Bluestream HEX11WP-RX User manual

HEX11WP-RX QUICK REFERENCE GUIDE
Contact: [e-mail] |[e-mail] |[e-mail]
HEX11WP-RX
Quick Reference Guide
01
Our HEX11WP HDMI Wall Plate HDBaseT™ Receiver is a 4K solution designed to
receive a HDBaseT™ signal from a compatible HDBaseT™ transmitter up to 70m
at 1080p (40m 4K 60Hz 4:2:0/4K 30Hz 4:4:4). The HEX11WP-RX has been designed
to work with all Blustream HDBaseT™ transmitter and matrix solutions, be
installed in both UK and European backboxes and can be powered locally or from
compatible Blustream HDBaseT™ products.
Introduction
FEATURES:
• Advanced HDBaseT™ technology oering distribution of video and audio over a single CAT cable
• Supports 4K UHD video up to 40m (3840 x 2160 @30Hz 4:4:4, 4096 x 2160 @24Hz 4:4:4, and 4K @60Hz 4:2:0)
• Extends HDMI at 1080p up to a distance of 70m
• Supports all known HDMI audio formats including Dolby TrueHD, Dolby Atmos, Dolby Digital Plus and DTS-HD
Master Audio transmission
• Supports CEC and RS-232 pass-through
• Supports bi-directional IR pass-through to compatible HDBaseT™ device
• Supports 12V-48V PoC from compatible Blustream HDBaseT™ transmitter / matrix products
• Compatible with all Blustream HDBaseT™ transmitter / matrix products*
• Magnetic faceplate surround allowing both UK & EU backbox compatibility
• HDCP 2.2 support
*Technical performance is subject to the features supported on the connected HDBaseT™ device.

HEX11WP-RX QUICK REFERENCE GUIDE
www.blustream.com.au |www.blustream-us.com |www.blustream.co.uk
02
Front Panel Description
1Power Status Indicator - Illuminates when powered
2HDBaseT™ Link Status Indicator - Illuminates when the receiver is connected to a HDBaseT™ transmitter / matrix
product successfully
3HDCP Status Indicator - Illuminates when signal being received supports HDCP
4IR Receiver Input - 3.5mm stereo jack to connect to Blustream 5V IR receiver (not supplied)
5HDMI Output - Type-A HDMI port to connect HDMI display device
6RS-232 - 3-pin Pheonix connector to connect to RS-232 port of display device for control
712V DC Input - 2-pin Phoenix connector to connect to Blustream 12V power supply (supplied)
8IR Out - 3.5mm mono jack to connect to Blustream 5V IR emitter (not supplied)
1HDBaseT™ Input - RJ45 HDBaseT™ port to connect to the HDBaseT™ input port of the compatible Blustream
HDBaseT ™ transmitter / matrix device
2
3 4
1
Rear Panel Description
1
5 6 7 8

HEX11WP-RX QUICK REFERENCE GUIDE
Contact: [e-mail] |[e-mail] |[e-mail] 03
RS-232 HDMI Infrared Cat 6 DC Power
HEX11WP-RX Example Schematic
HDMI Source
Control Processor
Display
Compatible Blustream HDBaseT™ Matrix or Transmitter product. *Technical performance is subject to the features supported on the connected HDBaseT™ device.
Optional PSU when not powered via HDBaseT™
40m Max (4K)
70m Max (1080p)
HEX11WP-TX
HEX11WP-RX
A
C
D
B
HDMI RS-232 IR PoC
A
B
C
D

HEX11WP-RX QUICK REFERENCE GUIDE
www.blustream.com.au |www.blustream-us.com |www.blustream.co.uk
04
Package Contents
Specifications
HEX11WP-RX
• 1 x HEX11WP-RX
• 1 x 12V/1A DC Power Supply
• 1 x Magnetic Faceplate
• 1 x Quick Reference Guide
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION - changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmentally safe recycling.
NOTE: Specifications are subject to change without notice. Weights and dimensions are approximate.
HEX11WP-RX
Video Input Connectors: 1 x HDBaseT™ RJ45 connector
Video Output Connectors: 1 x HDMI Type A, 19-pin, female
RS-232 Serial Port: 1 x 3-pin Phoenix connector
IR Input Port: 1 x 3.5mm stereo jack
IR Output Port: 1 x 3.5mm mono jack
Local Power Input: 1 x 2-pin Phoenix connector
Module Dimensions (W x H x D): 136mm x 76mm x 44mm (w/o faceplate)
Faceplate Dimensions (W x H x D): 146mm x 86mm x 6mm
Cut Out Dimensions (W x H x D): 78mm x 49mm x 37mm
Mounting Hole Spacing: UK 121mm CTC, EU 60mm CTC
Backbox Mounting Depth: 40mm (minimum), 47mm (recommended)
UK or EU double gang
Shipping Weight: 1.0Kg
Operating Temperature: 32°F to 104°F (-5°C to +55°C)
Storage Temperature: -4°F to 140°F (-25°C to +70°C)
Power Supply: 12V/1A DC
REVA1_QRG_HEX11WP-RX_210521
Certifications