Haier QVM7167RN User manual

31-7000110 Rev.1 06-20 GEA
English/Spanish
InstallationInstructions
OvertheRangeMicrowaveOven
Ifyouhavequestions,visitourwebsite at:haierappliances.com.
READ CAREFULLY
KEEP THESE INSTRUCTIONS
BEFOREYOUBEGIN
Readtheseinstructionscompletelyandcarefully.
ReadandobserveallWARNINGSandCAUTIONSshown
throughouttheseinstructions.
IMPORTANT– Observeallgoverningcodesandordinances.
•NotetoInstaller–Besuretoleavetheseinstructionsfor
theconsumer’sandlocalinspector’suse.
•NotetoConsumer –Keeptheseinstructionswithyour
Owner’sManualforfuturereference.
•Skill Level –Installationofthisappliancerequiresbasic
mechanicalandelectricalskills.
Proper installation is the responsibility of the installer.
Productfailureduetoimproperinstallationisnotcovered
undertheHaierAppliancesWarranty.SeeWarranty
information.
•CompletionTime–1to3 Hours.Newinstallationsrequire
moretimethanreplacementinstallations.
Careshouldbeexercisedwhentheapplianceisinstalledor
removed,toreducethelikelihoodofdamagetothepower
supplycord.
Ifyoureceivedadamagedappliance,youshould
immediatelycontactyourdealerorbuilder.
ModelNumber:QVM7167

231-7000110 Rev.1
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
Aqualifiedelectricianmust performa ground
continuitycheckon thewall receptaclebefore
beginningtheinstallationtoensurethatthe outletbox
isproperlygrounded.If notproperlygrounded, orif the
wallreceptacledoes notmeet electricalrequirements
noted (underELECTRICALREQUIREMENTS),a
qualified electricianshould beemployedtocorrectany
deficiencies.
Risk of Electric Shock.
Can cause injury or
death: Remove house
fuse or
open circuit breaker
before beginning
installation to avoid
severe or fatal shock
injury.
Risk of Electric Shock.
Can cause injury or
death: THIS APPLIANCE
MUST BE PROPERLY
GROUNDED to avoid
severe or fatal shock.
The power cord of
this appliance is equipped with a three-prong
(grounding) plug which mates with a standard
three-prong (grounding) wall receptacle to minimize
the possibility of electric shock hazard from this
appliance.
Where a standard two-prong wall receptacle is
encountered, it must be replaced with a properly
grounded three-prong wall receptacle, installed by a
qualified electrician.
Ensure
proper
ground
existsbefore
use
FORYOURSAFETY:
For personalsafety,
themountingsurfacemustbe
capableofsupportingthecabinetload,inadditionto
theaddedweightofthis63–85poundproduct,plus
additionalovenloadsofupto50poundsoratotalweight
of113–135pounds.
For personalsafety,thisproduct
cannotbeinstalledincabinet
arrangementssuchasanislandor a peninsula.Itmustbe
mountedtoBOTHatopcabinetANDawall.
To avoid therisk of personal
injury(backinjuryorotherinjuries
duetoexcessiveweightofthemicrowaveoven)or
propertydamage,youwillneedtwopeopletoinstallthis
microwaveoven.
Thisisthesafetyalertsymbol.Thissymbolalertsyoutopotentialhazardsthatcankillorhurtyouandothers. All
safetymessageswillfollowthesafetyalertsymbolandtheword“DANGER”,“WARNING”,or“CAUTION”. Thesewords
aredefinedas:
DANGER
Indicatesahazardoussituationwhich,ifnotavoided,willresultindeathorseriousinjury.
WARNING Indicatesahazardoussituationwhich,ifnotavoided,couldresultindeathorseriousinjury.
CAUTION Indicatesahazardoussituationwhich,ifnotavoided,couldresultinminorormoderateinjury.
ELECTRICAL REQUIREMENTS
Productratingis120 voltsAC,60Hertz,14.5 amps
and1.7kilowatts.Thisproductmustbe connectedto a
supplycircuitoftheproper voltageand frequency. Wire
sizemust conformtotherequirementsof theNational
ElectricalCodeorthe prevailinglocal codeforthis
kilowatt rating.Thepowersupply cordandplug should
bebroughtto aseparate 15-to20-amperebranch
circuitsingle grounded outlet.The outletboxshould
belocatedin thecabinet abovethe microwaveoven.
Theoutletboxandsupplycircuitshouldbe installed
bya qualified electricianand conformtothe National
ElectricalCodeorthe prevailinglocal code.
CAUTION
CAUTION
CAUTION
RISKOFELECTRICSHOCK
Can cause injuryor death:DO
NOT, underanycircumstances,
cut,deformor removeany of
the prongs from the powercord.Do not usewith an
extensioncord.Failuretocomplymaycausefire.
WARNING
WARNING
WARNING

