Hafele dialock User manual
Re: Certification for Hafele. DT2000 Transmitter
Model: DT2000
FCC ID:PW3108
USER'S MANUAL INFORMATION
(PRELIMINARY)
The User's Manual is in preparation. The following material will be contained in the
manual:
FCC ID: PW3108
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
WARNING: Changes or modifications not expressively approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Mounting Instructions
Door Terminal Basic European version
Contents
Contents
Area of use......................................................................................3
Technical information....................................................................3
Scope of delivery.............................................................................4
Mounting.........................................................................................6
Disassambly....................................................................................20
Commissioning...............................................................................21
Brief operating instructions...........................................................22
Operation ........................................................................................ 24
Changing batteries ............................................................................ 48
Emergency opening via the profile cylinder ........................................ 51
Mounting Instructions
26
Attention!
•It is essential that you read the "Commissioning" section of these
instructions before commissioning (allocation of keys).
Area of use
The Door Terminal Basic is an electronic door fitting used principally
in the hotel sector. It is mounted on interior doors with mortise locks
acc. to DIN 18 251 and can also easily be retrofitted on the door leaf.
Depending on the design, the fixing plate on the Door Terminal Basic
can also be mounted on doors whose mortise locks deviate from DIN
18 251.
Technical information
•All Door Terminals Basic are supplied in the simple operating
mode. In this operating mode, access rights for up to 26 electronic
keys can be allocated directly at the Door Terminal Basic with a
special Programming ADD Key-stick (green). These access rights
can be withdrawn again from an authorised electronic key at the
Door Terminal Basic using a Programming DELETE Key-stick
(red). Please contact your Dialock distributor if a different operating
mode is to be selected.
•The Door Terminal Basic consists of the outer module (fixing plate
with bracket and cover) that is mounted on the outer side of the
door, and rosette fittings that are mounted on the inside of the door.
•The Door Terminal Basic has no infrared interface but can be
configured using Parameter and Special Transponders.
•The Door Terminal Basic is battery-powered, and operated using
electronic keys.
Mounting Instructions
27
Scope of delivery
4
3
1
6
5
7
9
2
2
3
10
10
8
8
Door Terminal Basic :
1
1 outer module (fixing plate with bracket and cover)
2
1 set of rosette fittings
3
2 door handles
Small parts bag:
4
1 chipboard screw, 3 x 20
5
1 retaining ring
6
1 pin, 3 x 22
7
1 pin, 4 x 22
8
2 adhesive labels (to assist mounting)
Fastening parts:
9
1 square Spindle
10
4 countersunk screws M4
The length of the fastening parts depend on the thickness of the door
leaf.
Mounting Instructions
28
Accessories (not included in the scope of delivery):
User and Programming Key-sticks
2 lithium batteries
1 release lever
1 pair of retaining ring pliers
Mounting Instructions
29
Spare parts (not included in the scope of delivery):
1
3
2
4
1
1 cover (available in a variety of colors)
2
1 bag of fastening parts
(square spindle and countersunk screws, M4)
3
1 small parts bag
4
1 fixing plate
Mounting Instructions
30
Mounting
Requirements:
•DIN mortise lock
Depending on the design of the fixing plate, it is also possible to use
mortise locks on the Door Terminal Basic that deviate from the DIN
norm (e.g. for Austria).
The length of the following Door Terminal Basic components
depends on the thickness of the door leaf and must therefore be
selected appropriately:
•the screws for attaching the rosettes
•the square spindle
Tools required and auxiliary mounting materials:
•a drilling template
•an electric drill
•drill bits suitable for the door material:
- Ø = 8 mm
- Ø = 7 mm (depending on the rosette fittings used)
- Ø = 6 mm
•a hammer
•retaining ring pliers
•a screwdriver
•a 3 mm Allen wrench
Mounting Instructions
31
Adapting the Door Terminal Basic for right-facing door handles
The Door Terminal Basic is adapted for left-or right-facing door
handles using the pins on the back of the fixing plate (with the
bracket).
1. Place the door handle on the bracket in such a way that the
direction of door handle movement is appropriate for its use.
2. Turn the external square with the door handle at its upper limit
(zero position) and hold it.
Mounting Instructions
32
R80
R
L
L80
R45
L45
3. Using a hammer, lightly tap a 3 x 22 pin into the drilled hole
labelled "R" on the back of the fixing plate. The spring of the door
handle is under pressure.
4. Insert a 4 x 22 pin in the drilled hole labelled "R45°" on the back
of the fixing plate for the door handle limit.
If the door handle angle of rotation is to be greater than 45°:
ÖInsert a 4 x 22 pin in the drilled hole labelled "R80°" on the
back of the fixing plate.
5. Secure the pins with the adhesive labels so that they do not fall
out.
Table of contents
