Haden HW1216 User manual

www.haden.com 1
6KG & 7KG Washing Machine
HW1216 / HW1217
INSTRUCTION MANUAL

2www.haden.com
CONTENTS
Safety Instructions 3
Moving and Installing 7
Unpacking 7
Disposal of Packaging Materials 7
Removing Transit Bolts 8
Select Location 8
Adjusting Legs 9
Connecting water Inlet pipe 9
Transit Hole Plugs 10
Positioning the Water Drainage Hose 11
Electrical Connection 12
Product Overview 13
The Unit 13
Control Panel 14
Preparation 15
Preparing Laundry 15
Adding Detergent and Softener 17
Operation 19
Before First Use 19
Standard Washing 19
Other Functions 20
Programmes 21
Washing Programmes Tables 22
Maintenance 27
Cleaning 27
Troubleshooting 29
Technical Specifications 31
Guarantee 33

www.haden.com 3
SAFETY INSTRUCTIONS
When using electrical appliances, the following basic safety
precautions should always be taken.
•The appliance can be used by children aged 8 years and above and
persons with reduced physical, sensory or mental capability or a lack of
experience and knowledge if they are under supervision or have received
instruction on the safe use of the appliance and understand the hazards
involved.
•Children must not play with the appliance.
•Children younger than 3 should be kept away from the appliance unless
continuously supervised.
•Cleaning and user maintenance should not be undertaken by children
without supervision.
•If the supply cord is damaged, do not use the machine. The cable must
be replaced by the manufacturer, service agent or similarly qualified
technician to avoid a hazard.
•Only the new hose sets supplied with the appliance are to be used; old
hose sets should not be reused.
•The washing machine is for indoor use only.
•Your machine must only be installed by a competent service engineer.
•Before operating the washing machine, you must remove the transit
bolts from the rear of the machine. If the bolts are not removed, they
may cause heavy vibration, noise and malfunction of the machine which
will invalidate the guarantee.
•Install your machine in a location that is well ventilated and preferably
has constant air circulation. The openings and ventilation points of the
appliance must not be obstructed by carpet.
•Make sure that the door of your Washing Machine is not restricted and
can be opened fully.
•Ensure that the voltage and frequency of the power source are identical
to those of the washing machine.

4www.haden.com
•Do not use a plug socket with a current rating that is lower than that of
the washing machine. Never remove the power plug with wet hands.
•To ensure your safety, the plug to the power cord must be inserted into
an earthed socket.
•Do not connect your Washing Machine to the mains electricity supply
using an extension lead.
•Make sure that the water supply and electrical supply are connected by
a qualified technician in accordance with the manufacturer’s
instructions and local safety regulations.
•Please check the machine before installation. Check the outer surface
of the machine once the packaging has been removed. Do not operate
the machine if it appears damaged.
•The necessary ambient temperature for operation of your Washing
Machine is between 10 - 25 °C.
•The washing machine should not be installed in a bathroom.
•Should the ambient temperature fall below 0 °C, hoses may split or the
electronic card may not operate correctly.
•Make sure hoses and cables do not cause a trip hazard.
•Before starting any cleaning or maintenance remove the plug from the
power socket.
•A washing machine with a single inlet valve can be connected only to a
cold-water supply. A washing machine with two inlet valves can be
connected to either a hot-water or a cold-water supply.
•Make sure that all pockets are emptied before placing clothing in the
appliance.
•Sharp and rigid items such as coins, brooches, nails, coins and stones
may cause serious damage to the machine.
•Check that the water inside the drum has drained before opening the
door of the washing machine. Do not open the door if any water is
visible.
•Keep pets away from your machine.
•Pets and children may climb into the machine. Check the machine
before each use!!
•The glass door can become very hot during use. Keep children and pets
far away from the machine during use.

www.haden.com 5
•Packaging materials may be dangerous to children. Keep all packaging
(plastic bags, foam etc.) away from children.
•Only use your machine for laundry that is labelled as suitable for
washing by the manufacturer.
•Before washing clothes for the first time, it is recommended that for
your first wash you select a hot 90˚C wash cycle (without laundry) and
half fill the detergent drawer with a suitable detergent. The washing
machine should be run for the full cycle with an empty drum.
•Flammable, explosive or toxic solvents must not be used. Substances
such as gasoline and alcohol must not be used as detergents. Select
only detergents suitable for machine washing, especially drum-based
washing.
•The appliance must not be used to wash carpets.
•Be careful to avoid being burnt when the washing machine is draining
hot water.
•Never refill the water by hand during use.
•Washing laundry containing flour may damage your machine.
•Please follow the manufacturers’ instructions regarding the use of
fabric conditioner or any similar products that you intend to use in your
Washing Machine.
•After a program is complete, wait for 2 minutes to open the door.
•Remember to disconnect the water and power supply immediately after
the clothes are washed.
•Do not climb or sit on top of the machine.
•Do not lean against the door of the machine.
•Do not close the door with excessive force. If it is difficult to close the
door, reduce the amount of clothes in the drum or distribute them more
evenly.
•Never open the detergent drawer while the machine is running.
•In the event of a breakdown, unplug the machine from the mains supply
and turn the water supply off. Do not attempt to carry out any repairs.
Always contact an authorised service agent.