31-7000110 Rev.1 3
Installation Instructions
HOOD EXHAUST
Thefollowingchartdescribes anexampleof onepossible
ductworkinstallation.
NOTE:Readthesenexttwopagesonlyifyouplantoventyourexhausttotheoutside.Ifyouplantorecirculatetheairbackinto
theroom,proceedtopage11.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
NOTE:Forback exhaust,careshould betakentoalignexhaustwith space betweenstuds,or wallshould
bepreparedat thetime itis constructed byleavingenough space betweenthewall studsto accommodate
exhaust.
*IMPORTANT: If arectangular-to-roundtransitionadaptorisused, thebottom cornersofthe damper
willhave to becut to fit, usingthe tinsnips,inorderto allowfreemovementof thedamper.
Thefollowingchartdescribesanexampleofonepossible
ductworkinstallation.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
EQUIVALENT NUMBER
DUCT PIECES LENGTH x USED = LENGTH
RoofCap 24Ft. x (1) = 24Ft.
12Ft. StraightDuct 12Ft. x (1) = 12Ft.
   ¤&ėÛòøñç¥
Rectangular-to-Round 5 Ft. x (1) = 5Ft.
TransitionAdaptor*
Equivalentlengthsofductpieces arebased onactual testsand
reflectrequirementsforgoodventing performancewith anyvent hood.
Total Length = 41 Ft.
EQUIVALENT NUMBER
DUCT PIECES LENGTH* x USED = LENGTH
WallCap 40Ft. x (1) = 40Ft.
3Ft. StraightDuct 3Ft. x (1) = 3Ft.
(31\4ėû! ėÛèæ÷äñêøïäõ¥
90°Elbow 10Ft. x (2) = 20 Ft.
Equivalentlengthsofductpieces arebased onactual testsand
reflectrequirementsforgoodventing performancewith anyvent hood.
Total Length = 63 Ft.

431-7000110 Rev.1
Installation Instructions
EQUIVALENT NUMBER
DUCT PIECES LENGTH x USED = LENGTH
Rectangular-to-Round 5Ft. x ( ) = Ft.
TransitionAdaptor*
WallCap 40Ft. x ( ) = Ft.
90°Elbow 10Ft. x ( ) = Ft.
45°Elbow 5Ft. x ( ) = Ft.
90°Elbow 25Ft. x ( ) = Ft.
45°Elbow 5Ft. x ( ) = Ft.
RoofCap 24Ft. x ( ) = Ft.
   Ü÷õäìêë÷Íøæ÷&ėÛòøñçòõ !Ï÷  û ¤¥    Ï÷
3
1\4ėû! ėÛèæ÷äñêøïäõ
Total Ductwork = Ft.
Equivalentlengths of duct pieces are based on actual tests
andreflect requirements for good venting performance with
anyvent hood.
*IMPORTANT: Ifarectangular-to-roundtransition
adaptorisused, the bottomcornersofthe
damperwill havetobecuttofit,usingthetinsnips,
inordertoallowfreemovement of the damper .
NOTE: Ifyouneedtoinstall ducts,notethatthe total duct
lengthof31\4ėû! ėõèæ÷äñêøïäõòõ&ėçìäðè÷èõõòøñççøæ÷
should not exceed 140 equivalent feet.
Øø÷öìçèùèñ÷ìïä÷ìòñõèôøìõèöäÑØØÍÎáÑÊÞÜÝÍÞÌÝ
Readthe following carefully.
NOTE: Itis important thatventingbeinstalled using
themostdirect routeandwith asfewelbowsas possible.
Thisensuresclearventingofexhaustand helpsprevent
blockages.Also, make sure dampers swing freely and
nothing is blocking the ducts.
Exhaust connection:
Thehoodexhausthasbeen designedtomatewith
astandard31\4ėû! ėõèæ÷äñêøïäõçøæ÷
Ifaround ductis required,a rectangular-to-round
transitionadaptormustbe used.Do not use less than
a 6ėdiameter duct.
Maximum duct length:
Forsatisfactory airmovement,the totalduct lengthof
31\4ėû! ėõèæ÷äñêøïäõòõ&ėçìäðè÷èõõòøñççøæ÷should
not exceed 140 equivalent feet.
Elbows, transitions, wall and roof caps, etc.,
presentadditional resistanceto airflowandareequivalent
to asection ofstraightductwhich islonger thantheir
actualphysical size.When calculatingthe totalduct
length,addtheequivalentlengthsof alltransitionsand
adaptorsplusthe lengthof allstraightductsections.The
chart belowshowsyouhowto calculate totalequivalent
ductworklength usingthe approximatefeetof equivalent
lengthofsometypicalducts.

31-7000110 Rev.1 5
PARTS INCLUDED
Youwill findtheinstallation hardwarecontainedin a
packetwith theunit. Checktomakesureyouhaveall
theseparts.
NOTE: Someextrapartsareincluded.
HARDWARE PACKET
ADDITIONAL PARTS
Installation Instructions
DAMAGE – SHIPMENT INSTALLATION
•If the unit is damaged in shipment, returnthe unit
to thestorein whichit wasbought forrepairor
replacement.
•If the unit is damaged by the customer, repairor
replacement isthe responsibilityof thecustomer.
•If the unit is damaged by the installer (ifother than
thecustomer),repairorreplacement mustbemade
byarrangementbetweencustomerand installer.
Part Quantity
Woodscrews(1/4”x2”) 2
Togglebolts(andwind
nuts)(3/16”x3”) 2
Self-aligningmachine
screws(1/4”-28x3
1/4”)
2
NylonGrommet(for
metalcabinets) 1
Tappingscrews(for
attachingthedamper
ductconnector)
3
Onepowercordclamp
andOnedark-colored
mountingscrew(tohold
thepowercord)
1
Part Quantity
TopCabinet
Template 1
RearWall
Template 1
Installation
Instructions 1
Separately
PackedGrease
Filter
2
MountingPlate
(forsupporting
themicrowave
Oven)
1
Coverplate(for
RoomVenting
installation)
1

