Habey MITX-6770S-J1900 User manual

3.2 Installing Hard Drive or SSD
1. Install mSATA SSD to the mSATA slot indicated on Figure 3.
2. Install SATA hard drive or SSD by connecting the SATA power and data cable to
the connectors indicated on Figure 3.
3. Use the jumpers to select between using mSATA or standard SATA port for
SATA0 and SATA1, each port can connect to one SATA device at a time.
Figure 3: SATA and mSATA
Order Information
SKU
Description
MFG PN
MITX-6770S-J1900
Dual NIC, TPM, 7.1 Audio
2.06.0677000119
MITX-6770N-J1900
Single NIC, TPM, 7.1 Audio
2.06.0677000109 OEM
HB-6770-HDMI
DDI 2nd HDMI Add-on Card
2.04.0677011019
HB-6770-LVDS
DDI LVDS Add-on Card
2.04.0677011029
HB-POE1230
POE+ 802.3at Add-on Module
2.04.0012300009
For more information, please visit www.habeyusa.com
4
MITX-6770
Quick Setup Guide
Packing List
Description
QTY
MITX-6770 mainboard
1
I/O Shield
1
DB9 Serial cable
1
SATA Power and SATA cable
1
Safety Warning
The use and installation of this system should only be performed by professionals. Improper
installation of any electronic device or electrical component can result in serious injury or
death. Please make sure that all safety precautions are taken into account.
Static-Sensitive Devices
Electrostatic-Discharge (ESD) can damage electronic components. To avoid damaging your
system board, it is important to handle it very carefully. The following measures are generally
sufficient to protect your equipment from ESD.
Precautions
● Use a grounded wrist strap designed to prevent static discharge.
● Touch a grounded metal object before removing the board from the antistatic bag.
● Handle the board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
● When handling chips or modules, avoid touching their pins.
● Put the motherboard and peripherals back into their antistatic bags when not in use.
1

1. Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When unpacking
the board, make sure that the person handling it is static protected.
2. Memory Support
The BIS-6862 supports up to 32Gb, 2 x 260-pin SO-DIMM slot, and DDR4 2133/1600 MHz
2.1 Memory Population Guidelines
Note: Be sure to use memory modules of the same type, same speed, same frequency on the
same motherboard. Mixing of memory modules of different types and speeds is not allowed.
Figure 1: DIMM
2.2 Populating Memory Modules
1. Install the desired number of SO-DIMM into the memory slots. Pay attention to the notch
along the bottom of the module to prevent incorrect DIMM module installation.
2.Insert SO-DIMM module at the proper angle and snap it into place.
2
2.3 Installing a SO-DIMM Memory Card.
Locate the memory slot. Ensure memory is a 204-Pin SO DIMM. Align notch in memory circuit
with corresponding guide on the memory slot. Insert the memory circuit at a 45° angle and
press the circuit flat and secure it to the memory slot with an audible click on each side of the
memory slot.
3. Motherboard Installation
The MITX-6770 motherboard has standard mini-ITX mounting holes to fit different types of
chassis. Make sure that the locations of all the mounting holes for both motherboard and
chassis match. Although a chassis may have both plastic and metal mounting fasteners,
metal ones are highly recommended because they ground the motherboard to the chassis.
Make sure that the metal standoffs click in or are screwed in tightly. Then use a screwdriver to
secure the motherboard onto the motherboard tray.
Figure 2: Location of Mounting Holes
3.1 Installing the Motherboard
1. Install the I/O shield into the back of the chassis.
2. Locate the matching mounting holes on the chassis. Align the mounting holes.
on the motherboard against the mounting holes on the chassis.
3. Install standoffs in the chassis as needed.
4. Using a phillips head screwdriver, insert four Phillips head #6 screws into a
mounting holes on the motherboard and its matching mounting hole on the chassis.
3