Haier HL32K User manual

Please READ this manual carefully before
operating your TV, and retain it for future
reference.
TFT-LCD TV
OWNER S MANUAL'
MODEL :
S
HL32K
R

2 TV LCD-TFT
Warning
RISK ELECTRIC SHOCK
DO NOT OPEN
CAUTION
!!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
!!
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the
risk of electric shock, do not perform any servicing other than that contained in the operating instructions
unless you are qualified to do so.
Important Safety Instructions
1) Read theseinstructions.
2) Keep theseinstructions.
3) Heed allwarnings.
4) Follow allinstructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do notblock any ventilationopenings. Install inaccordance with themanufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produceheat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of theobsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where theyexit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use onlywith the cart,stand, tripod, bracket, or table specified bythe manufacturer,
or sold withthe apparatus. Whena cart isused, use cautionwhen moving thecart/
Apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15)The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, suchas vases,
shall be placedon the apparatus.
16)The mains plug or appliance inlet is used as the disconnect device, remain it readily operable during the
apparatus normal use.
Class I apparatusshall be connectedto a mainssocket outlet witha protective earthingconnection.

Owner s Manual 3
Safety Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However there is no
guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to
try to correct the interference by one or more of the following measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
*Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may be not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC CAUTION:
To assure continued compliance and possible undesirable interference, the provided ferrite cores must be
used when connecting this LCD display to video equipment; and maintain at least 40cm spacing to other
peripheral device.
CANADIAN NOTICE:
This Class B digital apparatus compiles with Canadian ICES-003.
FCC STATEMENT
Energy Star compliant
By being Energy Star compliant you are assured that your Haier model is helping the environment by using less
energy while saving you money. ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and
the U.S. Department of Energy promoting energy efficiency.

SAVE THESE INSTRUCTIONS
Thank you forpurchasing the Haierproduct. This easy-to-use manual willguide you ingetting the bestuse of your
product. Remember torecord the modeland serial number. They are on label in back of the unit.
Model number
serial number
Date of purchase
Staple your receipt to your manual. You will need itto obtain warrantyservice.
4 TV LCD-TFT
Safety Instructions

Introduction
Owner s Manual 5
Contents
War ni ng . . . . . . . . .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . . .
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...........
Connection Options . . . . . . . . . . . . . . . . . . . . . .........
Universal Remote control. ............ .. . .. . .. .........
Installation
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........
Antenna Connection .. . .. . .. . ...........................
Connecting a VCR. . . . . . . . . . . . . . . . . . . . . ...........
External A/VSource Setup .. . ... . .. . ..................
Connecting a DVD player . . . . . ...... . . . . . . . . . . . . .
Connecting a DTV(digitalTV) ..............................
Connecting digital audiooutput . . . . . . . . . . . . . . . . .
Connecting a computer. . . . . . . . . . . . . . . . . . . . . . . .
Monitor Out Setup. . . . . . . . . . . . . . . . . . . . .. .. .........
HDMI and DVI input. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable sample......................................................
Connecting Headphones .. . .. . .. . .. . .. . .. . ......
Power source................ .. . .. . .. . .. . .. . .. . .. . .
Removing the tablestand and installing a
wall mount bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation
Switching On/Off the TV set . . . . . ... . . . . .. . .. . ....
Choose the MenuLanguage . .. . .........................
Choose the inputsource......................................
Channel Menu
Channel Scan............... .. . .. . .. . .. . .. . .. . .. . ..
Channel Skip....... . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding your favoritechannels to
the favorite channelslist. . . . . . . . . . . . . . . . . . . . . . .
Select the desired program. . . . . . . . . . . . . . . . . . . . .
Select the desired sound. . . . . . . . . . . . . . . . . . .. . . .
Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
6
7
8
9
9
10
11
11
12
12
13
14
14
15
16
16
17
18
18
18
19
19
20
20
20
20
Video Menu
How to selectpicture mode..................................
How to customizeyour own picturestatus .............
VGA Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..
Audio Menu
How to selectaudio mode.....................................
How to customizeyour own audiostatus ...............
SAP Broadcasts Setup.........................................
Function Menu
Menu Language...................................................
OSD Timeout.......................................................
OSD Transparency...............................................
Screen Mode.......................................................
Blue Screen.........................................................
DPMS.................................................................
Time zone setting.................................................
Date /Time setting................................................
Sleep Timersetting..............................................
DTV Caption Style................................................
Lock Menu
Parental Control ratingand categories...................
Lock setup...........................................................
Other Functions
Brief Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............
Using the Guide.. . .. . .. . .. . .. . .. . .. . .. ............
Quick program view..............................................
CC (Closed CaptionDisplay) . .. . .. . .. . .. . .... .. .
Remote Control
Setting up yourremote control ..............................
Remote Control Codes........................................
Maintenance . . ...... . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Specification . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty ............................................................
21
21
22
23
23
23