631-7000110 Rev.1
Installation Instructions
TOOLS YOU WILL NEED
#1and#2Phillips
screwdriver Pencil
Rulerortape measureand
straightedge
Carpenter square
(optional)
Tinsnips (forcutting
damper,if required)
Electricdrill with3\16ė7\16ė
1\2ėäñç5\8ėçõìïïåì÷ö
Hammer(optional)
Studfinder
Fillerblocks orscrapwood
pieces,if neededfortop
cabinetspacing (usedon
recessedbottomcabinet
installationsonly)
Gloves Saw(saber,hole or keyhole)
Level Duct and masking
tape
Scissors (tocut
template,ifnecessary)
Safetygoggles
MOUNTINGSPACE NOTES:
•Ýëèöóäæèåè÷úèèñ÷ëèæäåìñè÷öðøö÷åè# ėúìçèäñç
freeof obstructions.
•Thisovenis forinstallation overrangesup to
#&ėúìçè
•Ifthespace betweenthe cabinetsis greaterthan30”,a
FillerPanel Kitmaybeused tofillinthe gapbetweenthe
microwaveoven andthe cabinets. Your Owner’sManual
contains thekit numberforyourmodel.
•Ifyouare goingtoventyouroventothe outside,see
HoodExhaustSection forexhaustduct preparation.
•When installingthe ovenbeneath smooth,flat cabinets,
becarefulto followtheinstructionson thetopcabinet
templateforpowercord clearance.
• * 13”max: forstandard installation, 15” cabinetdepth
requires additional stepsusing an additionalinstallation
kitJX15BUMPWW/BB.
•Formodelswithtopventingholes: Donotallowcabinetry
orotherobjectstoblocktheairflowofthevent.
•Haiermicrowavesshouldnotbeinstalledoveranycooktop
orrangewithacombinedBTUgreaterthan60,000BTU.
Backsplash
&&ėòõðòõè
fromthe floor
to thetopof
theoven
# ė
2ė
# ė
min.
16-1\2ė
Bottomedge of
cabinetneeds
÷òåè# ėòõ
morefromthe
cooking surface
!#ėðäû

31-7000110 Rev.1 7
Findthestuds,using oneof thefollowing
methods:
A. Studfinder–a magneticdevice which
locates nails. OR
B.Useahammertotaplightly acrossthe
mountingsurfacetofind asolid sound.
Thiswillindicate astudlocation.
After locatingthe stud(s),find thecenterby
probingthe wallwitha smallnail tofindtheedges
ofthestud.Thenplacea markhalfwaybetweenthe
edges.The centerofanyadjacentstudsshould be
!&ėòõ"$ėéõòð÷ëìöðäõî
Draw aline downthe centerofthe studs.
THE MICROWAVE MUST BE CONNECTED TO
AT LEAST ONE WALL STUD.
1
Removethe installationinstructions,filters,glass
tray,mounting plate, andthe smallhardwarebag.
Donotremove thefoamprotectingthefrontofthe
oven.
Foldback all4 cartonflaps fullyagainst cartonsides.
Thencarefullyrollthe ovenandcartonoverontothe
top side.The ovenshouldbe restingin thefoam.
REMOVING THE MICROWAVE
OVEN FROM THE CARTON
FINDING THE WALL STUDS
B.
A.
2
PLACEMENT OF THE MOUNTING PLATE
1
Wall
Studs
Center
3
Carton
Pullthe cartonupand offthe oven.
foam
Installation Instructions
2
3
Settheovenupright. Removeandproperlydiscard
plasticbagsandfoampacking.
4
1

831-7000110 Rev.1
Installation Instructions
DETERMINING MOUNTING PLATE LOCATION UNDER YOUR CABINET
C
Plate Position – beneath flat bottom
cabinet Plate Position – beneath framed recessed cabinet bottom
3
2
Drawaverticallineonthewallatthecenterofthe
30”space.
TapetheRearWallTemplateontothewallmatching
thecenterlineandtouchingthebottomcabinet
frame.
30”toCooktop
Plate Position – beneath recessed bottom
cabinet with front overhang.
30”toCooktop
Drawalineonthe
backwallequaltothe
depthofthefront
overhang
Yourcabinetsmayhavedecorativetrimthatinterferes
withthemicrowaveinstallation.Removethedecorative
trimtoinstallthemicrowaveproperlyandtomakeit
level.
THEMICROWAVEMUSTBELEVEL
Usealeveltomakesurethecabinetbottomislevel.
Ifthecabinetshaveafrontoverhangonly,withnoback
orsideframe,installthemountingplatedownthesame
distanceasthefrontoverhangdepth.Thiswillkeepthe
microwavelevel.
Measuretheinsidedepthofthefrontoverhang.
Drawahorizontallineonthebackwallanequal
distancebelowthecabinetbottomastheinsidedepth
ofthefrontoverhang.
Forthistypeofinstallationwithfrontoverhangonly,
aligntheRearwallTemplatewiththishorizontalline,
nottouchingthecabinetbottomasdescribedinStep
D.
Drawaverticallineonthewallatthecenterofthe
30”widespace.TapetheRearWallTemplateonto
thewallmatchingthecenterlineandtouchingthe
bottomofthecabinet
1

