GVS T Series User manual

Indoor Monitor
T Series - 7” Indoor Monitor User Manual_V1.0
T-IS10
User Manual

1
Content
Chapter 1 Function Overview ........................................................................................................2
Chapter 2 Product Description .......................................................................................................3
2.1 Appearance .......................................................................................................................3
2.2 Dimension ........................................................................................................................ 4
2.3 Interface Introduction .......................................................................................................5
2.4 Parameter ......................................................................................................................... 5
Chapter 3 Basic Function ...............................................................................................................6
3.1 Power-up .......................................................................................................................... 6
3.2 Call Answer ......................................................................................................................6
3.3 Function Details ............................................................................................................... 7
3.3.1 Record ................................................................................................................... 7
3.3.2 Wallpaper.............................................................................................................. 8
3.3.3 Call ........................................................................................................................9
3.3.4 Voice Message .....................................................................................................10
3.3.5 Monitor ................................................................................................................11
3.3.6 Setting ................................................................................................................. 13
Chapter 4 Installation ...................................................................................................................21
4.1 Installation Height ..........................................................................................................21
4.2 Installation Notices ........................................................................................................ 22

2
Chapter 1 Function Overview
This product is a part of the two-wire analog video door phone system. The system being
connected via 2 core wires, consists of Power Supply, Outdoor Station, and Indoor Station. The
functions and characteristics of this product are as follows:
Support visual intercom, remote unlock
Support real-time surveillance to outdoor station
Support multiple indoor monitors in one apartment
Support indoor intercom and external intercom
Support remote visual call, unlock and monitor to two-wire outdoor station via APP

3
Chapter 2 Product Description
2.1 Appearance
Touch Key Instruction:
（1）: Call/answer/end up the call;
（2）: Unlok the door.

4
2.2 Dimension

5
2.3 Interface Introduction
(1) Number ①: Two-wire bus interface;
(2) Number ②: Independent power interface (DC 21 ~ 32V);
(3) Number ③: Master/Slave monitor selection/impedance matching switch;
(4) Number ④: RS485 interface;
(5) Number ⑤: Doorbell interface.
2.4 Parameter
Working Voltage: DC 21 ~ 32V
Quiescent Current: ≤ 111mA (DC 30V)
Working current: ≤ 300mA (DC 30V)
LCD Display: 7.0 inch
Resolution: 1024×600
Dimensions (L×W×D): 179.6×179.6×25 mm
Working temperature: -10℃ ~ +55℃
Storage temperature: -30℃ ~ +70℃
①
③
②
④
⑤

6
Chapter 3 Basic Function
3.1 Power-up
Power on for the first time (bus power supply +32V or independent power supply DC +12-32V)
→ enter the Language Setting interface, select the corresponding language, click OK → enter
the main interface.
Note: If there is no operation for 1 minute in the Language Setting interface, the system
language will default to English, and enter the main interface.
3.2 Call Answer
Basic workflow: Ring bell Talk Unlock Call ended
Incoming Call:
1. Visitor can call indoor monitor from outdoor station, the bell of indoor monitor will ring;
2. Resident can click the icon to talk with the visitor;
3. During the call, the resident can unlock the door by clicking the icon . After
unlocking, call will be ended automatically within 5 seconds and return to the main interface;
4. Resident can click to end the call.
5. Calling Volume can be adjusted by the volume icon .

7
6. During the calling, you can press the icon to capture a photo of the visitor, and press
to record the current calling interface.
Attention:
(1) By default, the system automatically captures a photo of the visitor in the first 3S of the
calling. You can manually capture the photo, and the captured photo will be saved in the call
record.
(2) Support recording video after adding TF card, the default recording time of system is 15S.
(3) When the outdoor station is equipped with a second lock, you can click the icon to
unlock NO.2 lock for the visitor.
(4) Supports cloud intercom and unlocking between the bound APP account and the two-wire
outdoor station.
3.3 Function Details
This indoor monitor mainly includes six major functions: Record, Wallpaper, Call, Voice
Message, Monitor and Setting. The detailed descriptions are shown in the following.
3.3.1 Record
Record is used to store the call records of the indoor monitor. Click the icon on
the main interface to enter the Call Record interface, as shown in the figure below.

8
1. Clear: Click the Clean All button to clear all call records.
2. Delete: Select the record to be deleted, swipe left to display the delete button, and click
delete.
3. View: The user can view the latest 200 call records, click the record to view the snapshot
pictures or videos during the call, and the record can be deleted by clicking the Delete button.
3.3.2 Wallpaper
Wallpaper is used to set the background wallpaper of the indoor monitor. Click the icon
on the main interface to display the Wallpaper Setting interface, as shown
in the figure below.

9
1. Click to select the background image, and click Finish to set the selected image as the main
interface background.
2. Reset: To change the wallpaper back to the default image; Cancel: Cancel the operation and
return to the main interface.
3.3.3 Call
Call is used for initiating external intercom and indoor intercom. Click the icon
on the main interface to enter the Call interface, as shown in the figure below.
1、External Intercom
Enter the correct room number (1-200) in the input box, click the icon to call the

10
corresponding indoor monitor.
2. Call Guard Unit
Enter 200 in the input box and click the icon to call the guard unit.
3. Indoor Intercom
Click the Indoor Intercom button to make a call to another indoor monitor in the same
apartment, as shown in the figure below.
Click the icon to increase or decrease the call volume of indoor monitor, and
click to hang up the call.
3.3.4 Voice Message
Voice Message is used for users to record messages. Click the icon on the main
interface to enter the Voice Message interface, as shown in the figure below.

