Hama 00176547 User manual

GB
Operating instruction
WiFi Devices
WiFi-Geräte
00176547
00176548
00176549
00176550
00176551
00176552
00176553
00176554
00176555
00176556
00176558
00176559
00176565
00176566
00176567
00176568
00176570
00176571
00176573
00176574
00176575
00176576
00176577
00176578
00176579
00176581
00176582
00176583
00176584
00176585
00176586
00176587
00176588
00176589
00176590

2
1. Read first ..............................3
1.1 Explanation of Warning Symbols and Notes3
1.2 Safety Notes .........................3
2. Introduction............................3
3. System Requirements ....................3
3.1 Preparation ..........................4
Loading the Hama Smart Solution app .......4
3.2 Dual-band routers (2.4 GHz / 5 GHz). . . . . . .4
4. Mounting and getting Started .............5
4.1 WiFi LED bulbs .......................5
4.1.1 Product features......................5
4.1.2 Integrating lamps in the Hama Smart Solution
app ....................................5
4.2 WiFi wallswitch.......................7
4.2.1 Product features......................7
4.2.2 Mounting ...........................7
4.2.3 Integrating devices in the Hama Smart Solution
app ....................................7
4.3 WiFi Power Socket/Power Strip ..........8
4.3.1 Product features......................8
4.3.2 Integrating devices in the Hama Smart Solution
app ....................................8
4.4 WiFi Door / Window Contact ............9
4.4.1 Product features......................9
4.4.2 Mounting ...........................9
4.4.3 Integrating devices in the Hama Smart Solution
app ...................................10
4.5 WiFi Motion Detector .................11
4.5.1 Product features.....................11
4.5.2 Mounting
......................................12
4.5.3 Integrating devices in the Hama Smart Solution
app ...................................13
4.6 WiFi camera ........................13
4.6.1 Product features.....................13
4.6.2 Installation.........................14
4.6.3 Integrating devices into the Hama Smart
Solution app ............................14
4.7 WiFi controller for LED strips ...........15
4.7.1 Product features.....................15
4.7.2 Installation.........................15
4.7.3 Integrating devices into the Hama Smart
Solution app ............................15
5. Timer, automation and 1-click control ......16
5.1. Timer*.............................16
5.2 1-click control and automation .........16
6. Integration in Amazon Alexa .............17
7. Integration in Google Home ..............17
8. FAQs and support ......................18
10. Care and Maintenance .................23
11. Warranty Disclaimer ...................23
13. Declaration of Conformity...............23

3
GOperating instruction
1. Read first
Thank you for choosing a Hama product.
Take your time and read the following instructions and
information completely. Please keep these instructions in a
safe place for future reference. If you sell the device, please
pass these operating instructions on to the new owner.
1.1 Explanation of Warning Symbols and Notes
Risk of electric shock
This symbol indicates product parts energized with a
dangerous voltage of sufficient magnitude to constitute a
risk of electric shock.
Warning
This symbol is used to indicate safety instructions or to
draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or
important notes.
1.2 Safety Notes
•This product is intended for private, non-commercial use
only.
•Use the product for its intended purpose only.
•Protect the product from dirt, moisture and overheating,
and only use it in a dry environment.
•Do not drop the product and do not expose it to any
major shocks.
•Do not operate the product outside the power limits
given in the specifications.
•Do not use the product in the immediate vicinity of
heaters or other heat sources or in direct sunlight.
•Do not open the device or continue to operate it if it
becomes damaged.
•Do not attempt to service or repair the product yourself.
Leave any and all service work to qualified experts.
•Use the item only in moderate climatic conditions.
•Do not use the product in moist environments and avoid
splashes.
•Buy special or suitable installation material from a
specialised dealer for wall-mounting.
•After the product has been mounted, check that it
is sufficiently secure. You should repeat this check at
regular intervals.
•Before mounting, check that the wall you have chosen
is suitable for the weight to be mounted. Also make
sure that there are no electric, water, gas or other lines
running through the wall at the mounting site.
•Do not modify the product in any way. Doing so voids
the warranty Children are not permitted to play with the
device. Children may not clean the product or perform
user maintenance without supervision.
•Keep this product, as all electrical products, out of the
reach of children!
•Dispose of packaging material immediately according to
locally applicable regulations.
•The product is intended for indoor use only.
•The product may only be operated with the type of power
supply network described on the name plate.
•Benutzen Sie das Produkt nicht in Bereichen, in denen
elektronische Produkte nicht erlaubt sind.
2. Introduction
Control your smart devices very easily using an app, a
switch or your voice. Our smart products can be easily
connected to your wireless home network via WiFi. No
additional gateway is required; they work with every
WLAN router. They can be controlled using a mobile device
(mobile phone/tablet) and using the Amazon Alexa/Echo
and Google Home voice services (not 00176553).
3. System Requirements
Note - Alexa*
To use the product with Amazon Alexa, you need a de-
vice that supports Amazon Alexa (for example, Amazon
Echo/Echo Dot, etc.). The device must be integrated in
your home network and connected to the Internet.
Note - Google*
To use the product with Google, the Google Assistant
must be integrated in your home network and connected
to the Internet.
Note - IFTTT
The service for the support of the IFTTT software through
the products listed here has been discontinued. However,
it is possible that printed operating instructions or pack-
aging still refer to this discontinued service.
Note
The following requirements must be fulfilled for success-
ful startup and operation:
•A functioning wireless home network (WiFi/WLAN)
that is turned on
•Please note that only 2.4 GHz WiFi is currently
supported for the network integration. Check whether
your network is a 2.4 GHz network.
•A mobile device (smartphone, tablet, etc.) that is WiFi/
WLAN-enabled and connected to your home network
•The Hama Smart Solution App, installed on your
mobile device
*Does NOT affect the motion detector 00176554

