Gucbir GJB13000E User manual

1
GUCBIR GENERATOR
GJB13000E / GJB13000E-3 USER MANUAL
Congratulation and thank you for your purchase our products; out aim is to provide a
high-quality generator set to achieve customer satisfaction, and we are confident that
your choice will be justified.
This manual, dealing with the generator side of the unit, gives all the basic information to
ensure satisfactory and reliable operation of your.
Please use this manual as a companion to the other manual covering the engine side.

2
Caution
1. Use SAE 10W-30 Lubrication oil. After the first oil change at 10 hours operation,
change it every 50 hours.
2. Do not connect the generator output to commercial AC outlets.
3.For information about the engine operation and maintenance, please see[IMC or
HONDA engines Owner’s Manual]

3
ⅠNAMES OF IMPORTANT PARTS AND COMPONENTS

4
MODEL
11000
11000S
13000
13000S
GENERATO
R
AC Output
50 Hz
Prime
8.5KW
8.5KW
10.5KW
10.5KW
Standby
10.5KW
10.5KW
11.5KW
11.5KW
60 Hz
Prime
10.0KW
10.0KW
12.0KW
12.0KW
Standby
11.0KW
11.0KW
13.0KW
13.0KW
Rated Speed
3000rpm(50Hz)/3600rpm(60Hz)
Phase
Single
Two line(4)
Three
Four line
Single
Two line(4)
Three
Four line
Power Factor
1.0
0.8
1.0
0.8
Excitation System
Self-Excitation System
Pole
2
Drive System
Directly Couplde to the Engine
Voltages
110/220
220/380
110/220
220/380
Voltages Regulation
±1.5% at rated rpm

5
MODEL
GX620
GX670
ENGINE
Output
Prime
16.0hp/3000rpm,18.0hp/3600pm
18.0hp/3000rpm,20.0hp/3600rpm
Standby
18.0hp/3000rpm,20.0hp/3600pm
20.0hp/3000rpm,22.0hp/3600rpm
Type
4-stroke,overhead valve,2 cylinders(900v-Twin)
Cylinder Volume
614cc
627cc
NO.of Cylinder
2
Starting System
Electric(Recoil)
Fuel Consumption
3.5L/hour
(at full load)
3.7L/hour
(at full load)
Fuel Tank Capacilty
26
26
Noise level(7m/dB)
72/50Hz, 78/60Hz
71/50Hz, 77/60Hz
Net Weight(with Wheels)
151(160)kg
157(166)kg
153(162)kg
155(160)kg
Dimensions(with wheels)
950×620×800
*Option-Voltage

6
ⅡPREPARATORY STEPS FOR OPERATION
1.ENVIRONMENTAL REQUIREMENTS
1-1.Outdoor use
A) Istall your gasotine generator unit in a dry and dustless place.
B) Avoid the direct sunshine. Place your IMC G.G.unit in the shade.
C) Keep your gasotine generator unit on a level ground so that the
unit will not move by itself. For safely, fix the unit on the ground
by pegging.

7
1-2.Indoor use
A) Use in well-ventilated areas, or vent exhaust outsids and
away from any building air intakes. A large volume of air is
required for the operation.
B) Keep the air inlet/outlet and the exhaust gas outlet 1.5m
away from any obstacle.
C) Use under 40 degrees temperature.
D) Install your IMC G.G. unit on a level surface.

8
2.PREPARATION FOR THE ENGINE
A) Check level of fuel gasoline, Lubrication OIL.
Add any of those fluids if it is below the sufficient level
specified in the Engine Owner’s Manual.
B) Check all major bolts and nuts on the engine.
Tighten any loose bolts and nuts.
3.ELECTRICAL CONNECTION WITH LOAD
A) Make sure that the load does not exceed the power
Capacity ofgasoline generator Connect electrical
Connections properly.

9
ⅢSAFETY PRECATIONS FOR SERVICING
A. Only qualified persons should test, maintain, and repair this
unit.
B. Always wear a face shield, rubber gloves and protective
Clothing when working on the unit.
C. Do not touch the generator unit or any part of load with your
bare hands or wet hands.
D. Keep hands, hair, loose clothing, and tools away from moving
parts such as fans, belts and rotors.

10
E. Do not breathe exhaust fumes.
F. Stop engine and let it cool off before checking or adding fuel.
G. Do not add fuel while smoking or if unit is near any sparks or
open flames.
H. Observe correct polarity (＋＆－)on batteries.
I. Do not tip battery.
J. Use equipment of adequate capacity to lift and support unit
and components.

11
ⅣWARM-UP PROCENDURE
A. Check all fluids daily(The unit is shipped without lub. oil).
B. Turn the fuel cock to [ON] position.
C. Set the main switch to [OFF].
D. Pull out the choke lever.
E. Turn the engine start key to [START] position.
F. Warm-up time is about 3–5minutes.

12
ⅤSTARTING –UP PROCEDURE
A. Retum speed control lever to left position.
B. Ensure voltmeter indicates normal.
(Single phase 220V)(Three phase 380V)
C. Set the main switch to [NO].
D. Observe the voltage is in the normal loaded range.

13
ⅥSTOP PROCEDURE
A. Set the main switch to [OFF]
B. Turn the engine start key to [STOP] position.
C. Close the fuel cock if the unit is in storage or transportation.

14
ⅦSIMPLIFIED TROUBLESHOOTING GUIDE
This guide is intended to give a brief information for troubleshooting with no testing or
measuring instruments to check the unit.
However, testing and measuring instruments are required to diagnose parts and compo
nents in many trouble cases.
If you cannot determine the cause by visual inspection, you should consult yout dealer
Whom you purchased this unit from.

15
ⅧMalfunctions and countermeasures
Single –phase/ Three –phase

16

17