Haiku L3127-X5 User manual

INSTALLATION GUIDE
INSTALLATION GUIDE

CONTACT US
By selecting a Haiku®fan, you’ve chosen quality design, heightened comfort and eortless conservation. Use
this guide to safely install your fan. See your Owner's Manual to discover everything your fan can do. Please
contact us with any questions you may have by calling 1-855-MY-HAIKU, or visit us at www.haikuhome.com
to learn more about Haiku.
Visit www.haikuhome.com/service to watch videos of the installation process.
United States
2348 Innovation Drive
Lexington, KY 40511
855 694 2458
Canada
6300 Northwest Dr, Unit 3
Mississauga, ON L4V 1J7, Canada
1 844 924 4277

Installation Guide
For maintenance and troubleshooting
procedures, see your Owner's Manual.
Topic Page
Technical Specifications 2
Tools Needed 2
Parts 3
Hardware 4
Prepare the Fan Site 5
Install Your Fan 6
READ AND SAVE THESE INSTRUCTIONS

2REV.A ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
Disconnect power to the fan location before installing the fan! Do not use the fan with a dimmer
switch!
If required by your local electrical code, a licensed electrician must install the fan.
Technical Specifications
Check the fan label to make sure it is the correct voltage.
Model Operating voltage Diameter Weight Operating frequency
L3127-X5 120 VAC, 1 Φ 52 in. (132 cm) 11 lb (5 kg) 60 Hz
L3127-X6 220/240 VAC, 1 Φ 52 in. (132 cm) 11 lb (5 kg) 50/60 Hz
Tools Needed
• Ladder
• Wire Strippers
• Phillips Screwdriver (provided)
• Hex Key (provided)
• Wrenches (provided)
Box Contents
As you remove the fan from its packaging, make sure you are not missing any components required for
assembly and operation. If you ordered multiple fans, be sure to keep the components of each fan together!
!
!

3
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Mounting Bracket
Control Box
Wiring Cover
LED Diuser Ring
Mounting Ball & Hardware†
Lower Cover Trim
Lower Cover Ring
Extension Tube††
Motor Unit
(3) Airfoils
Remote Control
Hardware Pack
Wiring Harness†††
PARTS
See the following page for hardware.
See Hardware page
Two lengths provided
Packaged with control box
†
††
†††
a
b
c
d
e
f
g
h
i
j
k
l
m
a
b
c
d
e
f
g
h
i
j
k
l
m

4REV.A ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
HARDWARE
Hardware and tools needed for installation are packaged in the hardware pack. Hardware below shown at
actual size.
Mounting Hardware
M8 Bolt M8 Washer M8 Nylock Nut
Airfoil Hardware
(6) M5 Screws with Tooth Washer
Wiring Cover Hardware
(4) M4 Socket Head Cap Screws
Lower Cover Hardware
Mounting Ball & Hardware
Steel Pin
Wedge 4 mm Self-Tapping
Screw
Mounting Ball
(2) Painted M3.5 Screws
or
BlackWhite

5
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
1PREPARE THE FAN SITE
Installation requires basic electrical knowledge. Contact a licensed electrician if you are uncomfortable
performing electrical work!
3
2
1Disconnect Power!
If you are installing your fan to
an outlet box, it must be suitable
for fan support.
If there is not an outlet box at
the fan location, install one on a
ceiling joist or beam.
For softer lighting, remove the white
lens and install the smoky lens before
attaching the airfoils.
1. Twist to uninstall white lens.
2. Twist smoky lens to lock in place.
Disconnect power to the fan
location before wiring fan!
Outlet Box Black Fans Only

6REV.A ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
2CONNECT THE WIRING HARNESS
a
AC HOT/L1
AC NEUTRAL/L2
GREEN
WHITE
BLACK
PE/EARTH GROUND
Do not connect the green (Earth/Ground)
wire on the wiring harness at this step!

