Hamy KT-2418 Technical manual

1
2.4GHz WIRELESS RECEIVER &
QUAD SYSTEM
KT-2418
Operation Instruction

2
I. Summary
Respectable users: we appreciate that you have chose the color 4-channel
multiplexer of our company, this manual will introduce the functional features,
installation and operation method of the product to you, so that you will get
acquainted with our product as soon as possible.
Notes: the information in the manual is the information when the manual is
published, the manufacturer will reserve the rights to modify and improve the product,
and any modifications to the parameters will be made without any notification.
It is prohibited to use the product under the environment of high temperature and
high moisture, especially in shower room under high temperature;
Don’t put the product at the places under direct sunshine (such as vehicles which
are parked on open areas and sand beach);
Don’t wash and wipe the product with diluent or other chemical detergent;
Only the specified AC adapter and power source can be used; don’t use other
power sources, to avoid causing serious damage to the product;
Please cut off the power source when the product is not used;
Don’t disassemble the product without permission, please contact the distributor
or our company in case of any doubts.
2. Key Functional Features
Time and date display and location setup
Camera name setup
Auto sequence
Camera picture quality setup
Monitoring 4x electronic zoom function
Connect PC, a single synchronous recording or four camera signals

3
II. Instruction for Wire Connection
Insert the yellow video cable and red audio cable into the VIDEO and AUDIO IN
of TV set or monitor.
And the picture you receive will display on the TV set or monitor. Select AUDIO
CH, and you will receive the voice from your wireless camera synchronistically.
connects to the USB line can be displayed on a computer on-site
audio-video receiver, and synchronization of audio and video
recording scene
III. Instruction for Keys and Operation
Schematic Drawing for Panel:
Schematic Drawing on the Back:

4
1. QUAD/MENU Key:
(1) Press QUAD Key under the current non-menu setup mode and the status of
auto sequence to enter into current quad picture;
(2) Press and hold MENU Key under the current status to return to the menu
picture;
(3) Press this key to return to the higher level menu or exit the main menu in
menu operation.
2. AUTO/FREEZE Key:
(1) Press this key under the current status of QUAD to enter into auto sequence
function, and it will cycle automatically in the sequence of
QUAD-CH1-CH2-CH3-CH4 according to the set sequence time.
(2) Press this key under current PIP1 status, and the small picture will cycle
automatically in the three channels except the big picture.
(3) Press and hold FREEZE Key under the mode of quad and big picture display
to enter into small picture freeze status, and “F1234” will be shown on the
top left corner of the display, and “1234” will be shown in light color; press
CH1, CH2, CH3 and CH4 Keys, the picture of the corresponding camera 1,
2, 3 and 4 will be frozen, and the corresponding figures on the top left corner
will become flashing, press this key again or when the freeze time ends, the
freeze of the picture will be cancelled.
3. MODE/ZOOM Key:
(1) Press MODE Key under the current status, the picture will be switched in the
sequence of PIP1-PIP2-PIP3-POP-QUAD;
(2) Press and hold ZOOM Key to enter into electronic zoom function, and you

5
may adjust the scope of zoom through “▲”, “▼”, “ +” and “—” keys; press
AUTO Key after selecting the scope, and the selected scope will be zoomed to
quadruple the original;
(3) Press and hold CH1, CH2, CH3 and CH4 after entering into ZOOM function
to zoom the corresponding quad picture to quadruple the original;
(4) Press ENTER Key After zoom to exit the zoom status, and return to the zoom
zone selection status;
(5) Press ZOOM or QUAD to return to the original status.
4. “ENTER” Key: under the menu status, this key functions as carriage return; press
this key after selecting menu to enter into the selected submenu.
5. “1”, “2”, “3”, “4”/“▲”, “▼”, “+” , “—” Keys
(1) These four keys may be used to display or freeze the picture of the
corresponding camera in the current quad picture display;
(2) Under the menu selection mode, these four keys may be used to move the
position of the cursor upwards and downwards and change the value of the
corresponding cursor.

6
IV. Command Setup under Menu
You can enter into the main menu if pressing MENU in any current display mode;
Operation instruction: press (▲) Key or (▼) Key when setting menu and selecting
setup window, and the cursor will move downwards and upwards on the selected
options, press (+) or (—) Key to conduct parameter modification setup; press MENU
to save the set parameters and return to the lower level menu; press and hold MENU
to exit the menu.
1. SYSTEM SETUP (Setup of time, date, system and reset)
Press “ENTER” to enter into setup option after selecting SYSTEM SETUP with
“▲” and “▼” under the main menu mode.

7
(1) DATE: system date, YY-MM-DD (year, month and date) arrangement; press
“▲” and “▼” keys for a selection at first and then press “—” and “+” keys to
modify the sequence of the arrangement (MM-DD-YY); press “▲” and “▼”
keys to select the date and then press “—” and “+” keys to modify/set the date;
(2) TIME: system time, HH:MM:SS (hour, minute and second) setup; press “▲”
and “▼” keys for a selection at first and then press “—” and “+” keys to modify
the sequence of the arrangement (MM-SS-HH); press “▲” and “▼” keys to
select the clock and then press “—” and “+” keys to modify/set the time;
(3) SYSTEM FORMAT: color system setup, use control key to select the two
systems of “PAL” or “NTSC”;
(4) SYSTEM ID NUMBER: system ID number setup (unavailable in this product);
(5) KEY LOCK: key lock, when “ON”is selected, the keys other than
MENU/QUAD Key are unavailable under current mode; when “OFF”is
selected, the key function will be recovered and available under current mode;