4
3.1 Preparation
Loading the Hama Smart Solution app
•Download the Hama Smart Solution app from the
Apple App Store or the Google Play Store using your
mobile device.
•Open the Hama Smart Solution app.
•If you’re using it for the first time, you’ll have to register
and create a new account. If you already have an
account, log in using your login details.
•Click Create family.
•Enter a family name. After that, you can deactivate
rooms that are not being used by clicking the ticks. You
can add or remove rooms at any time; to do so, simply
click the cog wheel at the top right.
•Click Finish.
Note - Family location
To complete a family, it is not necessary to define the
family location manually. Based on the IP address and
the time zone set on the smartphone, the app also works
without further information. Should you need more
precise location determination at a later time, you can
add the details previously omitted (under Profile/Family
Management).
3.2 Dual-band routers (2.4 GHz / 5 GHz)
Many of the current routers transmit on two different
frequency bands (sometimes even in parallel): 2.4 GHz and
5 GHz. The advantages of the 2.4 GHz frequency are the
longer range and compatibility with older terminal devices
that do not support 5 GHz. Please note that our smart
products currently only support 2.4 GHz. If you use a dual-
band router and this results in connection problems, there
are three possible ways to resolve them:
•Deactivate 5 GHz frequency
You will find a control for both frequency bands in the
router settings (WLAN item), depending on model.
Select the 2.4 GHz frequency (or deactivate the 5 GHz
frequency) there. If necessary, consult the operating
instructions of your router.
•Change the name of the wireless local area
network (SSID)
You will find a control for both frequency bands in the
router settings (WLAN item), depending on model. There
you can change the names (SSID) of the frequencies –
for example, by simply including the frequency (such as
‘2.4’, for example) in the name. This will allow you to
specifically select the 2.4 GHz frequency. If necessary,
consult the operating instructions of your router.
•Add compatibility mode (Access Point mode)
If you have no means of ensuring that your smartphone
is on a 2.4 GHz network, you can add your smart product
using the compatibility mode (Access Point mode).
To do so, open the Hama Smart Solution app and click + at
the top right. Next select the device you want to integrate,
and, in the upper-right area, select ‘Otherwise’. Then select
‘AP Mode’ and confirm the following instructions. Enter
your WLAN password (Pic 2) and confirm with OK.

5
Pic 1 Pic 2
Brief instructions will now appear.
Click Connect now (Pic 3), and, in the WLAN network
overview (Pic 4), select the network with the name
SmartLife_XXXX.
Pic 3 Pic 4
Then click your smartphone’s Back button to return to the
app. Your lamp will now be connected.
4. Mounting and getting Started
4.1 WiFi LED bulbs
4.1.1 Product features
Safety Notes
Warning
•Use this product only with lights and fittings that are
approved for the application and appropriate for the
product. Please check that the product is in perfect
working order before making use of it.
•Whenever changing the light, always ensure that the
light or fitting in question is current-free. Switch it off
and/or pull the mains plug.
•Please note that lights (even LEDs) can generate heat
and may become hot. Always let the light cool off for a
few minutes before touching it or changing it.
Risk of electric shock
Using damaged or inappropriate lights or fittings carries
the risk of electric shocks.
This WiFi LED lamp is used for indoor home lighting, effect
lighting, or for creating personalised lighting atmospheres.
Depending on the model, you can select from 16 million
different colours or different colour temperatures (for
example, daylight for your workspace). Further possible
settings are: Switch on/off and smooth dimming.
The following selection of voice commands is also available:
•Turn on/off
‘Alexa/OK Google, turn on/off the light.’
•Dim to X%
‘Alexa/OK Google, decrease the light to X%.’
•Dim by X%
‘Alexa/OK Google, decrease the llight to X%.’
•Selection of colour temperature or colour
‘Alexa/OK Google, turn the light warm white.’ (red, white,
etc.)
4.1.2 Integrating lamps in the Hama Smart Solution
app
•Twist the smart lamp into a suitable fixture.
•The smart LED lamp should begin to flash quickly. If this
is not the case, quickly turn the lamp ON and OFF three
times using the light switch.
•Now open the Hama Smart Solution app and log in.
•Press +in the upper-right corner (Pic 1) to add a new
device.
•Select Lighting in the list.
•Now confirm that the lamp flashes quickly (Pic 2).