11
1. Record Message
Click the red button on the left to start recording → click the red button again to end; a voice
message will be generated. (Note: The max time of voice recording is 30S, and the recording
will be ended automatically when it exceeds 30S)
2. Play
Click the Play button on the right to play the current voice message.
3. Clear
Click the Clean All button to clear the current voice message list.
4. Delete
Select the message record to be deleted, swipe left to display the delete button, and click Delete.
Attention:
At present, a maximum of 30 voice messages can be recorded, and the earliest one will be
overwritten when the number reaches 30.
3.3.5 Monitor
Click the icon on the main interface to enter the Monitor interface, where you can check
the surveillance of the outdoor station, as shown in the figure below.

12
1. Monitor and Unlock
(1) Basic workflow: switch left and right to select the monitored device Monitoring
Unlock Monitoring ended
(2) During surveillance, resident can click the icon to unlock the door.
(3) Click the icon to end monitoring.
2. Surveillance Capture and video Record
(1) During the surveillance, click the icon on the screen to take a snapshot manually.
(2) During surveillance, click the icon on the screen to record the current calling
interface.
3. Call in Surveillance
(1) Basic workflow: Monitor Talk Call ended
(2) During the surveillance of the outdoor station, resident can click the icon to talk
with the visitor, and press to end the call.
Attention:
(1) Captured pictures and videos will be saved in the call log.
(2) Support recording video after adding TF card, the default recording time of system is 15S.
(3) When the outdoor station is equipped with a second lock, you can click the icon to
unlock NO.2 lock for the visitor.
4. Supports cloud intercom and unlocking between the bound APP account and the two-wire
outdoor station

13
When the bound mobile APP remotely monitors the outdoor station, the major monitor enters
the cloud intercom state and can not be operated, and those slave monitors enter the standby
state and cannot monitor the outdoor station.
3.3.6 Setting
Click the icon on the main interface to enter the setting interface, and you can set various
parameters of the indoor monitor, such as Display Setting, Warning Tone, etc.
1. Display Setting
Click the Display Setting item on the left menu bar to enter the Display Setting interface.
(1) Brightness: Slide the slider to adjust the brightness;
(2) Start screensaver(sec): Set the start time of the screensaver, which can be set as 30-255
seconds.
(3) End screensaver(min): Set the end time of the screensaver, which can be set as 1-10 minutes.
After the screen saver time expires, the system enters enters a black screen standby state.
2. Warning Tone
Click the Warning Tone item on the left menu bar to enter the Warning Tone interface.

14
(1) Ringing Volume: Slide the slider to adjust the ringing volume.
(2) Key Volume: Slide the slider to adjust the key pressing volume.
(3) Key Sound: Select the key sound.
(4) Ring: Select the ringtone.
3. Do not disturb
Click the Do not disturb item on the left menu bar to enter the Do not disturb interface.
(1) Do not disturb: Click the Do not disturb icon to mute the ringing,
(2) When there are multiple monitors in one apartment, long press the Do not disturb icon to
mute all monitors synchronously, and short press this icon to mute the current device only.
4. Language Setting
Click the Language Setting item on the left menu bar to enter the Language Setting interface.

15
(1) Language Setting: English, Italian, Spanish, French, German, Hebrew can be selected.
5. Network
Click the Network item on the left menu bar to enter the Network Setting interface.
(1) Wi-Fi switch: To turn on/off WiFi.
(2) Available Networks: Available WiFi list, click to connect the selected available WiFi.
6. Cloud Intercom Setting
Cloud Intercom Setting is mainly used to add/delete the APP account of Cloud Intercom. Click
the Cloud Intercom Setting item on the left menu bar to enter the Cloud Intercom Setting
interface.

16
(1) Add new mobile account: Click the Add new mobile account button → enter the interface
for adding a cloud intercom account, and open the Smart Home + APP to scan the QR code on
the interface.
(2) Delete mobile account: Click the Delete mobile account button → enter the account list
interface, click Unbind account → a confirmation pop-up window appears, click the Confirm
button to clear all accounts.

17
7. About
About is mainly used to view the Software Version, MCU Version, Cloud Intercom, Room
Number, Gateway, MAC, Center Server and Sip Server of the device. Click About on the left
menu bar to enter the About interface.
8. Password Setting
Password Setting is mainly used to reset the user password. Click the Password Setting item on
the left menu bar to enter the Password Setting interface.

18
Reset user password workflow:
Enter the project password, click the OK button, if the password is correct → jump to the user
password setting interface, enter the old password, new password and the confirmed new
password, click the OK button.
9. Configuration Setting
User can enter the project password (801801) to enter the Configuration Setting interface; and
enter the user password (initial user password 666666) to enter the User Setting interface.