HandyHeat 132 A User manual

DAY/HOUR/MIN - Set the day and clock setting.
PGM - Program the schedule (programs).
MODE - Select the operating mode.
RETURN - To exit a function.
To configurate temperature setpoints:
program when Automatic mode is enabled.
Current operating mode (auto / manual ). In
Auto mode , the program’s associated setpoint is
also displayed ( ).
Comfort , Economy and Vacation.
Adjust the floor temperature (AF only).
—Increase and decrease temperature.
—Indicates the number of the current
Indicates the room or floor temperature.
Heating indicators ( see “Temperature Control”
below).
HandyHeat 132-A
This model has been designed to control a room’s ambi-
ent temperature.
The HandyHeat 132-A has one temperature sensor loca-
ted in the control module.
HandyHeat 132-AF
This model is designed to use a floor sensor to control
the room temperature.
The HandyHeat 132-AF has two temperature sensors:
- The first one, installed in the control module, controls
the ambient temperature.
- The second one, installed in the floor (and connected
to the power base), limits the temperature of the floor
(the default setting of this limit is 28°C).
HandyHeat 132-F
This model is designed to control floor heating systems.
The HandyHeat 132-F has a temperture sensor installed
in the floor (sensor is connected to the power base).
HandyHeat 132 has two switches, located on the
upper-left part on the rear of the control module,
which are used to set the following options:
Early Start
When the Early Start function is enabled disabled
by default), HandyHeat 132 calculates the optimum
system start time to obtain the desired temperature
by the set time. To enable function:
Position switch #1 down.
Note: When this function is enabled,
the system can be activated before
the program’s start time.
Temperature Display
By default, HandyHeat displays the temperature in °C.
If you wish to change to °F.
Position switch #2 down.
Note: When you switch from °C to °F or vice
versa, the and setpoints must be
redefined.
,
Control Module
HandyHeat132 A/F/AF
Owner’s Guide
Thank you for choosing HandyHeat 132, a programmable
thermostat, that provides both energy savings and total
comfort.
HandyHeat 132 Description
Model Overview
Configure the Switches
Align the bracket tabs on the control module with the
holes located on top of the power base.
This control module must be installed on a PB130
series power base.
Note: Keep the thermostat’s air vents clean and free
from obstructions.
Note: The screw cannot be removed completely.
On the first installation , the screen displays:
0:00, MO, and temperature (room/floor).
For Floor Heating Installations:
One of the two following messenges may be
displayed when a problem occurs:
LO: The floor temperature is below 0°C,
the temperature sensor is defective, or not
connected.
The heating indicator is displayed and
the relay is closed ( energized ).
HI: The floor temperature is above 60°C,
or the temperature sensor is defective.
Set the time (HOUR - MIN).
Set the day (DAY).
If you remove the module from its base for more than
2 hours, the time and day will have to be reprogrammed.
Comfort and Economy Setpoints.
These setpoints are associated with the schedule’s pro-
grams (programs 1 &3 = Comfort, programs 2 & 4 = Eco-
nomy) and are preprogrammed as follows:
A & AF mode is - 20°C, 18°C
F mode is - 28°C, 20°C
To modify a setpoint:
Set the temperature using and press and hold
the or button until it is displayed on the
screen. Press MODE/RETURN to exit.
Vacation Setpoint
The vacation setpoint is associated to the Vacation opera-
ting mode and is preprogrammed to 10°C. To modify this
setpoint, repeat above step.
Floor Temperature Setpoint (AF mode only)
The floor temperature limit is preprogrammed to 28°C to
avoid damage to your floor.
To modify, press the adjustment button (below ) using a
pointed object, set the desired temperature using and
press MODE/RETURN to exit.
HandyHeat 132 offers three operating modes:
Automatic - Executes the schedule.
Press MODE to select . The current prog-
ram number is displayed.
You can temporarily pass the current prog-
ram by setting a specific temperature setpoint using
or by selecting one of the pre-defined setpoint
buttons . The new setpoint will be maintained
until the beginning of the next program.
Manual - Maintains constant temperature.
Press MODE to select .
Set temperature or selsct one of the pre-
defined setpoint buttons ( ).
Vacation - Maintains the Vacation setpoint
during a prolonged absence.
Press .
()
Install the Control Module
Power base
Control module
Air vents
Air vents
First Power ON
Set the Time and Day
Adjust the Temperature Setpoints
Select the Operating Mode
DVK-00079-001