6
•.
Pic 1 Pic 2
•Next enter your WiFi password and confirm with OK.
•Your lamp will now be connected.
Pic 3 Pic 4
•Once the connection has been established, the lamp
stops flashing and the app confirms that your lamp was
connected. You can now give your lamp a name.
•Click Finish (Pic 4) to complete the process.
•Now you can control the lamp.
•Various options are available to you (see Pic 5):
-White Mode (Pic 6)
Setting the brightness
-Colour Mode (Pic 7)
Colour selection using the outer ring
Setting the saturation of the selected colour
Setting the brightness of the selected colour
-Scene Mode (Pic 8)
Selection of various light colour modes, for example,
reading or night mode
Pic 5 Pic 6
Pic 7

7
4.2 WiFi wallswitch
4.2.1 Product features
Safety Notes
•Small splinters of glass can lead to injuries if touched.
Dispose of the product immediately if it is damaged or
splintered during application or use.
•Only touch the damaged or splintered product on
undamaged areas and the edge.
•Be very careful while doing so, thoroughly wash your
hands afterwards and avoid contact with face and eyes.
Warning
•Do not use any heat-generating devices (such as
electric blankets, coffee machines, etc.) with this
product. There is a risk of fire and injury.
•Do not use this product with any devices that are
motorised or any devices that have a rotating
component or workpiece. There is a risk of injury.
•The device may only be operated on a 230 V 50 Hz
AC voltage supply. Work with the 230 V mains supply
may only be carried out by electricians certified in your
country. The applicable accident prevention regulations
are to be observed.
•To avoid an electric shock from the device, please
disconnect the mains voltage (switch off circuit
breaker). Failure to observe the installation instructions
can cause fires or other hazards.
Risk of electric shock
Do not open the product. Do not continue to operate
the product if it is damaged, which may be indicated by
smoke, odour or loud noises. Immediately contact your
dealer or our service department (see item “Service and
Support”).
This WiFi wall switch controls up to two ceiling lamps in
the home (switch on/off). Existing wall switches can be
simply replaced with it; maximum total load of 1000 W.
The following voice command is available:
•Turn on/off
‘Alexa/OK Google, turn on/off the light in the living room.’
4.2.2 Mounting
•Switch off the fuse (fuse box) that corresponds to the
room in which you want to install the switch.
•Verify that the wires are dead using a suitable measuring
device (for example, multimeter).
•Connect the WiFi touch wall switch as illustrated below:
•
L IN
neutral
Lamp 2Lamp 1
Install the switch in a suitable in-wall or surface-mount
box.
•Put the glass cover back onto the switch, and check
whether the cover has snapped firmly into place.
4.2.3 Integrating devices in the Hama Smart Solu-
tion app
•Switch the fuse back on.
•The two buttons should now flash, alternating between
blue and red.
•If this is not the case, touch one of the switches for
longer than 5 seconds.
•Now open the Hama Smart Solution app and log in.
•Press +in the upper-right corner to add a new device.
•Select Switches in the list.
•Now confirm that the control light flashes quickly.
•Next enter your WiFi password and confirm with OK.
•The WiFi touch wall switch will now be connected.

8
•The control light stops flashing and the app confirms that
your wall switch was connected. You can now give the
wall switch a name.
•Click Finish to complete the process.
•You can now control the WiFi wall switch with the app.
4.3 WiFi Power Socket/Power Strip
4.3.1 Product features
Safety Notes
Risk of electric shock
•Do not open the product. Do not continue to operate
the product if it is damaged, which may be indicated
by smoke, odour or loud noises. Immediately contact
your dealer or our service department (see item
“Service and Support”).
•Do not use the product if the
AC adapter, the adapter cable or the mains cable are
damaged.
•Do not attempt to service or repair the product
yourself. Leave any and all service work to qualified
experts.
Warning
•Only connect the product to a socket that has been
approved for the device. The socket must be installed
close to the product and easily accessible.
•The product has replaceable fuse. Always replace this
fuse with the same type of fuse with the same electrical
values.
•When using a multi-socket power strip, make sure that
the sum power draw of all the connected devices does
not exceed its maximum throughput rating.
•If you will not be using the product for a long period
of time, disconnect it from mains power.
Warning
•Do not use any heat-generating devices (such as
electric blankets, coffee machines, etc.) with this
product. There is a risk of fire and injury.
•Do not use this product with any devices that are
motorised or any devices that have a rotating
component or workpiece. There is a risk of injury.
•Never connect multiple units of this product in series.
This WiFi socket controls electrical devices (for example, a
floor lamp) in the home (switch on/off).
The following voice command is available:
•Turn on/off
‘Alexa/OK Google, turn on/off the light.’
4.3.2 Integrating devices in the Hama Smart
Solution app
•Connect the Wifi socket adapter or the wifi power strip to
a properly installed and easily accessible mains socket.
•Press and hold the button on the front side for approx. 5
seconds until the blue LED begins to flash quickly.
•Open the Hama Smart Solution app and log in.
•Press +in the upper-right corner to add a new device.
•Select ‘Sockets’ or ‘Multiple Sockets’ in the list.
•Now confirm that the LED flashes quickly.
•