Front panel controls
This is a simplified representation of front panel.
Here shown maybe somewhat different from yourTV.
Introduction
6 TV LCD-TFT
Controls
1.MENU: Menu display.
2.INPUT: Press to open the input source mode. In the MENU/INPUT screen, these buttons serve as OK
button.
3.VOL +/-: Press to adjust the volume. In the MENU screen, these buttons serve as left/right buttons.
4.CH +/- : Press to scan through channels. To scan quickly through channels, press and hold down
either +/- . In the MENU screen, these buttonsserve as up/downbuttons.
5.POWER: Press toturn on andoff the TV.
6.AV2AUDIO IN: Connect the audio L/R cables from the video signal source to these jacks.
7.AV2 VIDEO IN: Connects the composite video cable from an external signalsource to this jack.
8.HDMI3 IN: Connect a signal from an external device to HDMI.
9.Headphone jack :Headphone audio output terminal.
10.Remote Sensor Receivers Irsignals from the remote control.
Do not putanything near thesensor ,as itsfunction may beaffected.
MENU INPUT VOL+ VOL- CH+ CH-
HL37T,HL52T
L - AUDIO - RL - AUDIO - R
HDMI3 INHDMI3 IN
VIDEO2 INVIDEO2 IN
VIDEOVIDEO
MENU INPUT VOL+ VOL- CH+ CH- POWER
HL26K, HL32K, HL37K, HL42K, HL47K
L - AUDIO - RL - AUDIO - R
HDMI3 INHDMI3 IN
VIDEO2 INVIDEO2 IN
VIDEOVIDEO

22
11
11
YYPbPb PrPr LLRR
LLLL
RRRR
VIDEOVIDEO VIDEOVIDEO
S-VIDEOS-VIDEO
VGAVGA
VGA AUDIOVGA AUDIO
AUDIOAUDIO AUDIOAUDIO
LL
RR
DVI AUDIODVI AUDIO
AUDIOAUDIO
22
LLRR
AUDIOAUDIO
COMPONENT INCOMPONENT IN
VIDEO INVIDEO IN
11
AV OUTAV OUT
VGA INVGA IN
HDMI INHDMI IN ANT INANT IN
OPTICAL OUTOPTICAL OUT
Back panel controls
Introduction
Owner s Manual 7
Connection Options
1. Digital Audio Output: Connect digital audio from various types of equipment.
NOTE: In standby mode, these ports will not work.
2. DVI Audio In: Connect a component video device to these jacks.
3. Antenna Input: Connect cable or antenna signals to the TV, either directly or through your cable box.
4. HDMI In: Connect a signal to HDMI.
5.VGA Audio In: Connect the audio L/R cables from a computer to this jack.
6.VGA Video In: Connect a video cable from a computer to this jack.
7. VIDEO In: Connects the video signal from a video device.
8. DVD/DTV In(Component ): Connect a component video device to these jacks.
9. AUDIO In: Connect to hear stereo sound from an external device.
10. S-VIDEO In: Connect S-Video out from an S-VIDEO device to the S-VIDEO input.
11. COMPONENT AUDIO In: Connect to hear stereo sound from an external device.
12. AUDIO In: Connect to hear stereo sound from an external device.
13. VIDEO Out: Connect the second TV or monitor to the TV`s AV OUT.
14. AUDIO Out: Connect to the left and right audio input jacks of your audio or video equipment.

