Haiku L3127-X6 User manual

INSTALLATION GUIDE
INSTALLATION GUIDE

READ AND SAVE THESE INSTRUCTIONS
Technical Specifications
Check the fan label to make sure it is the correct voltage.
Operating voltage Diameter Weight Operating frequency
120 VAC, 1 Φ 132 cm 5 kg 60 Hz
220/240 VAC, 1 Φ 132 cm 5 kg 50/60 Hz
Tools Needed
• Ladder
• Wire Strippers
• Phillips Screwdriver
• Hex Key
• Wrenches
Models: L3127-X5, L3127-X6, FR127C-U1EXX
Scan or visit resources.haikuhome.com/help
for online Haiku mobile app help

1
HAIKU® BY BIG ASS FANS
Mounting Bracket
Control Box
Wiring Cover
LED Diuser Ring
Mounting Ball and Hardware
Lower Cover Trim
Lower Cover Ring
Extension Tube
Motor Unit
(3) Airfoils
Remote Control
Hardware Pack
PARTS
a
b
c
d
e
f
g
h
i
j
k
l
a
b
c
d
e
f
g
h
i
j
k
l

2REV. F 06/08/2018 |© 2015 BIG ASS FANS |ALL RIGHTS RESERVED
HARDWARE
Hardware and tools needed for installation are packaged in the hardware pack. Hardware below shown
at actual size.
Mounting Hardware
M8 Bolt M8 Washer M8 Nylock Nut
Airfoil Hardware
(6) M5 Screws with Tooth Washer
Lower Cover Hardware
Mounting Ball and Hardware
Steel Pin
Wedge 4 mm Self-Tapping
Screw
Mounting Ball
(2) Painted M3.5 Screws
or
BlackWhite
Wiring Cover Hardware
(4) M4 Socket Head Cap Screws

3
HAIKU® BY BIG ASS FANS
1PREPARE THE FAN SITE
Installation requires basic electrical knowledge. Contact a licensed electrician if you are
uncomfortable performing electrical work or if legally required in your area.
2
1Disconnect Power!
Disconnect power to the fan location before wiring fan!
If required by your local electrical code, a licensed
electrician must install the fan.
The ground wire must be connected to the supply ground
and its length must be longer than the safety cable!
A readily accessible disconnect device shall be
incorporated external to the equipment.
A means for disconnection must be incorporated in the
fixed wiring in accordance with the wiring rules.
If you are installing the fan directly to the building structure or to
a ceiling-mounted outlet box, the structure or outlet box must be
suitable for fan support.

slope
open side
slope
4REV. F 06/08/2018 |© 2015 BIG ASS FANS |ALL RIGHTS RESERVED
Outlet Box
If your local electrical code requires the fan to be installed on a ceiling-mounted outlet box, the outlet box
must be suitable for fan support. If there is not an outlet box at the fan location, one should be installed on
a ceiling joist or beam and properly wired.
Concrete Ceiling
If installing your fan on a concrete ceiling, ensure
power wiring has been routed to the fan site. Attach
the mounting bracket directly to the ceiling using four
Ø 6 mm anchor bolts (not supplied). If required by
your local building and safety code, install an Ø 8 mm
anchor hook (not supplied) for the safety cable.
Wood Ceiling Joist
If installing your fan on a wood ceiling joist, ensure
power wiring has been routed to the fan site. Attach
the mounting bracket directly to the joist using two
wood screws (not supplied). Haiku Home recommends
using corrosion-resistant 12-11 x 45 mm hex head
timber screws with seal.
INSTALL THE MOUNTING BRACKET
2
Sloped Ceilings
If mounting to a sloped ceiling, install the mounting
bracket so that the open side faces upward with the
slope.

5
HAIKU® BY BIG ASS FANS
2a Outlet Box
Page 6
2c Wood Ceiling Joist
Page 10
2b Concrete Ceiling
Page 8

6REV. F 06/08/2018 |© 2015 BIG ASS FANS |ALL RIGHTS RESERVED
INSTALL THE MOUNTING BRACKET (OUTLET BOX)
2a
b
a
cInstallation may vary. Refer to the outlet box instructions.

7
HAIKU® BY BIG ASS FANS
STEP COMPLETED
Secure the mounting bracket (a) to the outlet box (b) with the screws supplied with the outlet box (c).
Outlet Box Hardware:
c. Screw (supplied with outlet box)

≥ 50 mm
b b b b
8REV. F 06/08/2018 |© 2015 BIG ASS FANS |ALL RIGHTS RESERVED
INSTALL THE MOUNTING BRACKET (CONCRETE CEILING)
2b
c
≥ 65 mm
aØ11–12 mm
Use the mounting bracket as a template to
mark drill locations for the four mounting holes.
Install an anchor hook for
the safety cable if required
by your local building and
safety code.