9
•Next enter your WiFi password and confirm with OK.
•Your power socket will now be connected.
•Once the connection has been established, the LED stops
flashing quickly and the app confirms that your socket
was connected. You can now give the socket a name.
•Click Finish to complete the process.
•You can now control the WiFi Smart socket.
4.4 WiFi Door / Window Contact
4.4.1 Product features
This WiFi door/window contact is used for monitoring
(push message to smartphone on triggering) and querying
the status of windows and doors (open/closed).
The following voice command is available:
•Status query
‘Alexa/OK Google, is my window/door open/closed?’
Battery compart-
ment closure
Pairing-
button Manipulation protectionLED
4.4.2 Mounting
•We recommend attaching the sensor on the window or
door frame and the device directly on the window or door.
•Ensure that the markings (triangles) on the device and
the sensor are lined up and separated by no more than
10 mm when the door or window is closed.
Device Sensor
•You can fix the device and the sensor with screws, or
attach them using adhesive pads.

10
•If a door leaf or window sticks out, the sensor can also
be attached at the side, and the device can be attached
flat on the frame.
Warning - Installation with adhesive pad
•All parts are intended for indoor use only. Do not
install them outdoors.
•Please note that the installation surface you choose
should be free of dust and grease. Use a suitable clean-
ing agent from a specialised dealer to clean the surface.
•Note that the adhesive pad attachment is permanent.
To remove the adhesive pad, carefully pull it off the
installation surface.
•Various environmental factors such as ambient
humidity, sunlight or cold can impair the durability of
the adhesive pad.
•We cannot guarantee that residue will not be left on the
mounting surface after the adhesive pad is removed.
4.4.3 Integrating devices in the Hama Smart Solu-
tion app
Now insert the two AAA batteries supplied, observing
correct polarity. When you press the anti-theft protection,
the LED should briefly light up blue; if not, please replace
the batteries
Warning - Batteries
•When inserting batteries, note the correct polarity (+
and - markings) and insert the batteries accordingly.
Failure to do so could result in the batteries leaking or
exploding.
•Only use batteries (or rechargeable batteries) that
match the specified type.
•Before you insert the batteries, clean the battery
contacts and the polar contacts.
•Do not allow children to change batteries without
supervision.
•Do not mix old and new batteries or batteries of a
different type or make.
•Remove the batteries from products that are not being
used for an extended period (unless these are being
kept ready for an emergency).
•Do not short-circuit batteries.
•Do not charge batteries.
•Do not throw batteries in a fire.
•Keep batteries out of the reach of children.
•Never open, damage or swallow batteries or allow
them to enter the environment. They can contain toxic,
environmentally harmful heavy metals.
•Immediately remove and dispose of dead batteries
from the product.
•Avoid storing, charging or using the device in extreme
temperatures and extremely low atmospheric pressure
(for example, at high altitudes).
•Now press the Pairing button for 5 seconds. The LED
begins to flash red quickly. If it flashes slowly, press the
button again for 5 seconds.
•Open the app and log in.
•Press +in the upper-right corner to add a new device.
•Select Sensors in the list.
•Now confirm that the LED flashes quickly.

11
•Next enter your WiFi password and confirm with OK.
•Your sensor will now be connected.
•Once the connection has been established, the LED stops
flashing quickly and the app confirms that your sensor
was connected. You can now give it a name.
•Click Finish to complete the process.
•You can now fit the sensor and then configure it.
4.5 WiFi Motion Detector
4.5.1 Product features
This WiFi motion detector can be used for monitoring (push
message to smartphone on triggering) or for controlling
other smart products (for example, lamps).
Micro-USB-
port
Pairing
button
LED