7
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Make sure power is disconnected before wiring the fan!
Do not connect the fan to a damaged power source! Do not attempt to resolve electrical failures on
your own. Consult a qualified electrician if uncertain of the electrical installation of this fan.
Make the electrical connections by securing the supply power wires to the loose ends of the wiring
harness (a) with the provided wire nuts.
Test the connection by lightly tugging on the wires. Do not connect the green (Earth/Ground) wire on
the harness at this step!
Tuck the power wiring and wire nuts into the outlet box so that only the harness and the supply Earth/
Ground wire hang through.
AC Hot/L1
Black
AC Neutral/L2
White
PE/Earth Ground
Green
North America
100–120 V system Black White Green or Bare Copper
All other regions Brown Blue Green with Yellow Tracer
!
!
3
2
1

8REV.A ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
INSTALL THE MOUNTING BRACKET
3
b
a
c
Installation may vary. Refer to
the outlet box instructions.
1 2
CONNECT EARTH/GROUND WIRES
ATTACH MOUNTING BRACKET
dd
e
f

slope
open side
slope
9
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Make sure power is disconnected before installing the mounting bracket!
Secure the mounting bracket (a) to the outlet box (b) with the screws supplied with the outlet box (c).
Outlet Box Hardware:
c. Screw (supplied with outlet box)
Use a wire nut to secure the supply ground wire (d) to the ground wires from the wiring harness (e)
and the mounting bracket (f). Tuck the wiring and wire nuts into the junction box so that only the wiring
harness hangs through.
!
STEP COMPLETED
Sloped Ceilings
If mounting to a sloped ceiling, install the mounting bracket
so that the open side faces upward with the slope.
2
1

10 REV.A ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
INSTALL THE AIRFOILS
4
b
c
a
Make sure the colored stickers on the airfoils
match the colors of the stickers on the fan hub!

11
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Rest the motor assembly (a) on your lap. Moving clockwise, install each airfoil (b) with the provided hardware.
Securely tighten the screws.
Airfoil Hardware:
c. (6) M5 screws with tooth washer
STEP COMPLETED

12 REV.A ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
INSTALL THE LOWER EARTH/GROUND WIRE
5
a
c
1 2
b
d
SECURE EARTH/GROUND WIRE
POSITION EXTENSION TUBE

13
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
STEP COMPLETED
2
1Lower the extension tube (a) onto the motor shaft. Ensure the yellow arrow sticker on the extension
tube is aligned with the sticker on the motor.
Remove the screw and ground tag from the motor shaft. Secure the Earth/Ground wire to the motor
shaft with the captive screw (b). Connect the yellow Earth/Ground female spade connector (c) to the
male connector (d) on the motor.
Safety Cable Installation
You may be required to secure the fan directly to the building
structure if your local safety code requires it. Check your
local code! Refer to the Safety Cable instructional sheet
included with this guide for more information.
Acceptable building structures include a wooden beam or a
metal mounting brace secured between two beams. In some
cases it may be necessary to install additional structural
material to provide attachment points.

14 REV.A ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
6CONNECT MOTOR WIRING AND SECURE EXTENSION TUBE
1 32
d
SECURE HARDWARE REMOVE SLACK
INSTALL WIRING HARNESSES
a
a
b
c
e

15
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Remove the tie holding the wiring harnesses to the extension tube. Plug the two large wiring harnesses
(a) into the receptacles on the motor. Plug the small, male wiring harness (b) into the female wiring
harness from the motor shaft.
Align the bolt holes on the extension tube with the holes on the motor shaft, and then secure the tube
with the provided hardware and wrenches.
Mounting Hardware:
c. M8 bolt
d. M8 washer
e. M8 nylock nut
To remove slack, gently tug on the cables at the top
of the extension tube.
STEP COMPLETED
2
1
3

16 REV.A ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
SECURE THE LOWER COVER
c
7
b
a

STEP COMPLETED
17
HAIKU® HOME ●WWW.HAIKUHOME.COM/SERVICE ●1-855-MY-HAIKU
Place the lower cover ring (a) around the extension tube, resting it evenly on the motor. There should
be a very small gap between the cover and the airfoils. Rotate the cover ring clockwise until it stops.
Thread the wires through the opening in the lower cover trim (b), and then slide the trim down the
extension tube, resting it evenly on the cover ring.
Align the screw holes on the trim with the motor screw holes, and then secure the trim in place with
the provided screws (c).
Lower Cover Hardware:
c. (2) Painted M3.5 screws
2
1
3
or
BlackWhite

18 REV.A ●© 2015 HAIKU HOME. ALL RIGHTS RESERVED.
ARRANGE LED DIFFUSER RING, WIRING COVER, AND MOUNTING BALL
8
a
b
c
Do not seat the LED diuser ring in the wiring cover at this step!