The remote control cannot be operated unless the batteries are properly loaded.
When using the remote control, aim it at the remote sensor on the TV.
Introduction
Universal Remote control
8 TV LCD-TFT
Function introduction
NEXT DAY
PAGE-
FAV.LIST
TODAY
ADD/ERASE
PAGE+
CH.LIST
CC
P.MODE
S.MODE
FREEZE
ENU
NPUT
INFO
EXIT
R
AC
SAP
SLEEP
VOL+ CH+
Q.VIEW
OK
VO L - CH-
SELECT
DVD TV
VCR
SETBOX
CABLE AUDIO
MUTE
GUIDE
1.POWER
Press to turnon and off the TV.
2.CH.LIST
Open the channellist.
3.Shortcut Button ofInput
TODAY: Press to enterTODAYsignal;
NEXT DAY: Press to enter NEXT DAYsignal;
PAGE-: Press to enterPAGE- signal;
PAGE+: Press to enterPAGE+ signal.
4.VCR/DVD Functions
Control some videocassette recorders orDVD players.
/ Rewind / Fast / backward /Forward
Stop Play/Pause REC
5.P.MODE
Press repeatedly tocycle through theavailable picture modes.
6. CC(closed caption)
Select a closed caption.
7.GUIDE
Press to display the guide when you are watching analog or
digital channels.
8.MENU
Press to open the on-screen menu.
9.EXIT
Clears all on-screen displays and returns to TV viewing
from any menu.
10.ARC(Aspect Ratio Control)
Press to change the aspect ratio.
11. MUTE
Switches the sound on or off.
12.VOLUME UP/DOWN
Press to adjust the volume.
13.Number buttons
Press to change a channel.
14. button
Press to select digital channels. For example, to enter
“54-3”, press “54”, “ ” and “3”.
15.TV DVD VCR SETBOX CABLE AUDIO
Press the SELECT button repeatedly to select one of the
system modes in which the remote control can be used. When
the desired deviceis selected, thecorresponding LED lights
on 5 seconds.
16.ADD/ERASE
Press to add or erase a favorite program.
17.FAV.LIST
Press to open the favoritechannel list.
18.S.MODE
Press to cycle through different sound settings.
19.FREEZE
Press once todisplay a frozenimage of thecurrent program,
but audio continues.Press again toreturn to the program.
20.INPUT
Show the input source mode.
21.INFO
When you watchthe TV, press thekey, the information
display on top of the screen.
22.THUMBSTICK (Up/Down/Left/Right/OK)
Allows you tonavigate the on-screenmenus and adjust
the system settings to your preference.
23.SLEEP button
Press to display the sleep timer option.
24.SAP
Selects MTS sound: Mono, Stereo, and SAP in Analog
mode. Change the audio language in DTV mode.
25.LIGHT
Press the lightbutton, white LEDwill be ON,release this
key, white LED will be OFF.
26.CHANNEL UP/DOWN
Press to scan through channels. To scan quickly through
channels, press andhold down either+/- .
27.Q.VIEW
Press to jump back and forth between two channels.