12
4.5.2 Mounting
Warning
•Before mounting, check that the wall you have chosen
is suitable for the weight to be mounted. Also make
sure that there are no electric, water, gas or other lines
running through the wall at the mounting site.
•Buy special or suitable installation material from a
specialised dealer for wall-mounting.
•You can fix the sensor with screws, or attach it using an
adhesive pad.
Warning - Installation with adhesive pad
•All parts are intended for indoor use only. Do not
install them outdoors.
•Please note that the installation surface you choose
should be free of dust and grease. Use a suitable clean-
ing agent from a specialised dealer to clean the surface.
•Note that the adhesive pad attachment is permanent.
To remove the adhesive pad, carefully pull it off the
installation surface.
•Various environmental factors such as ambient
humidity, sunlight or cold can impair the durability of
the adhesive pad.
•We cannot guarantee that residue will not be left on the
mounting surface after the adhesive pad is removed.
•The sensor can be powered using batteries or mains
power (via USB).
•For battery operation, untwist the back of the product
anti-clockwise to open the battery compartment. Now
insert the two CR123A batteries supplied, observing
correct polarity.
Warning - Batteries
•When inserting batteries, note the correct polarity (+
and - markings) and insert the batteries accordingly.
Failure to do so could result in the batteries leaking or
exploding.
•Only use batteries (or rechargeable batteries) that
match the specified type.
•Before you insert the batteries, clean the battery
contacts and the polar contacts.
•Do not allow children to change batteries without
supervision.
•Do not mix old and new batteries or batteries of a
different type or make.
•Remove the batteries from products that are not being
used for an extended period (unless these are being
kept ready for an emergency).
•Do not short-circuit batteries.
•Do not charge batteries.
•Do not throw batteries in a fire.
•Keep batteries out of the reach of children.
•Never open, damage or swallow batteries or allow
them to enter the environment. They can contain toxic,
environmentally harmful heavy metals.
•Immediately remove and dispose of dead batteries
from the product.
•Avoid storing, charging or using the device in extreme
temperatures and extremely low atmospheric pressure
(for example, at high altitudes).
•For USB operation, connect a Micro-USB cable (not
included in delivery) to the Micro-USB port and to a suit-
able USB power supply (not included in delivery). Plug
the power supply into an easily accessible power socket.
When powering the device using a USB power supply,
make sure there are no batteries inside the device.

13
4.5.3 Integrating devices in the Hama Smart Solu-
tion app
•The LED begins to flash blue quickly. If it flashes slowly or
not at all, press the Pairing button for 5 seconds.
•Open the app and log in.
•Press +in the upper-right corner to add a new device.
•Select Sensors in the list.
•Now confirm that the LED flashes quickly.
•Next enter your WiFi password and confirm with OK.
Your sensor will now be connected.
•Once the connection has been established, the LED stops
flashing quickly and the app confirms that your sensor
was connected. You can now give it a name.
•Click Finish to complete the process.
•You can now fit the sensor and then configure it.
4.6 WiFi camera
00176576 / 00176577
Reset
SD card slot
Microphone
Speaker
Status light

14
00176566
Status light
Reset
Speaker
Micro USB
Microphone
SD card slot
4.6.1 Product features
•Status LED is constantly lit red: Preparing for pairing
mode
•Status LED flashes red: Pairing mode active (device can
be connected)
•Status LED flashes blue: QR code was recognised
•Status LED is constantly lit blue: Connection set up
successfully
Note
•Protect the product from dirt, moisture and
overheating, and only use it in a dry environment.
•Connect the product only to a socket that has been
approved for the device. The socket must be installed
close to the product and must be easily accessible.
•Do not attempt to service or repair the product yourself.
Leave any and all service work to qualified experts.
•Do not continue to operate the device if it becomes
visibly damaged.
•The product is intended for indoor use only.
•Keep this product, as all electrical products, out of the
reach of children!
4.6.2 Installation
•You can attach the camera using adhesive pads.
•Power can be supplied to the camera only via USB.
•For USB operation, connect a Micro-USB cable (included
in delivery) to the Micro-USB port and to a suitable USB
power supply (included in delivery). Plug the power
supply unit into a socket. Connect the product only to a
socket that is approved for the device. The socket must
be installed close to the product and must be easily
accessible. When powering the device using a USB
power supply, make sure there are no batteries inside
the device.
Warning - Installation with adhesive pad
•All parts are intended for indoor use only. Do not
install them outdoors.
•Please note that the installation surface you choose
should be free of dust and grease. Use a suitable clean-
ing agent from a specialised dealer to clean the surface.
•Note that the adhesive pad attachment is permanent.
To remove the adhesive pad, carefully pull it off the
installation surface.
•Various environmental factors such as ambient
humidity, sunlight or cold can impair the durability of
the adhesive pad.
•We cannot guarantee that residue will not be left on the
mounting surface after the adhesive pad is removed.
4.6.3 Integrating devices into the Hama Smart
Solution app
•Connect the WiFi camera to the USB cable supplied and
the power supply unit. Plug the power supply unit into
a socket.
•Wait a moment until the camera emits a signal tone and
the LED begins to flash red.
•Open the app and tap ‘My home’ at the lower-left edge
of the screen.
•Then tap ‘+’ at the upper-right edge of the screen, select
the ‘Cameras’’.
•Tap ‘OK’ to confirm that the camera is flashing.
•Then enter the name of your WiFi network and the
password. Tap ‘OK’ to confirm your entries.
•Now scan the QR code with the camera. Tap ‘I heard
the beep’ to confirm that you heard a signal tone. The
camera will now be connected.

