HAD OB361 User manual

OB361 TB361
CAUTION
1. The electrical power must be disconnected from the fixture and pole before installing, servicing, or
relamping the fixture.
2. These directions must be read carefully and adhered to. Failure to do so may result in injury, damage to
the fixture, and voiding the warranty.
32001243, revision E
100 Craftway, P.O. Box 128
Littlestown, Pennsylvania 17340-0128
Phone: [phone] Fax: [phone]
INSTALLATION INSTRUCTIONS:
OB361 AND TB361 BOLLARDS
This fixture is intended for installation in accordance with the National Electrical Code and local code
specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage
to the ballast and void the warranty. These instructions do not purport to cover all details or variations in
equipment, nor to provide for every possible contingency related to installation, operation, maintenance,
or mounting situation. Should specific problems occur that are not addressed by these instructions, contact
your Sales Representative or distributor for assistance. Retain these instructions for future reference.
page 1 of 4

TOOLS REQUIRED FOR RE-LAMPING
1. 3/32" allen wrench
1. Phillips head screw driver
2. 3/32" allen wrench
TOOLS REQUIRED FOR REPLACING BALLAST
DISCLAIMER
While we believe these instructions to be accurate at the time of publication, HADCO reserves the right to make
changes to this fixture and/or components. The contractor should follow local and National Electrical Codes
where required. For any further information please contact HADCO customer service.
STEP 1: Remove the (2) #8-32 flat head screws and remove the roof.
STEP 2: Remove the lamp.
STEP 3: Loosen but don't remove (2) #8-32 pan head screws from top of ballast assembly.
STEP 4: Twist ballast assembly and pull out of bollard. Disconnect the blue quick-connects.
STEP 5: Check to make sure that the lamp type and wattage correspond to the NEW ballast
type and wattage.
STEP 6: Check the NEW ballast module for proper voltage.
STEP 7: Reconnect blue quick-connects and insert NEW ballast assembly back into bollard.
Twist keyslots onto (2) #8-32 pan head screws and tighten screws to secure ballast.
STEP 8: Replace lamp and roof.
Note: If optic louvers are used, louvers must be removed before ballast assembly can be
removed from bollard.
TOOLS REQUIRED FOR INSTALLATION
BALLAST REPLACEMENT
LAMP REPLACEMENT
NOTE: It is a good idea to clean the fixture each time you relamp. Avoid using harsh solvents
or abrasives.
STEP 1: Remove (2) #8-32 flat head screws and remove the roof.
STEP 2: Remove the old lamp and dispose of it in accordance with local codes and regulations.
STEP 3: Install a new lamp, referring to the lamp label next to the socket to ensure using the
correct type.
STEP 4: Replace the roof and insert the (2) #8-32 flat head screws.
STEP 1: Install (4) 1/2" anchor rods on a 6-8" bolt circle with 2" of each rod above the ground line.
(Use mounting template #T01000436 for anchor rod installation)
STEP 2: Using the 1/2" hex nuts & washers (supplied), assemble the mounting plate to the anchor rods.
STEP 3: Remove roof, lay bollard next to mounting plate and pull incoming power supply wires up
through top of bollard.
STEP 4: Set bollard on mounting plate and insert (4) 5/16-18 flat head screws at base.
STEP 5: Using wire nuts, connect the incoming power supply wires to the fixture supply wires coming
from the ballast assembly.
STEP 6: Insert the ballast assembly into bollard and twist keyslots onto (2) #8-32 pan head screws.
Tighten screws to secure ballast assembly.
STEP 7: Install the correct lamp as specified on the lamp label next to the socket.
STEP 8: Replace roof and insert the (2) #8-32 flat head screws.
STEP 9: Connect power and test the fixture for proper operation.
Note: If optic louvers are used, louvers must first be removed from ballast assembly, then install
the ballast assembly, replace louvers and finally install lamp.
INSTALLATION (See FIGURE 1)
WARNING - The power MUST be turned off prior to proceeding. Read these instructions carefully.
If any problems are encountered that are not covered in these instructions, contact HADCO
for assistance.
1. 3/4" wrench
2. 3/16" allen wrench
3. Wire connectors
4. Phillips head screw driver
5. 3/32" allen wrench
page 2 of 4
32001243, revision E

1/2" X 15-1/2" ANCHOR RODS
1/2" HEX NUTS (8)
WASHERS (8)
POST MOUNTING PLATE
5/16-18 FLAT-HEAD SCREWS (4)
BOLLARD POST
BALLAST ASSEMBLY
LOUVER ASSEMBLY (optional - see "Note:"
on pg.2 to install)
LAMP (by others)
CAGE
HEXAGONAL LENS (w/gasket)
ROOF
#8-32 FLAT-HEAD SCREWS (2)
2"
FIGURE 1.
(TB361 shown)
LINE
GROUND
CEMENT
page 3 of 4
32001243, revision E

OB361-ROOF(*)
TB361-ROOF(*)
OBTB361-CAGE(*)
OBTB361-LOUVERS(*)
OBTB361-LENS-REFR
OBTB361-LENS-CLR
OBTB361-LENS-OPAL
OBTB361-POST(*)
OBTB361-PLATE(*)
REPLACEMENT COMPONENTS
ROOF FOR OB361
ROOF FOR TB361
CAGE ASSEMBLY (does not include panels)
OPTIC LOUVERS (includes cast spacer)
HEXAGONAL TYPE 5 REFRACTIVE LENS (includes gasket)
HEXAGONAL CLEAR LENS (includes gasket)
HEXAGONAL OPAL LENS (includes gasket)
BOLLARD POST
POST MOUNTING PLATE
(*) = MUST SPECIFY FINISH (A-Black, B-White, G-Verde, H-Burnished Bronze, J-Green)
MEDIUM SOCKET
MEDIUM SOCKET
MEDIUM SOCKET
MEDIUM SOCKET
MEDIUM SOCKET
MEDIUM SOCKET
GX24q-3,4 SOCKET
GX24q-3,4 SOCKET
GX24q-3,4 SOCKET
MEDIUM SOCKET
(**) = MUST SPECIFY VOLTAGE (E - 120V, F - 208V, G - 240V, H - 277V, K - 347V)
(*) = MUST SPECIFY FINISH (A-Black, B-White, G-Verde, H-Burnished Bronze, J-Green)
50W HPS
70W HPS
100W HPS
50W MH (Not available in 347V)
70W MH
100W MH
26W FLUORESCENT
32W FLUORESCENT
42W FLUORESCENT
100W INCANDESCENT, 120V
OBTB361-(*)50S(**)
OBTB361-(*)70S(**)
OBTB361-(*)100S(**)
OBTB361-(*)50H(**)
OBTB361-(*)70H(**)
OBTB361-(*)100H(**)
OBTB361-(*)26F(**)
OBTB361-(*)32F(**)
OBTB361-(*)42F(**)
OBTB361-(*)100IE
REPLACEMENT BALLAST ASSEMBLIES (includes socket & ballast bracket):
page 4 of 4
32001243, revision E