ANT INANT IN
ANT INANT IN
Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an
outdoor antenna .
.
Over-the-air TV reception quality will depend on your antenna type, antenna
location and antenna positioning
External Equipment Connections
Antenna Connection
Multi-family Dwellings/Apartments
(Connect to wallantenna socket)
Wall Antenna
Socket
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor
Antenna
VHF Antenna
UHF Antenna
Turn clockwise to tighten
RF Coaxial Wire(75 ohm)
Bronze Wire
Be careful notto bend thebronze wire
when connecting the antenna.
Bronze Wire
To improve the picture quality in a poor signal area,
please purchase a signal amplifier and install properly.
If the antennaneeds to besplit for two TV`s, install a
2-Way Signal Splitter in the connections.
To install theantenna properly pleasecontact a
professional in your area.
Installation
Accessories
Remote control Owner`smanual Alkalinebattery(AAA) 2 Power cable
Owner s Manual 9
NEXTDAY PAGE-
FAV.LIST
TODAY
ADD/ERASE
PAGE+
CH.LIST
CC
P.MODE
S.MODE
FREEZE
ENU
NPUT
INFO
EXIT
R
AC
SAP
SLEEP
VOL+ CH+
Q.VIEW
OK
VO L - CH-
SELECT
DVD TV
VCR
SETBOX
CABLE AUDIO
MUTE
GUIDE
Please READ this manual carefully before
operating your TV,and retain itfor future
reference.
TFT-LCD TV
OWNER S MANUAL'
MODEL: S
HL26K
HL32K
HL37K
HL42K
HL47K
R
HL37T
HL52T

22
11
11
YYPbPb PrPr LLRR
LLLL
RRRR
VIDEOVIDEO VIDEOVIDEO
S-VIDEOS-VIDEO
VGAVGA
VGA AUDIOVGA AUDIO
AUDIOAUDIO AUDIOAUDIO
LL
RR
DVI AUDIODVI AUDIO
AUDIOAUDIO
22
LLRR
AUDIOAUDIO
COMPONENT INCOMPONENT IN
VIDEO INVIDEO IN
11
AV OUTAV OUT
VGA INVGA IN
HDMI INHDMI IN ANT INANT IN
OPTICAL OUTOPTICAL OUT
Installation
10 TV LCD-TFT
Connecting a VCR
NOTE: All cables shownare not includedwith the TV.
There are several ways to connect your television,
depending on the components you want to connect and
the quality of the signal you want to achieve. The
following are examplesof some different ways to connect
your TV with different input sources.
External Equipment Connections
Choose Your Connection
Toavoid picture noise(interference), leave an adequate
distance between theVCR and TV.
Connection Option 1
Set VCR output switch to channel 3 or 4 and then tune
the TV to the same channel number.
Connection Option 2
1. Connect theaudio and videocables from the VCR's
output jacks to the TV input jacks, as shown in the figure.
When connecting theTV to VCR, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red).
If you connecta S-VIDEO outputfrom VCR tothe
S-VIDEO input, the picture quality is improved;
compared to connectinga regular VCR to the Video input.
2. Insert a video tape into the VCR and press PLAY on
the VCR. (Referto the VCRowner`s manual.)
3. Select the input source with using the
INPUT button on the remote control, and
then press / button to select the source,
press OK button to confirm.