8
(6) FACTORY RESET: system reset, when “YES”is selected, press “ENTER”to
recover the system to factory setup status; “NO”means unrecoverable.
2. DISPLAY SETUP: display setup
1）DISPLAY ON SCREEN: display on screen
(1) TITLE: camera title switch, “∨”is on;
(2) DATE: date display switch, “∨”is on;
(3) TIME: time display switch, “∨”is on;
2) SCREEN POSITION: screen row/field display
(1) X: row center display;
(2) Y: field center display.
3) BORDER COLOR: border parting line color
(1) BLACK: black;
(2) GRAY1: grey;
(3) GRAY2: off white;
(4) WHITE: white;

9
(5)OFF: off, when “OFF”is selected, the scene will not be divided by border line.
3. AUTO SEQUENCE: auto switch setup
1) QUAD: means the picture sequence time setup mode of QUAD and CH1-CH4;
2) CAMERA1: set the time for image to stay in CH1;
3) CAMERA2: set the time for image to stay in CH2;
4) CAMERA3: set the time for image to stay in CH3;
5) CAMERA4: set the time for image to stay in CH4.
4. CAMERA SETUP: camera setup

10
1) CAMERA: the channel needed to be set;
2) TITLE: title setup mode, when this option is selected, figures and letters on the
top of screen can be edited;
3) BRIGHTNESS: brightness adjust
4) CONTRAST: contrast control
5) SATURATION: hue control;
6) HUE: saturation control;
7) SHARPNESS: sharpness control
8) MIRRORING: image mirroring switch.
5. MOTION SETUP: motion alarm setup

11
1) CAMERA: set channel
2) DETECTION TIME: ALWAYS ON: alarm is on, ALWAYS OFF: alarm is off;
ON/OFF TIME: set alarm time (now ON: 11:00 OFF: 12:00 available)；
3) SENSITIVITY: detection sensitivity setup;
4) VELOCITY: alarm velocity setup;
5) MASKINGAREA: detected area coordinate (X ．Y: 00．00);
6. EVENT SETUP: alarm setup (it is proposed not to open it in this product)

12
1) ALARM: external alarm switch, it is on when “∨” appears if pressing ENTER
Key after selection;
2) LOSS: video loss switch, it is on when “∨” appears if pressing ENTER Key after
selection;
3) MOTION: motion detection switch, it is on when “∨” appears if pressing
ENTER Key after selection;
4) BUZZER HOLD TIME: the hold time of buzzer (no buzzer in this product);
5) REPORT HOLD TIME: the hold time of event record;
6) ALARM POLARITY: the high and low potential setup of buzzer alarm, “LOW”
is low, and “HIGH” is high.
7. EVENT REPORT: alarm records (totaling 6 pages)

13
1) NO: serial number of alarm;
2) YY-MM-DD: date of alarm;
3) HH:MM:SS: time of alarm;
4) CH: channel of alarm
5) EVENT: event of alarm;
6) LIST CLEAR: to clear records, set “NO” as “YES” and then press ENTER Key to
confirm completion of clear.

14
V. Technical Parameters:
System
PAL NTSC
Receiving Frequency
CH1:2.414GHz CH2:2.432GHz,
CH3:2.450GHz CH4:2.468GHz
Source Voltage
12V 1.2A
Current Consumption
750mA
Receiving Sensitivity
-88dBm
Antenna Input Impedance
75 ohm
Video Output Level
1Vp-p
Audio Output Level
1Vp-p
Image Resolution
720×576(PAL)720×480(NTSC)
Image Refresh Rate
60Hz/second(NTSC)50Hz/second(PAL)
Video Output Type
Single picture, two picture, PIP,
POP or four picture can be
displayed and switched
automatically
Ambient Temperature
-30°C-60°C
Interface type
USB 2.0
Coding manner
MPEG
Software attached
Application attached
Support operation systems
win98/ME/2000/XP
Highest image resolution
1440*1152
VI. Requirements of system

15
CPU：1.8GHZ or up
RAM:256M or up
Hard disk:10GB
Operation system:win2000,winXP
USB 2.0 port
VII. Install driver:
Connect this unit to a computer and install USB2.0 driver
1.Find the file STK1160 Driver in the disk, open it, click“Setup start driving
installation .
2.If this product is connected to your computer, disconnect it. Click“OK”to continue.
3.Click“Install”.

16
4.Click“Continue Anyway”to next.
5. Click “Finish”to end the installation to driver
6.After clicking“Finish”, there is a picture diction, click“OK”, and connect the
product to your computer to continue installing,

17
7.After connected, there is a dialogue, select“NO, not this time”, click“NEXT”.
8. Click“NEXT”.
9.Click“Continue Anyway”go to the next step
10.Click“Finish”. There is a reminder,“hardware has been installed and can be used”.
Then go to monitor.

18
VIII. Installation of software:
1.Click the file“setup.exe”, click the following icon
2.Select relative language and click“OK”.
3．Click “NEXT”to continue.
4．Select relative destination location. Click “Next”to continue.

19
5．Click “Next”.
6．Click “Install”.
7．Click “Finish”. At this time, your software “Wireless Camera Watcher”has been
successfully installed.

20
X．Directions on operation of Wireless Camera Watcher:
For initial installation and operation, you should click high-level settings at first and then
click Image tab to select system (PAL/BDGHI NTSC/M) and input manner. If you are
using wireless camera orA/V IN, you should select “Group”.
Introduction of functions of buttons