Haier HTW130-186S User manual

User’s Manual
Semi Automatic Washing Machine

Contents
Safety precautions
 .............................. 2
Packing list
 .......................................... 4
Machine components
 ..............................
..............................
4
Installation and adjustment

..................
5
Pre-wash preparation 7
Washing sequence
 ..............................
9
Disposal after washing
 ...................... 12
Troubleshooting
 ..................................
14
.................................. 15

Specifications
 .........................
Back cover
Please read this manual
carefully before using.
Retain it for future reference.

HTW130-186S
HTW200-186S
E-waste Guideline

2
Safety precautions
WARNING
FORBIDDEN
Meaning and description of the symbols
Contents marked with this symbol relate to product and
user safety. Please operate the machine in strict
conformity to the contents of this manual to minimize
the risk of personal injury and/or damage to the
machine.
Contents marked with this symbol describe actions
prohibited to perform. If performed these actions will
endanger the user’s personal safety and may result in
injury.
Please insert the power cord into a rated
voltage outlet. Be sure to use a
single-phase three pin outlet. Also, the
terminal of the outlet must be grounded.
If possible, please install an electric
leakage protector.
When the machine is in use, place the
power plug in a location where it can be
easily inserted and extracted by hand.
Be sure to remove the plug if power
failure occurs, when moving or cleaning
the machine, or when the machine is
idle.
If the power cord is faulty, in order to
avoid risk it must only be replaced by
our authorized after sale service
technicians. Remember to keep the pin
of the power plug clean.
Do not place the machine in a damp
place like the bathroom and never
wash it with water. Do not place wet
laundry on the
control panel.
Do not use water warmer than 50 °C . If the washing machine is installed on the
ground near carpet, make sure to keep
the ventilation hole clear of obstruction.
Ventilation hole
at the bottom of
the washing
machine

3
 

Do not attempt to take apart, repair
or alter the machine by yourself.
Do not wash laundry with volatile or
flammable materials (such as thinner,
petrol etc.).
Do not put any high temperature or
heavy objects on the washing
machine.
Keep the machine away from direct
sunlight and heat sources like the
radiator.
Disabled children or those not under
adult supervision should not operate
the machine.
To guarantee your
safety, please
ensure the power
outlet is grounded
before use.
Please check if the water
faucet is turned on and
make sure you have the
proper water pipe
connection
It is recommended to use
foamless washing powder.
To avoid abnormal vibrations in
spinning, do not use the machine to
wash water-proof laundries like
raincoats, bike covers etc.
Do not share the outlet with other electric
appliances. If the power plug is damaged,
or feels loose when plugged into the
outlet, stop using the
plug immediately.
Rated current of
fuse:10A.
Do not stretch hands into the workingmachine.It is
dangerous even if the rotation is slow. Take special
care of the children.This appliance is not intended
for use by persons (including children) with educe
physical, sensoryor mental capabilities ,
of lack of
experience andknowledge,
unless they have been
given supervision or instruction
conceming use of the
appliance by a person
responsible for their safety.
To protect your laundry and
the washing machine,please
removr all coins,buttons,sand,
hairpinsand other foreign
materials before washing.


Machine Components
Wash timer Drain selector
Wash selector Spin timer
Control
panel
If you wish to set it
for less than 3
min, you should
first turn past 9
min and then turn
back.
Intensity can be
set to standard
or
Warning: do not
set the switch on
Drain position
during washing.
If to set to less than
1 min, in order to
ensure a long
service life, please
first turn past 2 min
and then turn back.
Packing list
Water intake
hose Gland Draining
hose (5EA)
Bottom foot
Spin tub inner cover
Spin timer
Spin tub
Overflow filter
Wash tub
Lint filter
Pulsator
Base frame
Water-filling entrance
Water-filling transfer
Control panel
Draining hose
Major frame
Wash timer
Wash selector
Spin tub outer cover
Drain selector
Wash tub cover
4
S
T
A
N
D
A
R
D
STRONG
(HTW130-186S only)
strong.
Semi automatic
washing machine

5
Drain hose drainage should be smooth and unobstructed.
Installation and adjustment
overflow filter
lint filter
For your security and to ensure correct operation of the machine, please install and
adjust the machine according to this manual’s instructions.
Installation of the lint filter
Place the bottom side of the lint filter into the
overflow filter, then push the top side into the
overflow filter.
After installation, please double check to
make sure that the lint filter is installed in the
correct location; otherwise it may fall off
during operation.
Drain hose usage
1.The height of the drain hose shall be
less than 10cm, or the drainage will
not be smooth enough and cause
incomplete drainage.
2.Do not tramp or press the drain hose.
3.If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
4.If extra drain hose is needed, please make
separate purchase. The inner diameter of the
extra hose shall not less than 30mm,and the
length shall not exceed 1.5m.
If the extra hose is too long, cut it either
at point A or B.