22
11
11
YYPbPb PrPr LLRR
LLLL
RRRR
VIDEOVIDEO VIDEOVIDEO
S-VIDEOS-VIDEO
VGAVGA
VGA AUDIOVGA AUDIO
AUDIOAUDIO AUDIOAUDIO
LL
RR
DVI AUDIODVI AUDIO
AUDIOAUDIO
22
LLRR
AUDIOAUDIO
COMPONENT INCOMPONENT IN
VIDEO INVIDEO IN
11
AV OUTAV OUT
VGA INVGA IN
HDMI INHDMI IN ANT INANT IN
OPTICAL OUTOPTICAL OUT
22
11
11
YYPbPb PrPr LLRR
LLLL
RRRR
VIDEOVIDEO VIDEOVIDEO
S-VIDEOS-VIDEO
VGAVGA
VGA AUDIOVGA AUDIO
AUDIOAUDIO AUDIOAUDIO
LL
RR
DVI AUDIODVI AUDIO
AUDIOAUDIO
22
LLRR
AUDIOAUDIO
COMPONENT INCOMPONENT IN
VIDEO INVIDEO IN
11
AV OUTAV OUT
VGA INVGA IN
HDMI INHDMI IN ANT INANT IN
OPTICAL OUTOPTICAL OUT
How to connect
1. Connect theDVD video outputs(COMPONENT) to
the Y Pb Pr jacks on the TV and connect the DVD audio
outputs to the YPbPr Audio IN jacks onthe TV, as
shown in the figure.
2. If your DVD onlyhas an S-VIDEOoutput jack,
connect this to the S-VIDEO inputon the TV. as shown
in the figure.
Note
If your DVD player does not have component video
output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use INPUT button on the remotecontrol to select
component mode.
3. Press Play button on external equipment for program
play.
4. Refer to the DVD player's manual for operating
instructions.
External Equipment Connections
How to connect
Connect the audio and video cables from the external
equipment's output jacks to the TV input jacks, as shown
in the figure.
When connecting theTV to external equipment, matchthe
jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).
How to use
1. Select the input source with using the INPUT button on
the remote control.
2. Press / button to select the desired source.
3. Press OK button to confirm.
4. Operate thecorresponding external equipment.
Video Game Set
Camcorder
Component Input ports
To get better picture quality, connect a DVD player to the
component input ports as shown below.
Installation
Component ports
on the TV
Video output ports
on DVD player
Y Pb Pr
Y Pb Pr
Y B-Y R-Y
Y Cb Cr
Y P P
BR
External A/V Source Setup
Connecting a DVD player
Owner s Manual 11

22
11
11
YYPbPb PrPr LLRR
LLLL
RRRR
VIDEOVIDEO VIDEOVIDEO
S-VIDEOS-VIDEO
VGAVGA
VGA AUDIOVGA AUDIO
AUDIOAUDIO AUDIOAUDIO
LL
RR
DVI AUDIODVI AUDIO
AUDIOAUDIO
22
LLRR
AUDIOAUDIO
COMPONENT INCOMPONENT IN
VIDEO INVIDEO IN
11
AV OUTAV OUT
VGA INVGA IN
HDMI INHDMI IN ANT INANT IN
OPTICAL OUTOPTICAL OUT
Digital Set-top Box
This TV can receive DigitalOver-the-air/Cable signals withoutan external digitalset-top box. However, if you do receive
Digital signals froma digital set-topbox or otherdigital external device,refer to the figure as shown below.
This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).
How to connect
Use the TV`s COMPONENT , VGA or HDMI
jack for video connections, depending on
your set-top boxconnector. Then, make
the corresponding audioconnections.
How to use
1. Turn on the digital set-top box. (Refer to the
owner`s manual forthe digital set-topbox.)
2. Use INPUT on the remote control to select
COMPONENT , VGA or HDMI source.
Send the TV`s audio to external audio equipment (stereo
system) via theDigital AudioOutput (Optical) port.
How to connect
1. Connect one end of an optical cable to the TV Digital
Audio(Optical) Outputport.
2. Connect the other end of the optical cable to the digital
audio (optical) inputon the audioequipment.
See the external audio equipment instruction manual for
operation.
Note
When connecting withexternal audio equipments,such
as amplifers orspeakers, please turnthe TV speakers off.
Connecting a digital audio output
External Equipment Connections
Connecting a DTV(digital TV)
Installation
Signal
480i
480p
720p
1080i
1080p
COMPONENT HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
HDMI
12 TV LCD-TFT
Caution: Do not look into the optical output
port. Looking at the laser beam may damage
your vision.
!!
22
11
11
YYPbPb PrPr LLRR
LLLL
RRRR
VIDEOVIDEO VIDEOVIDEO
S-VIDEOS-VIDEO
VGAVGA
VGA AUDIOVGA AUDIO
AUDIOAUDIO AUDIOAUDIO
LL
RR
DVI AUDIODVI AUDIO
AUDIOAUDIO
22
LLRR
AUDIOAUDIO
COMPONENT INCOMPONENT IN
VIDEO INVIDEO IN
11
AV OUTAV OUT
VGA INVGA IN
HDMI INHDMI IN ANT INANT IN
OPTICAL OUTOPTICAL OUT