15
•Once the connection has been established, the LED stops
flashing quickly and emits a constant blue light; the app
confirms that your camera was connected. You can now
give the camera a name.
•Click ‘Finish’ to complete the process.
•Now you can attach the camera and set up, control and
configure it using the app.
•‘Screenshot’ allows you to take a snapshot.
•‘Speak’ allows you to speak via the camera.
•‘Record’ allows you to record the image currently shown
and store it in your gallery.
•‘Playback’ allows you to view past video recordings. They
are stored in encrypted form on an SD card (not included
in delivery), which must be inserted into the camera.
•‘Alarm’ allows you to access the motion detection
settings and configure them.
•‘Photo Album / Cloud Storage’ allows you to locate the
recorded images and videos.
Note - Pairing restart
Press and hold the Reset button on the back for
approximately 5 seconds until a signal tone sounds.
As soon as the LED begins to flash red, you can make
another pairing attempt.
4.7 WiFi controller for LED strips
4.7.1 Product features
Note
•Protect the product from dirt, moisture and
overheating, and only use it in a dry environment.
•Operate the product only with a mains plug that is
approved for the device, and connect it to a socket
approved for the device. The socket must be installed
close to the product and must be easily accessible.
Risk of electric shock
•Do not use damaged or unsuitable power supply units
or LED light strips.
•When changing LED light strips, always ensure that the
LED light strip in question is current-free. Switch off the
current and/or pull the mains plug.
•Do not open the product. Do not continue to operate
the product if it is damaged, which may be indicated
by smoke, odours or loud noises. Contact your dealer
or our service department immediately (see „Service
and support“).
4.7.2 Installation
•Connect the WiFi controller to an LED light strip. Make
sure that the polarity is correct: The arrow on the plug
indicates that the contact that must be connected to the
12 V contact of the LED light strip. Please also refer to
the operating instructions for the LED light strip used.
•Then connect the controller to a properly installed and
easily accessible power socket via a power supply unit.
Please refer to the operating instructions for the power
supply unit used.
Warning
•Use this product only with power supply units and
LED light strips (GRB, BRG) that are approved for
the application. To this end, check the technical
specifications of the power supply unit, LED light strip
and WiFi controller for compatibility.
•Before carrying out the installation, check that the
power supply unit and LED light strip are in perfect
technical condition.
•Please note that lights (even LEDs) can generate heat
and may become hot. Always let the light cool off for a
few minutes before touching it or changing it.
•Disconnect the product from the mains if it will not be
used for a long period of time.

16
4.7.3 Integrating devices into the Hama Smart
Solution app
•Connect the WiFi controller to an LED light strip. Make
sure that the polarity is correct: The arrow on the plug
indicates that the contact that must be connected to the
12 V contact of the LED light strip. Please also refer to
the operating instructions for the LED light strip used.
•Then connect the controller to a properly installed and
easily accessible power socket via a power supply unit.
Please refer to the operating instructions for the power
supply unit used.
•The LED light strip begins to flash quickly. If this does
not happen, quickly disconnect and reconnect the power
supply unit three times.
•Open the Hama Smart Solution app and tap ‘My home’
at the lower-left edge of the screen.
•Then tap ‘+’ at the upper-right edge of the screen.
Select the ‘Lights’ category.
•Tap ‘OK’ to confirm that the LED light strip is flashing
quickly.
•Then enter the name of your WiFi network and the
password. Tap ‘OK’ to confirm your entries.
•The WiFi controller is now connected to the app. Once
the connection has been established, the LED light strip
stops flashing. You can now give the controller a name.
•Click ‘Finish’ to complete the process.
•You can now set up, control and configure the WiFi
controller using the app.
•‘White’ allows you to specify that white light should be
emitted.
•‘Color’ allows you to change the colour, brightness and
saturation of the light strip.
•‘Scene’ allows you to set up automated colour changes.
•‘Music’ allows you to make the LED controller react to
background music.
•‘Schedule’ allows you to schedule when the light strip
automatically switches on.
Note
If the colours blue and green are displayed in the
opposite sequence to in the app, disconnect the
controller from the power, and connect the supplied
adapter cable between the controller and the LED light
strip.
5. Timer, automation and 1-click control
5.1. Timer*
To access the Timer area, click the Schedule button.
Here you can program the device to switch on or off at
particular times.
•Press Add Timing.
•In the upper area, select the desired time; then select
whether you would like to execute the command
repeatedly and, lastly, whether the smart product should
switch on or off at this time.
•Confirm your programming by pressing Save in the
upper-right area.
•You can also add a comment and have an execution
message output on your mobile phone.
* Does not apply to the window/door contact 00176553,
the motion detector 00176554 or the camera 00176566