31-7000110 Rev.1 9
Installation Instructions
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
12"
4"
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
NOTE:It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE::DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
30” MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
F. CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
3/8" TO EDGE
C
NOTES:
- 13” Max Cabinet Depth
- 15” deep cabinets require additional steps using
an additional installation kit: JX15BUMP
OPTION 1 OPTION 2
STEP1: Installeruses brackettomake 2marks.First
markis madebyusing thestampled slotin bracket.
Secondmark ismade onthe ousideedge ofbracket.
STEP3: Installeruses alevelto drawahorizontal line
thatconnects thetwomarks madewith thestamped
slotin thebracket.
STEP2: Installermoves brackettothe otherside of
thecabinets andmakes2 moremarks. Marksarethe
sameas STEP1,just oppositeside.
STEP4: Installeruses markstoinstall bracketin
correctposition. Thebracketis tobeinstalled per
standardrequirements(at leastone woodscrew
mountedin astud,two additionalevenly spaced
locationsfor togglebolts).Mark holelocation A,B,Cand
Dby placingthemounting bracketon thewallas shown
inthe picture.HoleC andor Dmust beina WALLSTUD.
STEP5: Setmounting bracketasideand drillholes at
allmarked locations.Ifthere isa stud,drilla 3/16”hole
forwood screws.Forholes thatdonot lineup witha
stud,drill a5/8”hole fora togglebolt.
Makeamark here,along
insidebottomof the
stampedslotprovided.
Makeamark
here,
evenwith
bottomof
stamped
slot
Makeamark here,along
insidebottomof the
stampedslotprovided
(sameasStep 1).
Makea
markhere,
evenwith
bottomof
stamped
slot
Horizontalline
A C D B
Placebracketwithin thelinescreated inprevioussteps.
Markholelocations forA,B, C,andD.
NOTE:Refer to step C “DETERMINING MOUNTING PLATE LOCATION UNDER YOUR CABINET on page 10 for aligning instructions.
C
AB
MARKING THE MOUNTING HOLES
OPTION 1: USE PAPER REAR WALL TEMPLATE
WARNING Risk ofelectric shock. Cancause injury
or death.Take care tonot drillinto electrical wiringinside
wallsor cabinets.
ThisRearWallTemplateservestolocatethemounting
holesforthebottommountingplateandtolocatethe
horizontalexhaustoutlet.
1.Usealeveltocheckthatthetemplateispositioned
accurately.
2.Locateandmarkatleastonestudontheleftorrightside
ofthecenterline.
NOTE:Itisimportanttouseatleastonewoodscrew
mountedfirmlyinastudtosupporttheweightofthe
microwave.
3.Marktheholelocationonthewallusingthetemplateat
holesAandB.MarkatleastoneholelocationinareaC
thatlinesupwiththelocationofastud.Aminimumof
threeholesmustbeusedformounting.
4.Drillholesinthemarkedlocations.Wherethereisastud,
drilla3/16”holeforwoodscrews.Forholesthatdonot
lineupwithastud,drill5/8”holesfortogglebolts.
NOTE: DONOT INSTALLTHE MOUNTING PLATE AT THIS
TIME
5.Removethetemplatefromtherearwall.
D
CAUTION Wear glovesto avoid cuttingfingers on
sharpedges.
30”

10 31-7000110 Rev.1
Installation Instructions
D
STEP2:Installerusesbrackettomake2marks.Firstmark
ismadebyusingthestampledslotinbracket.Secondmarkis
madeontheousideedgeofbracket.
STEP1:Drawaverticallineonthewallatthecenterofthe
30”space. STEP4: Installerusesaleveltodrawahorizontallinethat connectsthetwomarksmadewiththestampedslotinthe
bracket.
STEP5:Installerplacesthemountingbracketonthewallas
showninthepicture.DrawcirclesonthewallatholesAandB.
DrawatleastonecircleinareaC. AtleastonecircleMUSTline
upwithawallstud.
STEP6:Setmountingbracketasideanddrillholesatall
markedlocations.Ifthereisastud,drilla3/16”holeforwood
screws.Forholesthatdonotlineupwithastud,drilla5/8”hole
foratogglebolt.
Makeamarkhere,alonginside
bottomofthestampedslot
provided.
Makeamark
hereonthe
outsideedge
ofthebracket
Horizontalline
NOTE:RefertostepC“DETERMININGMOUNTINGPLATELOCATIONUNDERYOURCABINETonpage8foraligninginstructions.
MARKING THE MOUNTING HOLES
OPTION 2: USE METAL BRACKET AS TEMPLATE
STEP3:Installermovesbrackettotheothersideofthe
cabinetsandmakes2moremarks.Marksarethesameas
STEP2,justoppositeside.
Makeamarkhere,along
insidebottomofthe
stampedslotprovided
(sameasStep1).
Makeamark
hereonthe
outsideedgeof
thebracket
A
C
B
Placebracketwithinthelinescreatedinprevioussteps.
Markholelocationsfor
A,B,andareaC.