22
11
11
YYPbPb PrPr LLRR
LLLL
RRRR
VIDEOVIDEO VIDEOVIDEO
S-VIDEOS-VIDEO
VGAVGA
VGA AUDIOVGA AUDIO
AUDIOAUDIO AUDIOAUDIO
LL
RR
DVI AUDIODVI AUDIO
AUDIOAUDIO
22
LLRR
AUDIOAUDIO
COMPONENT INCOMPONENT IN
VIDEO INVIDEO IN
11
AV OUTAV OUT
VGA INVGA IN
HDMI INHDMI IN ANT INANT IN
OPTICAL OUTOPTICAL OUT
How toconnect
1. To getthe bestpicture quality, adjustthe VGAgraphics card to 1024x768 .
2. Use theTV`s VGAor DVI (DigitalVisual Interface)AudioIN port foraudio connections, dependingon your computer
connector.
If the graphic card onthe computer doesnot output analogand digital RGBsimultaneously, connect only one of
either VGAIN or HDMI IN todisplay the VGAon theTV.
If the graphic card onthe computer doesoutput analog anddigital RGB simultaneously, set theTV toeither VGAor
HDMI ; (theother mode isset to Plugand Play automaticallyby theTV.)
3. Then,make thecorresponding audioconnection. Ifusing asound card,adjust the VGA sound as required.
How touse
1. Turnon the computerand theTV.
2. UseINPUT onthe remotecontrol toselect VGAor HDMIsource.
3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or
brightness in VGAmode. If noiseis present, changethe VGAmode to anotherresolution, change therefresh rate to
another rate oradjust the brightnessand contrast onthe menu untilthe picture isclear. Ifthe refresh rateof the VGA
graphic card cannot be changed,change the VGAgraphic card orconsult the manufacturerof theVGA graphiccard.
Note
1.Use aDVI cable.
2.Avoid keepinga fixed imageon theTV's screen fora long periodof time.The fixed image may becomepermanently
imprinted onthe screen.
3. Thesynchronization input formfor Horizontal andVertical frequenciesis separate.
Resolution
Frame
frequency
(Hz)
VGA
SVGA
XGA
640x480 60Hz
800x600 60Hz
1024x768
60Hz
Mode Resolution
External Equipment Connections
Installation
75Hz
Connecting a computer
Owner s Manual 13
75Hz

22
11
11
YYPbPb PrPr LLRR
LLLL
RRRR
VIDEOVIDEO VIDEOVIDEO
S-VIDEOS-VIDEO
VGAVGA
VGA AUDIOVGA AUDIO
AUDIOAUDIO AUDIOAUDIO
LL
RR
DVI AUDIODVI AUDIO
AUDIOAUDIO
22
LLRR
AUDIOAUDIO
COMPONENT INCOMPONENT IN
VIDEO INVIDEO IN
11
AV OUTAV OUT
VGA INVGA IN
HDMI INHDMI IN ANT INANT IN
OPTICAL OUTOPTICAL OUT
When the source device(DVD player or SetTop Box) supports HDMI
How To Connect
1. Connect thesource device toHDMI port of this TV with an HDMI cable(not supplied with this product).
2. No separatedaudio connection isnecessary.
How To Use
If the source device supports Auto HDMI function, the output resolution ofthe source devicewill be automatically
set to 1280x720p.
If the sourcedevice does notsupport AutoHDMI, you needto set theoutput resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
Select HDMI input source in input source option of Select Main source menu.
When the source device(DVD player or Set Top Box) supports DVI
How To Connect
1. Connect thesource device toHDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).
2. Aseparated audio connection is necessary.
3. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio
In port locatedon the leftside of HDMIport.
How To Use
If the source device supports Auto DVI function, the output resolution ofthe source devicewill be automatically
set to 1280x720p.
If the sourcedevice does notsupport AutoDVI, you needto set theoutput resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
Press the INPUT button to select HDMI input source in input source option of Select Main source menu.
Installation
HDMI and DVI input
14 TV LCD-TFT
External Equipment Connections
Monitor Out Setup
Connect the secondTV or monitor to the TV`s AV OUT.
See the OperatingManual of thesecond TV or monitor for
further details regardingthat device`s input settings.
YPbPr, PC, HDMI, DTV input sources cannot be used for
Monitor out.
When connecting withexternal audio equipments, such
as amplifiers orspeakers, please turn the TV speakers off.
Note
TV or Monitor