17
5.2 1-click control and automation
•1-click control is used to control multiple devices with
one click, or by voice command with an AI speaker.
With automation, tasks and settings can be executed
automatically based on conditions (for example, sunset
at 19:00 hrs ¨ floor lamp controlled using smart socket
switches on).
•Press Smart in the bar at the bottom and then press + in
the upper-right area.
•You are now on the ‘Create Smart’ screen.
•If you press ‘Launch Tap to Run’, you will access the
screen for setting up the tasks for 1-click control.
•If you tap ‘When the weather changes’, ‘Schedule’
or ‘When the device status changes’, then you can
select a condition for the execution of the automation.
Various possibilities are available here. With ‘When the
device status changes’, you can set, for example, the
smart motion detector 00176554 so that a task can be
executed when movement is detected.
•The tasks for 1-click control and automation are set up in
exactly the same way. Here, you can select between three
possibilities for 1-click control, and four for automation.
•‘Run the Device’ allows you to select a device from those
you have integrated into the app, and have it switch on
or off automatically.
•‘Select Smart’ allows you to execute/activate a scene
(1-click control) or an automation.
•For an automation, you can also have a push notification
sent to your mobile phone (for this purpose, select ‘Send
Notification’). You therefore receive a notification when
the automation is executed.
•‘Delay’ allows you to select a time that is to elapse
before another action is executed.
•If, after selecting the task, you press ‘Next’ in the upper-
right area, you are taken to a ‘Smart Setting’ screen, in
which your selected conditions/prerequisites (only for
automation) and tasks are shown ordered. Now you can
select further prerequisites/states, and specify whether
only one of the states, or all of them, must be fulfilled
for the automation to be executed. If you scroll down,

18
you can also add new tasks, or move a task by pressing
and holding on it. By moving a task to the left, you can
delete it.
•‘Name’ allows you to give your 1-click control or
automation a name.
•‘Style’ allows you to assign a colour and a picture to your
1-click control or automation, which are subsequently
displayed in the app.
•‘Effective Period’ allows you to select the times at which
your 1-click control or automation can be executed, and
the days on which it is effective.
6. Integration in Amazon Alexa
A detailed guide on connecting your smart products to
Alexa can be found at www.amazon.co.uk, under ‘Connect
Smart Home Devices to Alexa’ in the Help. Follow the
instructions there.
Note - Groups and scenes (Alexa app)
•If you have already created groups and/or scenes in the
Hama Smart Solution app, you might not be able to
use them in the Alexa app.
•It is only possible to group lamps with the Alexa app;
scenes are not possible.
7. Integration in Google Home
•Install the Google Home app from the Google Play Store.
•Log into the app.
•Grant the necessary permissions to the app.
•To integrate the products, click on the +in the top left
corner (Pic 9).
•Then select Set up device.
•Now click the category Have something already set
up? (Pic 10) (If necessary, the app will now update.)
•Now select Hama Smart Solution (Pic 11) in the list
and log in with the data for your app.
•Confirm with Link now (Pic 12), and in the next list
confirm Hama Smart Solution once more (Pic 13).
•Click Link now (Pic 14), then Authorize (Pic 15), and
your accounts will be linked.
•Finally, you can rename your devices (for example: fan) or
assign them to individual rooms (for example: office).
•Now you can also use your voice and the Google Home
app to control your devices.
Pic 9 Pic 10
Pic 11 Pic 12
Pic 13 Pic 14