31-7000110 Rev.1 11
INSTALLATION TYPES (Choose A, B or C)
Thismicrowaveovenisdesigned foradaptation to
thefollowingthreetypesof ventilation:
A.Recirculating (Non-Vented Ductless)
B. Outside Top Exhaust (Vertical Duct)
C.Outside Back Exhaust (Horizontal Duct)
NOTE:Selectthetypeofventilationrequiredforyour
installationandproceed to thatsection.
BOUTSIDE TOP EXHAUST
(VERTICAL DUCT)
See page 16
Adaptorin Place
forOutside Top
Exhaust
Installation Instructions
2
OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)
See page 20
C
RECIRCULATING
·×Ø×´ßÎ×ÝÎÍÍÞÌÝÕÎÜܸ
See page 12
ACharcoalFilterAccessory Kitis requiredforthe
non-ventedexhaust.(SeeyourOwner’s Manualforthe kit
number.)
A

12 31-7000110 Rev.1
Installation Instructions
USETOPCABINETTEMPLATE
FORPREPARATIONOFTOPCABINET
A2
RECIRCULATING (Non-Vented Ductless)
CUTHOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
12"
4"
NOTE:IT IS VERY IMPORTANT TO
READAND FOLLOW THE DIRECTIONS
INTHE INSTALLATION INSTRUCTIONS
BEFOREPROCEEDING WITH THIS
REARWALL TEMPLATE.
ThisRear Wall Template serves to position the bottom
mountingplate and to locate the horizontal exhaust
outlet.
1.Use a level to check that the template is positioned
accurately.
2.Locate and mark at least one stud on the left or
right side of the centerline.
NOTE: Itis important to use at least one wood
screwmounted firmly in a stud to support the weight
ofthe microwave. Mark two additional, evenly spaced
locationsfor the supplied toggle bolts.
3.Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE:: DONOT INSTALL THE MOUNTING PLATE
ATTHIS TIME.
4.Remove the template from the rear wall.
5.Review the Installation Instruction book for your
installation situation.
Darlevuelta a lahoja para consultar la
versión en Español.
CAUTION- IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDEDDIMENSION, GREASE-LADEN AIR WILL
DISCHARGEINTO HOUSE STRUCTURE
30” MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
F. CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
Locateand mark holes to align with holes in the
mountingplate.
IMPORTANT:
LOCATEAT LEAST ONE STUD ON EITHER SIDE OF
THECENTERLINE.
MARKTHE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACEDTOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trimthe rear wall template along the dotted line.
3/8"TO EDGE
C
A
C
D
B
NOTES:
-13” Max Cabinet Depth
-15” deep cabinets require additional steps using
an additional installation kit: JX36BUMP
OPTION 1
OPTION 2
STEP1: Installerusesbrackettomake2 marks.First
markismadebyusing thestampledslotinbracket.
Secondmarkismadeon theouside edgeof bracket.
STEP2: Installermovesbrackettotheother sideof
thecabinetsandmakes2 moremarks.Marksarethe
sameasSTEP1,just oppositeside.
STEP4:
Makeamarkhere,along
insidebottomofthe
stampedslotprovided.
Makeamark
here,
evenwith
bottomof
stamped
slot
Makeamarkhere,along
insidebottomofthe
stampedslotprovided
(sameasStep1).
Makea
markhere,
evenwith
bottomof
stamped
slot
Horizontalline
A
C
D
B
INSTALLATION OVERVIEW
A1. Attach MountingPlatetoWall
A2. PrepareTopCabinet
A3. CheckBlowerOrientation
A4. AdaptingMicrowaveBlowerForRecirculation
A5.Mountthe Oven
A6. InstallingTheCharcoalFilter
•Readthe instructionson theTOPCABINET
TEMPLATE.
•Tapeitunderneaththe topcabinet.
•Drilltheholes, following theinstructions onthe TOP
CABINETTEMPLATE.
CAUTION
Wear safety goggles when drilling
holes in the cabinet bottom.
Youneed todrill holesforthetopsupport screwsand a
holelargeenoughforthepowercord to fit through.
A
Placethemounting plateagainst thewall andinsert
thetogglewings intothe holesin thewall to mount
theplate.
CAUTION Be careful to avoid pinching fingers
between the back of the mounting plate and the
wall.
Tighten allbolts.Pullthe plateawayfromthewall
to helptightenthe bolts.
3
ATTACH THE MOUNTING PLATE
TO THE WALL
A1
A
C
D
B
Attachthe plate to thewall usingtogglebolts and
woodscrews.Atleastone woodscrewmust beused
to attachtheplatetoawall stud.
Removethe toggle wingsfromthebolts.
Insert thebolts intothe mountingplatethrough
theholesdesignatedto gointodrywallandreattach
thetogglewings to3\4ėòñ÷òèäæëåòï÷
1
4
Wall
Mounting
Plate
SpacingforTogglesMore
ThanWallThickness
BoltEnd
Toggle
Bolt
ToggleWings
To use toggle bolts:
2
IMPORTANT:DoNOTremove
thecardboardspacersbetween
theheatshieldanddoor

31-7000110 Rev.1 13
Installation Instructions
AFTER: Fan Blade
Openings Facing
Forward
3
2
4
ADAPTING BLOWER
FOR RECIRCULATION
A4.
NOTE: Theexhaustadaptorwith damperis not
neededforrecirculatingmodels.Youmaywant to
savethem forpossible future use.
Carefullypull outtheblowerunit.The wires
willextend farenough toallowyouto adjustthe
blowerunit.
Rollthe blower unit90° sothat fanblade openings
arefacingtowardthe frontof theoven.
Roll
Slidetheblowerplatefromunder itsretaining
flangeandliftitoff.Removethe cover plate
installedontheback.Removeand savescrews
thatholdblowerunit tothe oven.
Removeand savescrews thathold blowerplateto
theoven.
BEFORE: Fan Blade
Openings Facing Up
1
Blower Plate
Retaining
Flange
Blower Plate
Backof
Oven
CoverPlate
Blower PlateScrews
CHECKBLOWERMOTOR
ORIENTATION
Theblowerfanbladeopening shouldbe facingthe
front ofthe microwave.Youwill havetoremovethe top
cover plate to checkthe fanblade orientation.If thefan
openingisalready facingthe frontof themicrowave,
skiptostepA5. Otherwise,continueto StepA4 to
adjustthefanmotororientation.
A3.
Blower Motor
Screws
CoverPlate