HDMI Cable
(not supplied withthe product)
HDMI to DVI Cable
(not supplied withthe product)
Analog AudioCable
(Stereo to RCA type)
(not supplied withthe product)
Installation
Cable sample
Owner s Manual 15

TO USE AC POWER SOURCE
Use the AC polarized line cord provided for
operation onAC. Insert theAC cordplug into
a standard polarizedAC outlet.
Note
Never connect the AC line cord plug to other
than the specified voltage. Use the
attached power cord only.
If the polarized AC cord does not fit into a non-
polarized AC outlet, do not attempt to file or cut
the blade. Itis the user`sresponsibility to have
an electrician replacethe obsolete outlet.
If you cause a static discharge when touching
the unit and the unit fails to function, simply
unplug the unit from the AC outlet and plug it
back in. The unit should return to normal operation.
Polarized AC Cord Plug
AC Outlet
Wider Hole
and Blade
You can connect a set of headphones to your set if you wish to watch a
TV programme withoutdisturbing the otherpeople in theroom.
Connecting Headphones
Note
Prolonged use ofheadphones at ahigh volume
may damage your hearing.
Youwill not receivesound from thespeakers
when you connectheadphones to thesystem.
Plug a setof headphones intothe 3.5mm
mini-jack socket onthe side panelof the set.
Installation
External Equipment Connections
16 TV LCD-TFT
Power source
L - AUDIO - RL - AUDIO - R
HDMI3 INHDMI3 IN
VIDEO2 INVIDEO2 IN
VIDEOVIDEO

Installation
Owner s Manual 17
Removing the table stand and installing a
wall mount bracket
Remove 4X M4 screws securing the
stand to theTV,then remove thestand.
Use 4X M6 screws to secure the wall
bracket (not supplied)to the backof your TV.
HL26K, HL32K, HL37K, HL42K, HL47K

Choose the Menu Language
When you startusing your setfor the first time, you must
select the language which will be used for displaying menus
and indications.
In the manual, the OSD (on screen display) may be
different from your TV`s, because it isjust an exampleto
help you with the TV operation.
There are several options you might need to set up in order
for your TV to workproperly. Read the instructionsthat
follow.
Initial Setup: Set according to the screen display.
Note
If the TV in power on , the screen show information
according the type of input signal . the information will
disappear. If there is no signal , No Signal will display
on the screen.
1. Choose TV Input and then press MENU button.
2. Press / button to select Function menu.
3. Press or OK button and thenuse / button to select
Language.
4. Press button to select language.
English Spanish or French
/
1 First, connect power cord correctly.
2 Select the viewing source by using INPUT button on
the remote control.
3 When finished usingthe TV, press POWER button on
the remote control.The TV reverts to standby mode.
4 If you intend to be away on vacation, disconnect the
power plug fromthe wall poweroutlet.
.
.
.
.
Change the picturesource so youcan watch your TV,
VCR, DVD, Cable, or any other devices that are
connected to yourTV.
1. Press INPUT button to enter the Select Source menu
and then use / button to select the desireditems
(TV, Video1, Video2, S-Video,Component1, Component2,
VGA, HDMI1,HDMI2,HDMI3).
2. Press OK button to confirm .
Operation
Select Source
TV
Video1
Video2
S-Video
Component1
Component2
VGA
HDMI1
HDMI2
HDMI3
Operation
Switching On/Off the TV set
Choose the Input source
18 TV LCD-TFT
Video
Audio
Channel
Lock
Function
Function
Language English
OSD Timeout Short
OSD Transparency Middle
Screen Mode Normal
Blue Screen On
DPMS On
Time Setup
Closed Caption
Default
Select
/Back
EXIT
Note
The HDMI3 optionappears only withsome models,
please see theobject.

