (Fig. 11). “+” Increase: Turn clockwise
“-” Decrease: Turn counter clockwise
WALL MOUNT: PRE-INSTALLATION
WALL PLATE & BRACKET
ARM ASSEMBLY & MACHINE HEAD
ADJUSTMENT