14 31-7000110 Rev.1
Installation Instructions
Placetheblowerunitback into theopening.
CAUTION Do not pull or stretch the blower
unit wiring. Make sure the wires are not pinched. 1
6
5
ADAPTING BLOWER FOR
RECIRCULATION (continued)
A4.
Replaceblowermotorscrewsremovedin Step 2.
Slidecoverplateinto positionon theback ofthe unit.
Replaceblowerplateandscrews removed inStep1.
Attachsecondcoverplate onblowerplate(including
onescrew).
CabinetFront
CabinetBottomShelf
FillerBlock
OvenTop
Equivalentto
Depthof Cabinet
Recess
2Rotatefrontofovenup
againstcabinet
bottom.
MOUNT THE OVEN
A5.
FOREASIERINSTALLATIONAND PERSONAL SAFETY,
WERECOMMENDTHAT TWO PEOPLE INSTALL THIS
OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: Ifyourcabinetis metal,use thenylon
grommetaroundthepowercordhole topreventcutting
ofthecord.
NOTE: Werecommend usingfillerblocksif the
cabinetfronthangsbelowthecabinet bottomshelf.
IMPORTANT: If filler blocks are not used,
case damage may occur from over tightening
screws.
NOTE:Whenmountingthe
oven,threadpowercord
throughhole inbottomof
top cabinet.Keepittight
throughoutSteps1–3.Do
notpinchcordorlift oven
bypulling cord. Liftoven,tiltit
forwardand hook
slotsatbackbottom
edgeontotwolower
tabsofmountingplate.
Self-Aligning Screw
Blower Plate
Backof
Oven
Blower
Plate
Screws
Blower Motor Screws
CoverPlate
CoverPlate

31-7000110 Rev.1 15
Installation Instructions
3
1
4
2
5
3
6
7
WHEN REPLACING THE
CHARCOAL FILTER
A6.
MOUNT THE OVEN (continued)
A5.
Ifthemodelisnot ventedtothe outside,the airwill be
recirculatedthroughadisposable charcoalfilterthat
helpsremovesmokeand odors.
Thecharcoalfilter shouldbereplaced whenit is
noticeably dirtyor discolored(usuallyafter6to12
months, dependingon hoodusage). SeeyourOwner’s
Manualforthe filterkitnumber.
To replace the charcoal filter:
5
4
Tighten thetwoscrewstothetopof theoven
completely.(While tightening screws,hold
theovenin placeagainst thewall andthe top
cabinet.)
Attachthe oventothe top cabinetbyinserting
2self-aligningscrewsthroughoutertopcabinet
holes. Turn twofullturnson eachscrew.Be sure
to keep power cord tight. Be careful not to pinch
the cord, especially when mounting flush to
bottom of cabinet.
Openthemicrowavedoor.
Remove2 screwsfromthetopof thegrille. (You
mayneed to openthe cabinetdoorstoremovethe
screws.
Slidethegrilletothe leftand forwardtoremove.
Slidetheoldfilterdownand outtoremoveit.
Removeplastic andother outer wrappingfromthe
newfilterand installthe newfilter.When properly
installed,thewire meshof thefilter shouldbevisible
fromthe front.
Replacethe grilleand the2 screws.
Closethedoor.
Installgreasefilters.Seethe Owner’sManual
packedwith theoven.
Insertfilter mesh-sideup
Charcoal
Filter

16 31-7000110 Rev.1
OUTSIDE TOP EXHAUST (Vertical Duct)
Insert thetogglewingsintothe holesin thewall and
place themounting plate againstthe wall.
CAUTION Be careful to avoid pinching
fingers between the back of the mounting plate and
the wall.
Tighten allbolts.Pullthe plateawayfromthewall
to helptightenthe bolts.
3
B
4
ATTACH THE MOUNTING PLATE
TO THE WALL
B1
Attach theplateto thewall usingtogglebolts and
woodscrews.Atleastone woodscrewmust beused
to attachtheplatetoawall stud..
Removethe toggle wingsfromthebolts.
Insert thebolts intothe mountingplatethrough
theholesdesignated to gointodrywalland reattach
thetogglewings to3\4ėòñ÷òèäæëåòï÷
1
CUTHOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
12"
4"
NOTE:IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
ThisRear Wall Template serves to position the bottom
mountingplate and to locate the horizontal exhaust
outlet.
1.Use a level to check that the template is positioned
accurately.
2.Locate and mark at least one stud on the left or
rightsideof the centerline.
NOTE: Itis important to use at least one wood
screwmounted firmly in a stud to support the weight
ofthe microwave. Mark two additional, evenly spaced
locationsfor the supplied toggle bolts.
3.Drill holes in the marked locations. Where there is
astud,drill a 3/16" hole for wood screws. For holes
thatdonot line up with a stud, drill 5/8" holes for
togglebolts.
NOTE:: DONOT INSTALL THE MOUNTING PLATE
ATTHIS TIME.
4.Remove the template from the rear wall.
5.Review the Installation Instruction book for your
installationsituation.
Darle vuelta a la hoja para consultar la
versión en Español.
CAUTION- IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDEDDIMENSION, GREASE-LADEN AIR WILL
DISCHARGEINTO HOUSE STRUCTURE
30” MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
F. CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
3/8"TO EDGE
C
A
C
D
B
NOTES:
- 13” Max Cabinet Depth
- 15” deep cabinets require additional steps using
anadditional installation kit: JX36BUMP
OPTION 1
OPTION 2
STEP1: Installerusesbracketto make2marks.First
markismade byusingthestampledslot inbracket.
Secondmarkismade onthe ousideedge ofbracket.
STEP2: Installermovesbracketto theothersideof
thecabinetsandmakes 2moremarks.Marks arethe
sameasSTEP1, justoppositeside.
STEP4:
Makeamarkhere,along
insidebottomofthe
stampedslotprovided.
Makeamark
here,
evenwith
bottomof
stamped
slot
Makeamarkhere,along
insidebottomofthe
stampedslotprovided
(sameasStep1).
Makea
markhere,
evenwith
bottomof
stamped
slot
Horizontalline
A
C
D
B
INSTALLATION OVERVIEW
B1. Attach MountingPlatetoWall
B2. PrepareTopCabinet
B3. CheckMotor Orientation
B4. AdaptingForOutsideVentilation
B5. AssembleandInstallAdaptor
B6. MounttheMicrowave
B7. AdjustThe ExhaustAdaptor
B8. ConnectingDuckwork
Wall
Mounting
Plate
MountingPlate
SpacingforTogglesMore
ThanWallThickness
BoltEnd
Toggle
Bolt
ToggleWings
To use toggle bolts:
2
Installation Instructions
IMPORTANT:DoNOTremovethe
cardboardspacersbetweentheheat
shieldanddoor
A
C
D
B