This TV set has two methods to set channels, which are
respectively Channel Scan, Channel Skip.
In this section, how to use the remote control to set
channel is explained. You can also use buttons on the TV to
set channel.
Note
The Channel menu will be only operated in normal TV mode.
Channel menu
Operation
Owner s Manual 19
1. Press MENU button and then use / button to select
Channel menu.
2. Press or OK button to select Tuner.
3. Press button to select Cable or Antenna mode.
4. Press / button to select Channel Scan.
5. Press or OK button to start searching.
6. To cancel searching,press EXIT button.
/
Note
When Antenna is selected, the TV will detect antenna
signals and will search for antenna TV (NTSC and
ATSC) channels available in your local area.
When Cable is selected, the TV will detect cable
company supplied signalsand will searchfor cable TV
(NTSC,QAM modulated) channels available in your
Area.
Channel Scan
Channel Skip
1 Press MENU button and thenuse / button to select
Channel menu.
2 Press button and thenuse / button to select
Channel Skip.
3 Press / button to select a channel,then press OK
button to toggle between and .
.
. or OK
.
A skip channel is skipped when using CH+ and CH-
button to browse the channels. A skip channel can
be watch by key-in the channel number or select by
list.
Default un-scanned analog channels are skip.
Channel with a check icon is a skipped channel.
Status: Antenna
Analog Channels: 19
Digital Channels: 0
64%
Scanning
1
2
3
4
5
5-1
6
7
8
9
10
Analog
Analog
Analog
Analog
Analog
Digital KPIX-DT
Analog
Analog
Analog
Analog
Analog
Video
Video
Video
Video
Audio
Audio
Audio
Audio
Channel
Channel
Channel
Channel
Lock
Lock
Lock
Lock
Function
Function
Function
Function
Channel
Channel
Channel Scan
Channel Skip
Tuner Antenna
Channel Scan
Channel Skip
Tuner Antenna
Channel Scan
Channel Skip
Select
/BackScan EXITOK
Select
Select
/
/
Back
Back
Enter
Set
EXIT
EXIT
OK
OK
Cancel
EXIT

Operation
20 TV LCD-TFT
1
Also can enter channel number directly,eg:2-0.
.
Note
If skip is ON on one channel, press CH+/- button, the
channel will not appear.
2.
Using CH+/- buttons.
Press CH+ button to select a channel number in
number increasing direction.
Press CH- button to select a channel number in
number decreasing direction.
Select the desired sound
Press VOL-/+ buttons on the remote or the front of the
TV set to adjust the volume level. The range is 0~100.
When the volume buttons are pressed the volume level
is displayed automatically on the TV screen.
Mute
When you need to pay attention to , or
there is atelephone calling youor there aresome
guests visiting you, the sound elimination (mute)
function is veryconvenient.
a conversation
1 Press MUTE button on the remote control and
type face will display on the screen. At this time, the
sound of theTV set is turned off.
2 If you want to recover the sound, press MUTE
button again ordirectly press VOL+ button.
.
.
Volume
Select the desired program
Adding your favorite channels
to the favorite channels list
Toadd your favoritechannels to thefavorite
channels list:
1 Press CH+/- buttons to select a channel.
2 Press ADD/ERASE button to add the channel to your
favorite channels list.
3 Press ADD/ERASE button again to delete the channel.
To tune to a favorite channel:
1 Press FAV.LIST to open yourfavorite channels list.
2 Press / button to selecta channel onthe list.
3 Press OK. Your TV tunes to that channel.
.
.
.
.
.
.