6
Install the water intake hose
Insert the water intake hose
into the water-inlet entrance
on the control panel.
Water intake hose
Water inlet
Change the direction of the drain hoses
Add water as necessary.
2.Install the drain hose
Drain valve parts
The drain hoses in the wash tub when out off factory ,before use the machine,
please screw the drain hose on the drain valve parts , make sure the drain hose
fixing as necessary.
1.Remove the cover
Install the bottom foot (HTW130-186S only)
1. Tilt the washing machine slightly from the front of the machine, and install
the Bottom feet with the three mounting pores on the front of the base.
Make sure that the foot buckles be installed in place. (Figure 1)
2. Tilt the washing machine slightly from the back of the machine, and install
the Bottom feet with the two mounting pores on the back of the base.
Make sure that the foot buckles be installed in place. (Figure 2)
Bottom foot Bottom foot
Figure 1 Figure 2

7
Pay attention to followings before washing the laundries
Basic know-how
Pre-wash Preparation




The maximum capacity during washing and spinning cycles
refers tothe max weight of standard dry laundry that can be
washed or spun at one time. The laundry quantity during one
washing cycle should be lower than the rated capacity.
Thickness, size, and the type of cloth will influence actual
washing capacity. It is acceptable to put in a reasonable amount
of laundry as the laundry will be mixed around during the
washing process.
To avoid splashing, do not select the “Maximum” water level for
low loads.
Using high sudsing detergent is not recommended.
Check tosee if
the items have
special washing
requirements.
Put hard to
absorb water
items into the
machine by hand.
Empty out
pockets. Take
out any coins,
sand, hairpins
Check tosee if
the items are
appropriate for
use with the
washing
Do not overload the washer.
Stretch and loosen the laundry
before putting it into the washer.
Tie any long strips;
fasten buttons; and
close any zippers.
For laundry that
is susceptible to
lint balls and/or
has long fur,
turn it inside out
before putting it
in the washer.
Do not put
laundry
polluted by
chemicals into
the washing
machine
directly.
For heavily soiled laundry, try to
remove dirt such as mud or dust
first and apply detergent in
advance. This will help to
remove the stains more easily.
Divide
non-colorfast
laundry from
other laundry.
When the pulsator is running, some noise may emit from
laundry that contains buttons. To minimize this noise,
surround laundry with buttons with other laundry.

8
Detergent use
Using bleach detergent:
How to add detergent:









Method 1 - directly dissolving in the machine:
1.Add a small quantity of water to the machine.
2.Add the detergent powder. Run washing machine for 30 seconds to dissolve powder
completely.
3.Place laundry into the washing machine and select a suitable water level.
Method 2 - instantly dissolving the detergent powder:
1.Prepare warm water at 30 °C and a container.
2.Add the detergent powder whilestirring until it dissolves fully.
Laundry powder is more prone to damage laundry than liquid detergent. Please exercise
caution and do not exceed the maximum quantity.
Dosages of detergent powder may vary. Please follow the instructions on the detergent
Add water to suitable levels. Dilute the bleach with a separate container. Pour it slowly
into the washing machine.
Avoid using whitening agents on laundry with colors and/or patterns as they are prone to
lose color.
The whitening agent should not come in direct contact with the laundry.
Refer to the product instructions for information on proper usage and quantity
Dissolve powder whitening agents before use.

9
Washing sequence
Washing
1.Inlet selector
4 Select intensity..
2.Add water
Set the selector to “WASH”.(Figure1)
Machine begins to dispense detergent uniformly.(Figure2)
3.Put in the wash load. Add more water as
necessary.(Figure3)
Select or water flow
intensity according to the wash load.(Figure4)
5.Select wash timer.
Select wash time according to the wash load.
(Figure5)
6.After the wash is completed, set the
switch to the “DRAIN” position.(Figure6 )
Figure 1
4
2
TOR
3
6
5
S
T
A
N
D
A
R
D
STRONG
“STRONG”
“STANDARD”
Figure
Figure
Figure
Figure
Figure

10
Push Push
Proper Proper
Outer cover of
The spin tub
Inner cover of
The spin tub
The laundry
is slanted.
Gland
No gland
1. Put the laundries into the spin tub evenly and smoothly.
2.Spin
(2)Close both the inner and outer covers of the spin tub.
(3) Spin for 1-2 minutes.
(1) Distribute the laundry into the spin tub smoothly and evenly.
Note: the gland must be inserted properly even if the laundry quantity is small.
3.Run the foam-removing spinning.
(1) Open the outer cover of the spin tub.
(2) Set the water-filling selector control
rod at the "SPIN" side. Fill water for
about 1 minute.
If the water quantity filled is too large,
the water may flow out from the wash
tub side. Please twist the water tap to
limit the water filling.
(3) Close the outer cover of the spin tub.
Spin for 1-2 minutes.
Mid-wash spin cycle
TOR