Haiku L3127-X5 User manual

INSTALLATION GUIDE
INSTALLATION GUIDE

READ AND SAVE THESE INSTRUCTIONS
Technical Specifications
Check the fan label to make sure it is the correct voltage.
Operating voltage Diameter Weight Operating frequency
120 VAC, 1 Φ 52 in. (132 cm) 11 lb (5 kg) 60 Hz
220/240 VAC, 1 Φ 52 in. (132 cm) 11 lb (5 kg) 50/60 Hz
Tools Needed
• Ladder
• Wire Strippers
• Phillips Screwdriver
• Hex Key
• Wrenches
Scan for online Haiku Home app help Models: L3127-X5, L3127-X6, FR127C-U1EXX

1
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Mounting Bracket
Control Box
Wiring Cover
LED Diuser Ring
Mounting Ball & Hardware
Lower Cover Trim
Lower Cover Ring
Extension Tube
Motor Unit
(3) Airfoils
Remote Control
Hardware Pack
Haiku Wi-Fi Module†
PARTS
See the following page for hardware.
Provided if purchased as an accessory or
with the Haiku Wall Control
†
a
b
c
d
e
f
g
h
i
j
k
l
m
a
b
c
d
e
f
g
h
i
j
k
l
m

2REV.E 11/20/17 ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
HARDWARE
Hardware and tools needed for installation are packaged in the hardware pack. Hardware below shown at
actual size.
Mounting Hardware
M8 Bolt M8 Washer M8 Nylock Nut
Airfoil Hardware
(6) M5 Screws with Tooth Washer
Wiring Cover Hardware
(4) M4 Socket Head Cap Screws
Lower Cover Hardware
Mounting Ball & Hardware
Steel Pin
Wedge 4 mm Self-Tapping
Screw
Mounting Ball
(2) Painted M3.5 Screws
or
BlackWhite

3
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
1PREPARE THE FAN SITE
Installation requires basic electrical knowledge. Contact a licensed electrician if you are uncomfortable
performing electrical work!
2
1Disconnect Power!
Disconnect power to the fan location before wiring fan!
If required by your local electrical code, a licensed electrician
must install the fan.
A means for disconnection must be incorporated in the
fixed wiring in accordance with the wiring rules.
If you are installing your fan to an outlet box, it must be suitable for
fan support. If there is not an outlet box at the fan location, install
one on a ceiling joist or beam.

4REV.E 11/20/17 ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
INSTALL THE MOUNTING BRACKET
2
b
a
c
Installation may vary. Refer to
the outlet box instructions.

slope
open side
slope
5
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Secure the mounting bracket (a) to the outlet box (b) with the screws supplied with the outlet box (c).
Outlet Box Hardware:
c. Screw (supplied with outlet box)
STEP COMPLETED
Sloped Ceilings
If mounting to a sloped ceiling, install the mounting bracket
so that the open side faces upward with the slope.

6REV.E 11/20/17 ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
PREPARE THE AIRFOILS
3
1 2
a b
SELECT LENS
(BLACK FANS WITH LIGHTS) MATCH AIRFOIL STICKERS

7
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
2
1Black fans with lights: For softer lighting, remove the white lens and install the smoky lens before
attaching the airfoils.
a. Twist to uninstall white lens.
b. Twist smoky lens to lock in place.
Make sure the stickers on the airfoils match the stickers on the fan hub.

8REV.E 11/20/17 ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
INSTALL THE AIRFOILS
4
b
c
a
1 2
d
INSTALL AIRFOILS FANS WITHOUT LIGHTS

9
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Rest the motor assembly (a) on your lap. Moving clockwise, install each airfoil (b) with the provided
hardware. Tighten the screws to 2.5 N·m (22.1 in·lb). Do not use power tools to install the airfoils, and
do not over-tighten the screws! Over-tightening the screws may cause the airfoils to warp and void
your warranty.
Airfoil Hardware:
c. (6) M5 screws with tooth washer
Fans without lights: Position the motor cover (d) over the motor, and then place both hands flat on the
cover and turn it clockwise to lock it in place.
DO NOT USE POWER TOOLS!
STEP COMPLETED
2
1

tooltip
10 REV.E 11/20/17 ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
INSTALL THE LOWER EARTH/GROUND WIRE
5
a
c
b
d
SECURE EARTH/GROUND WIRE
POSITION EXTENSION TUBE
1 2

Box cables back, in color
11
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
STEP COMPLETED
2
1Lower the extension tube (a) onto the motor shaft. Ensure the yellow arrow sticker on the extension
tube is aligned with the sticker on the motor.
Remove the screw and ground tag from the motor shaft. Secure the Earth/Ground wire to the motor
shaft with the captive screw (b). Connect the yellow Earth/Ground female spade connector (c) to the
male connector (d) on the motor.
Safety Cable Installation
You may be required to secure the fan directly to the building
structure if your local safety code requires it. Check your
local code! Refer to the Safety Cable instructional sheet
included with this guide for more information.
Acceptable building structures include a wooden beam or a
metal mounting brace secured between two beams. In some
cases it may be necessary to install additional structural
material to provide attachment points.

12 REV.E 11/20/17 ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
6CONNECT MOTOR WIRING AND SECURE EXTENSION TUBE
1 32
d
SECURE HARDWARE REMOVE SLACK
INSTALL WIRING HARNESSES
a
a
b
c
e

13
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Remove the tie holding the wiring harnesses to the extension tube. Plug the two large wiring harnesses
(a) into the receptacles on the motor. Plug the small, male wiring harness (b) into the female wiring
harness from the motor shaft.
Align the bolt holes on the extension tube with the holes on the motor shaft, and then secure the tube
with the provided hardware and wrenches.
Mounting Hardware:
c. M8 bolt
d. M8 washer
e. M8 nylock nut
To remove slack, gently tug on the cables at the top
of the extension tube.
STEP COMPLETED
2
1
3

14 REV.E 11/20/17 ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
SECURE THE LOWER COVER
c
7
b
a

STEP COMPLETED
15
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Place the lower cover ring (a) around the extension tube, resting it evenly on the motor. There should
be a very small gap between the cover and the airfoils. Rotate the cover ring clockwise until it stops.
Thread the wires through the opening in the lower cover trim (b), and then slide the trim down the
extension tube, resting it evenly on the cover ring.
Align the screw holes on the trim with the motor screw holes, and then secure the trim in place with
the provided screws (c).
Lower Cover Hardware:
c. (2) Painted M3.5 screws
2
1
3
or
BlackWhite

16 REV.E 11/20/17 ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
ARRANGE LED DIFFUSER RING, WIRING COVER, AND MOUNTING BALL
8
a
b
c
Do not seat the LED diuser ring in the wiring cover at this step!

17
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Slide the LED diuser ring (a), wiring cover (b), and mounting ball (c) down the extension tube (in that order),
resting them on the fan hub.
STEP COMPLETED
Do not seat the LED diuser ring in the wiring cover at this step!

18 REV.E 11/20/17 ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
ATTACH THE MOUNTING BALL
c
ab
Inner
slot
SEAT MOUNTING BALL
21
INSTALL WEDGE
9