6www.haden.com
•Do not exceed the maximum load for the washing programme you
have chosen.
•Never force the door open when your Washing Machine is running.
•During manufacture your Washing Machine will under-go several
quality checks which may leave some water residue within the
machine. This will not affect the operation of your Washing
Machine.
•If your Washing Machine is left unused for a long time, unplug the
machine and switch off the water supply. We also recommend that
you leave the door open to prevent build-up of humidity inside.
If you need to relocate the machine:
1. Transport bolts must be reinstalled by a service engineer.
2. Accumulated water must be drained out of the machine before
relocation.
3. Handle the machine carefully. Never use protruding parts to lift the
machine. The machine door must not be used as a handle during
transportation.
4. The machine must be carried by at least 2 people.
Your machine is for domestic use only. Using it for commercial
purposes will cause your warranty to become void

www.haden.com 7
Moving and Installing
Unpack the Washing Machine
Unpack your washing machine and check that no damage has occurred
during transportation.
1.Remove the cardboard box and Styrofoam packing.
2.Lift the washing machine and remove the base
packing. Make sure that the small triangle foam
block from the base has been removed. If not, lay
the unit down on the side surface, then remove the
block from the unit bottom manually.
3.Remove the tape securing the power supply cord and drain hose.
4.Remove the accessories bag from the drum.
If the washing machine has been damaged during transportation or any
item is missing, please contact us immediately.
Dispose of Packaging Materials
The materials used to package the machine may be dangerous to children.
Please ensure that these materials cannot be accessed by children, and
dispose of them according to local regulations. Please do not throw the
packaging materials away with household waste

8www.haden.com
Remove the Transport Bolts
Before using the washing machine, the
transport bolts must
be removed from the back of the appliance.
Please remove and store the bolts as follows.
1. Loosen all bolts with a spanner before
removing them.
2. Fill the bolt holes using the with transit hole
covers
3. Store the transport bolts appropriately for
future use
Select Location
Before installing the washing machine, a location with the following
characteristics must be selected.
- A rigid, dry and level surface (if the surface is not level, please use the
guidance in the following figure, ‘Adjust Legs’, to level the appliance)
- Not in direct sunlight
- Sufficient ventilation
- Room temperature above 10℃
- Away from heat sources such as coal or gas fires.
- Leave a 20mm gap at least between the side and back of the unit.
Make sure that the power cord is not trapped beneath the washing
machine.
Do not install the washing machine on a carpeted floor.

www.haden.com 9
Adjusting Legs
For your machine to work silently and without any vibration, it should be
placed on a flat, stable surface.
There are adjustable feet under the bottom of the washing
machine. Before use, they should be adjusted so that the
washing machine is level. This will minimize vibrations and noise during
operation.
1. Check if the legs are closely attached to the cabinet. If not, please
turn them to their original positions tighten the nuts.
2. Loosen the lock nut and turn the feet until they closely contact the
floor.
3. Adjust the legs and lock them with a spanner, make sure the machine
is steady.
Connecting water inlet hose
Connect the inlet pipe as indicated.
1) Connect the straight end of the hose to
the cold water outlet at the installation
location. The outlet must be fitted with
a ¾” threaded connection.
Ensure it is tightened adequately so
that it does not leak.
1
2
3
4
Raise
Lower

10 www.haden.com
2) Connect the curved end of the hose to
the water inlet valve located at the rear
right hand top corner of the machine.
Ensure the connection is tightened
adequately so that it will not leak.
3) Make sure there a no kinks or bends in the hose.
4) Turn on the tap and check that there are no leaks from either
connection.
NOTE:
Your Washing Machine must only be connected to your water supply
using the supplied new fill hose. Old hoses must not be reused.
Transit Hole Plugs
Hole plugs can be used to plug up the
holes at the back of the machine after the
transit bolts have been removed.