31-7000110 Rev.1 17
Installation Instructions
ADAPTING BLOWER FOR
OUTSIDE VENTILATION
CHECK BLOWER MOTOR
ORIENTATION
Theblowerfanbladeopening shouldbe facingthetop
ofthemicrowave.If thefanopeningis alreadyfacing
thetopof themicrowave,skip to StepB5.Otherwise,
continue to StepB4 toadjust themotororientation.
B3.
3
2
4
B4.
Carefullypull outtheblowerunit.The wires
willextend farenough toallowyouto adjustthe
blowerunit.
Rollthe blower unit90° sothat fanblade openings
arefacingtowardthe topof themicrowave.
Roll
Slidetheblowerplatefromunder itsretaining
flangeandliftitoff.Removethe cover plate
installedontheback.Removeand savescrews
thatholdblowerunit tothe oven
Removethe cover installedon theblowerplate
(includingonescrew). Removeand savescrews
holdingblowerplateto theoven.
BEFORE: Fan Blade
Openings Facing Front
1
Blower Plate
CoverPlate
Blower Motor Screws
Retaining
Flange
AFTER: Fan Blade
Openings Facing
Up
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
Youneed todrill holesforthetopsupport screws,a hole
largeenough forthe power cordtofitthrough,and a
cutout largeenough forthe exhaustadaptor.
B2
•Readthe instructionson theTOPCABINET
TEMPLATE.
•Tapeitunderneaththe topcabinet.
•Drilltheholes, following theinstructions onthe TOP
CABINETTEMPLATE.
CAUTION Wear safety goggles when drilling
holes in the cabinet bottom.
A
C
D
B
Blower Plate
Backof
Oven
Blower
Plate
Screws
Blower Motor Screw
CoverPlate
CoverPlate

18 31-7000110 Rev.1
Installation Instructions
ASSEMBLE AND INSTALL
ADAPTOR
MOUNT THE OVEN
B6.
B5.
FOREASIERINSTALLATIONAND PERSONAL SAFETY,
WERECOMMENDTHAT TWO PEOPLE INSTALL THIS
OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: Ifyourcabinetis metal,use thenylon
grommet aroundthe power cordholetoprevent
cuttingof thecord.
NOTE: Werecommend usingfillerblocksif the
cabinetfronthangsbelowthecabinet bottomshelf.
IMPORTANT: If filler blocks are not
used, case damage may occur from over
tightening screws.
Damper
Backof
Oven
CoverPlate
Placetheoven inits uprightposition, withthe top of
theunitfacingup.
×ØÝÎÖäîèöøõè÷ëèåïòúèõéäñåïäçèöäõèùìöìåïè
and are pointing up.
Insert thetabs oneach sideof thedamper into the
holesattheinsiderearofthe adaptor.
Exhaust
Adaptor
1
2
Blower Plate
NOTE: Onsome models,the exhaustadaptor and
damperassemblymayalreadybeassembled to theoven.
Placetheblowerunitback into theopening.
CAUTION Do not pull or stretch the blower
unit wiring. Make sure the wires are not pinched.
6
5
Replaceblowermotorscrewsremovedin Step 2.
Slidecoverplateinto positionon theback ofthe
unit.Replaceblower plate andscrews removed in
Step1.
Blower Plate
Backof
Oven
Blower PlateScrews
Blower Motor Screws
ADAPTING BLOWER FOR
OUTSIDE VENTILATION
(continued)
B4. Attach theexhaustadaptorto theblowerplatewith
thetwobronze metalscrewsprovided.
Make sure that the damper pivots easily before
mounting oven.
Youwill needtomakeadjustments toassureproper
alignmentwithyour houseexhaustduct afterthe
ovenisinstalled.
3
CoverPlate
NOTE: Whenmounting themicrowave, threadpower
cordthroughhole inbottom oftopcabinet. Keepit
tightthroughoutSteps1–3. Donot pinchcordor lift
microwaveoven bypulling cord.
Liftmicrowave, tiltit forward,and hookslots
atbackbottomedgeontofourlowertabs of
mountingplate.
Rotatefrontofmicrowaveovenup againstcabinet
bottom.
1
2
PowerCord