19
Pic 15 Pic 16
8. FAQs and support
How devices are networked
•Step 1: Add device
1. First ensure the power supply and then switch on the
device.
2. After opening the app, click ‘+’ at the top right of the
start page to add the device, enter the appropriate
page and select the corresponding product category.
3. Putting the device into network status:
The WiFi indicator flashes quickly (twice per second).
Above the ‘Confirmation indicator flashes’ button, you
will find the ‘Set fast flashing of indicator’ explana-
tion, which explains how to proceed.
In the case of products that have a switch (such as the
socket, for example) but no reset button, you normally
press and hold the switch for 5 seconds.
In the case of lamps that do not have their own
switch, you twist them into the corresponding fixture,
press the light switch three times (‘On-Off-On-Off-On-
Off-On’) and leave the device switched on. The process
is completed as soon as the lamp flashes quickly.
If the product has a reset button, normally you simply
have to press it.
You may find it useful to refer to the operating instruc-
tions of the actual product, in order to find out about
the network integration settings.
Step 2: Entering the WiFi password
Select the WiFi network that the device is to connect
to. Enter the WiFi password and then click ‘OK’ to call
up the network settings. Only 2.4 GHz WiFi is currently
supported for the network integration. Check whether,
in your case, the network is a 2.4 GHz network.
The network connection is displayed after a few
seconds.
How to troubleshoot connection errors (device
integration has failed)
1. Make sure that the device is supplied with power and
is switched on.
2. Make sure that the device is in network state.
3. Make sure that the device, smartphone and router are
close together.
4. Make sure that the router and smartphone have a
network connection.
5. Make sure that you have entered the correct router
password.
6. Make sure that the device you want to integrate into
the network is using the 2.4 GHz WiFi band. WiFi
must be activated and must not be set to hidden.
7. Make sure that the WiFi encryption mode configured
for the router is WPA2-PSK, the authentication type
is AES, or both are set to automatic. The WiFi mode
must not be set to 11n only.
8. If the maximum number of devices that can access
the router has already been reached, you can try
deactivating the WiFi function of a device in order to
reconfigure the channel.
9. If WiFi MAC address filtering is activated on the
router, try removing the device from the router’s MAC
filter list to ensure that the router does not block the
device from the network.
What should I do if the device is displayed as
offline?
1. Make sure that the device is supplied with power.
2. Make sure that the network the device is on is stable.
How to check the status: Integrate your smartphone
or tablet into the same network and lay it next to the
device. Try to open the Web page.
3. Make sure that the WiFi home network functions prop-
erly, and check whether the WiFi name, the password,
etc., were changed. If this is the case, please reset the
device and add it again. Removing a device: Open the
app to access the device control page, click the ‘...’
button in the top-right corner to display further pages,
and click ‘Delete device’ at the end of the page.
4. After the router has restarted, wait 3 minutes to see
the device status.
5. If the network status has not changed after trouble-
shooting, go to the device’s control page and click the

20
‘...’ button in the top-right corner to display further
pages. Click ‘Feedback’ to specify the problem that
has occurred and your router model.
Using the app
The app cannot remotely control the device; after the
remote control attempt, the settings are not applied.
If the app control does not work, this can be due to the
network, or the device may not be connected to the
network.
1. Make sure that the device is supplied with power.
2. Leave the app open for about 3 minutes to check
whether the device status is still online.
3. If you are still online, lay your smartphone next to the
device, connect it to the same WiFi network as the
device, and try opening the Web page to determine
whether the network is functioning properly.
4. If control is not possible even though the device is
on the network and network reception is good, go
to the device’s control page and click the ‘...’ button
in the top-right corner to display further pages. Click
‘Feedback’ to specify the problem that has occurred
and your router model.
Once the device is connected to the network, the
control works at the same location, but as soon as
the smartphone changes its network address or
a different network is used, the control no longer
works.
Under these circumstances, it is possible that the device
and the smartphone are connected via the same local area
network, but are not connected to the Internet.
1. Lay your smartphone next to the device, connect it to
the same WiFi network as the device, and try opening
aWeb page to determine whether there is an active
Internet connection.
2. If you have no Internet access, try restarting the router.
3. If the device is connected to the Internet but the prob-
lem described above still occurs, go to the device’s
control page and click the ‘...’ button in the top-right
corner to display further pages. Click ‘Feedback’ to
specify the problem that has occurred and your router
model.
The actual device status does not correspond to the
status displayed in the app
If the device is controlled by a physical switch, it is possible
that the device status cannot be immediately synchronised
through opening of the app.
Open the app again. The device status should now update
in operation.
After the power supply of the lamp has been interrupted
and then restored, the light that was originally switched off
suddenly switches on.
In this case, the lamp itself does not have a switch (and the
house switch is not controlled through intelligent network-
ing, and the scene settings are not activated). When such
a device is connected to the network, the lamp’s physical
switch must be turned on before the app is able to control
the lamp. If, however, the power supply is interrupted, the
connection between the lamp and app is also interrupted.
As aresult, the lamp becomes a standard lamp again. If
the power supply is now restored, the ‘On’ physical switch-
ing state applies, meaning the light is switched on.
How can I deactivate a countdown after it has been
set?
Set the countdown to 0 hours 0 minutes; this will deacti-
vate it.
Switch the temperature display between Celsius
and Fahrenheit.
Open the personal settings in the app, click the profile
image to open the page with the basic settings, and
select the desired unit under ‘Temperature unit’. After the
change, the selected temperature unit is used in accord-
ance with the subsequent settings scene.
What should I do if ‘SmartLife-xxxx’ cannot be
found in the network when using compatibility
mode?
Search in the WiFi list for ‘undefined-xxxx’ or other similar
hotspot types, in order to establish a connection.
Third-party controls
How do I check which controls of third-party providers are
supported by my device?
First register the device in the app, then go to the device
control page. Click the ‘...’ button in the top-right corner
to display further pages. In ‘Supported third-party control’,
you can display the third-party control supported by the
device. Here you can click the symbol for the third-party
control to view the user guide.
What do I do if voice control does not work for third-party
products in spite of a connection?
Please check in the third-party app whether the command
was correctly recognised. Further information can be found
in the operating instructions of the third-party provider.