31-7000110 Rev.1 19
Installation Instructions
Attachthe oventothe top cabinetbyinserting
2self-aligningscrewsthroughoutertopcabinet
holes.Turntwofullturnson eachscrew.Be sure to
keep power cord tight. Be careful not to pinch the
cord, especially when mounting flush tobottom of
cabinet.
3
5
4
CabinetFront
CabinetBottomShelf
Tighten thetwoscrewstothetopof theoven
completely.(While tightening screws,hold theoven
inplaceagainst thewall andthe topcabinet.)
FillerBlock
OvenTop
Equivalent
to Depth
ofCabinet
Recess
Installgreasefilters.Seethe Owner’sManual
packedwith theoven.
ADJUST THE EXHAUST
ADAPTOR
B7.
Openthetop cabinetand adjusttheexhaustadaptor
to connect tothe houseduct.
CONNECTING DUCTWORK
1
2
Extend thehouse ductdowntoconnectto
theexhaustadaptor.
Sealexhaustductjoints usingduct tape.
B8.
HouseDuct
Self-Aligning Screw
ÖØÞ×ÝÝÑÎØßÎ×(continued)
B6.
Backof
Oven
Damper
CoverPlate

20 31-7000110 Rev.1
OUTSIDE BACK EXHAUST (Horizontal Duct)
PREPARING THE REAR WALL FOR
OUTSIDE BACK EXHAUST
C1
INSTALLATION OVERVIEW
C1. PrepareRearWall
C2. AttachMountingPlatetoWall
C3. PrepareTopCabinet
C4. AdjustBlower
C5. MountTheOven
Installation Instructions
C
ATTACH THE MOUNTING PLATE
TO THE WALL
C2
Attachtheplatetothewallusingtogglebolts and wood
screw. At least one woodscrew must be usedto attachthe
plate toa wall stud.
Removethetogglewings fromthe bolts.
Insert the bolts into the mounting plate through
theholesdesignatedtogointodrywalland reattachthe
toggle wings to3\4ėòñ÷òèäæëåòï÷
1
2
Youneed tocut anopening inthe rearwall foroutside
exhaust.
•Readthe instructionson theREAR WALL
TEMPLATE.
•Tapeittothe rearwall, liningup withthe holes
previouslydrilled forholes Aand Bin themounting
plate.
•Cuttheopening,followingthe instructionsof the
REARWALLTEMPLATE.
A
C
D
B
Wall
Mounting
Plate
SpacingforTogglesMore
ThanWallThickness
Toggle
Bolt
ToggleWings
To use toggle bolts:
Bolt
End
Insert the togglewings into the holes inthewallto
mounttheplateandplacethemountingplateagainst
thewall.
CAUTION Be careful to avoid pinching fingers
between the back of the mounting
plate and the wall.
Tighten all bolts.Pulltheplateawayfromthewall
to help tightenthe bolts.
3
4
CUTHOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
12"
4"
NOTE:IT IS VERY IMPORTANT TO
READAND FOLLOW THE DIRECTIONS
INTHE INSTALLATION INSTRUCTIONS
BEFOREPROCEEDING WITH THIS
REARWALL TEMPLATE.
ThisRear Wall Template serves to position the bottom
mountingplate and to locate the horizontal exhaust
outlet.
1.Use a level to check that the template is positioned
accurately.
2.Locate and mark at least one stud on the left or
right side of the centerline.
NOTE:Itis important to use at least one wood
screwmounted firmly in a stud to support the weight
ofthe microwave. Mark two additional, evenly spaced
locationsfor the supplied toggle bolts.
3.Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE::DONOTINSTALL THE MOUNTING PLATE
ATTHIS TIME.
4.Remove the template from the rear wall.
5.Review the Installation Instruction book for your
installation situation.
Darlevuelta a la hoja para consultar la
versión en Español.
CAUTION- IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDEDDIMENSION, GREASE-LADEN AIR WILL
DISCHARGEINTO HOUSE STRUCTURE
30” MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
F. CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
Locateand mark holes to align with holes in the
mountingplate.
IMPORTANT:
LOCATEAT LEAST ONE STUD ON EITHER SIDE OF
THECENTERLINE.
MARKTHE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACEDTOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trimthe rear wall template along the dotted line.
3/8"TO EDGE
C
A
C
D
B
NOTES:
-13” Max Cabinet Depth
-15” deep cabinets require additional steps using
an additional installation kit: JX36BUMP
OPTION 1
OPTION 2
STEP1: Installerusesbrackettomake2 marks.First
markismadebyusing thestampledslotinbracket.
Secondmarkismadeon theouside edgeof bracket.
STEP2: Installermovesbrackettotheother sideof
thecabinetsandmakes2 moremarks.Marksarethe
sameasSTEP1,just oppositeside.
STEP4:
Makeamarkhere,along
insidebottomofthe
stampedslotprovided.
Makeamark
here,
evenwith
bottomof
stamped
slot
Makeamarkhere,along
insidebottomofthe
stampedslotprovided
(sameasStep1).
Makea
markhere,
evenwith
bottomof
stamped
slot
Horizontalline
A
C
D
B
A
C
D
B