The schedule is used with the Automatic mode. The
schedule controls the heating system to automatically
switch between the Comfort and Economy temperature
setpoints at the times you have programmed.
The schedule consists of 4 programs per day defined
as follows:
To enter the programs’ start time
To shorten programming, you simply should enter the
start time for each program.
Press PGM.
Press DAY to select the day (hold for 3
seconds to select all days of the week).
Note: It is sometimes faster to program the same schedule
for the entire week and then to modify the exception days.
Press PGM to select the program number (e.g. 1).
Press HOUR and MIN to set the start time.
Repeat steps 3 and 4 for remaining programs
(e.g. 2, 3 and 4)
Press MODE/RETURN to exit.
Note: After 60 seconds of inactivity, the thermostat will
automatically exit programming mode.
To clear a program time:
When you clear a program time entry, the HandyHeat 132
will maintain the temperature setpoint of the last executed
program until the beginning of the next program.
Repeat steps 1 to 3 above.
Press CLEAR to erase the time entry. The time
portion of the LCD indicates --:-- when the pro-
gram is inactive.
Press MODE/RETURN to exit.
Programming Examples
Comfort:
- Monday to Friday, between 6:00 and 8:30 and
between 16:00 and 23:30.
- Saturday and Sunday, between 6:00 and 23:00
Economy:
- Monday to Friday, between 8:30 and 16:00 and
between 23:00 and 6:00.
- Saturday and Sunday, between 23:00 and 6:00.
To program this schedule:
Press PGM.
Press and hold DAY for 3 seconds to select all
days of the week.
Press PGM to select program 1.
Set the time(6:00) using the HOUR and MIN
buttons.
Press PGM to select program 2.
Set the time (8:30) using HOUR and MIN buttons.
Repeat step 4 for remaining programs:
program 3 (16:00) and program 4(23:00).
When all programs are configurated, press MODE/
RETURN to exit.
To erase programs 2&3 for Saturday and Sunday:
Press PGM.
Press PGM to select program 2.
Press DAY to select Saturday (SA).
Press CLEAR to erase the time (--:--).
Press DAY to select Sunday (SU).
Press CLEAR to erase the time (--:--).
Press PGM to select program 3.
Repeat steps 3 to 6.
Press MODE/RETURN to exit.
Programs Setpoint Ti me
i. The programs’ start time can be different for each day of the week.
Wake-up
Leave home
Back home
Night
Program Y
our Schedule
Programs MO TU WE TH FR SA SU
6:00 6: 00 6:00 6:00 6:00 6:00 6:00
8:30 8: 30 8:30 8:30 8:30 --:-- --:- -
16:00 16:00 16:00 16:00 16:00 --:-- --:- -
23:00 23:00 23:00 23:00 23:00 23:00 23:00
Temperature Control
HandyHeat 132 thermostat works differently than conven-
tional electromechanical thermostats.
It is equipped with a proportional integral adaptive (PIA)
controller which determines heating cycles by analyzing
the temperature behavior history within the room.
The PIA controller reduces temperature swings providing
accurate temperature control while increasing user comfort.
The controller determines the amount of power required by
the heating system to maintain the setpoint temperature.
When the heating system is activated, one of the following
icons is displayed:
Technical Specifications
Model : HandyHeat 132 A/AF/F
Display range : 0°C to 60°C
Setting range (ambient) : 5°C to 30°C
Setting range (floor) : 5°C to 40°C
Pre-programmed temperature setpoints:
Comfort: A/AF 20°C and 28°C
Economy: A/AF 18°C and 20°C
Vacation: A/F/AF 10°C
Floor limit: AF 28°C
Temperature resolution display scale : 0.1°
Storage : -4°F to 120°F (-20°C to 50°C)
Software : Class A
Controller : Electronic
Temperature control : Proportional integral adaptive,
15-minute heating cycles.
Programming protection : Protected memory
Clock protection : 2 hours
Size (H/W/D) : 3.3 x 3.1 x 0.5 in (83 x 79 x13 mm)
Warranty
HandyHeat TWO YEAR LIMITED WARRANTY
This product is guaranteed against workship defects for
a two-year period following the initial date of purchase.
During this period HandyHeat will repair or replace, at
our option and without charge, any defective product
which has been used under normal conditions.
The warranty does not cover delivery costs and does not
apply to products poorly installed or randomly damaged
following installations.
This warranty cancels and replaces any other manufactu-
rer’s express or implied warranty as well as any other com-
pany commitment. HandyHeat cannot be held liable for
related or random damages following the installation of
this product.
The defective product as well as the purchase invoice must
be returned to the place of purchase or mailed, prepaid
and insured, to the nearest shipping address.
If you have any questions concerning the programming of
HandyHeat 132 programmable thermostat, contact our
technical support at:
1 to 20% 21 to 40% 41 to 6 0% 61 to 80% 81 to 100 %
Lundagervej 102
DK-8722 Hedensted
Denmark
Tel. [phone]
Fax [phone]
Email: [email protected]
www.handyheat.net
DVK-00079-001

-
Material
One (1) PB130-230 power base
One (1) floor sensor (for floor heating modules AF & F)
One (1) wall plate (optional, in certain countries)
Power Base
PB130-230
Installation Instructions
Technical Specifications
Model: PB130-230
Supply: 230 VAC, 50 Hz
Load: 16 A maximum (resistive only)
Power:3680 Watt (NI), 230 VAC
Certification:EN60730-2-9 / EN50081-1 / EN3082-2
Storage:-20°C to 50°C
Protection:Class 2
Protection degree:IP20
Automatic action:Type 1.B
Environment: Normally polluted
Size (H•W •D) : 75 x 75 x 14 mm (7.5 x 7.5 x 1.4 cm)
NOTE: The terminals are designed to handle
a wire size between 0.33 to 3.1 mm2
TWO(2) YEAR LIMITED WARRANTY
This product is guaranteed against workmanship defects for a two-year period
following the initial date of purchase. During this period HandyHeat will repair
or replace, at our option and without charge, any defective product which has
been used under normal conditions.
The warranty does not cover delivery costs and does not apply to products
poorly installed or randomly damaged following installation. This warranty
cancels and replaces any other manufacture’s express or implied warranty
as well as any other company commitment.
HandyHeat cannot be held liable for related or random damaged following
the installation of this product. The defective product as well as the purchase
invoice must be returned to the place of purchase or mailed, prepaid and in-
sured, to the nearest location.
If you have any questions concerning the installa-
tion of the PB130-230 power base, contact our
technical support team at :
Introduction
The PB 130-230 power base is designed to power a
HandyHeat 13x series control module. The resistive
load must not exceed 3680 watts (NI) 230 VAC (16A).
Installation Guidelines
Turn off power to the heating system at the mail power
panel to avoid electrical shock. Installation should be
carried out by an electrician.
All work must be conform to the most recent country’s
regulations for electrical installations and wiring.
This thermostat should be connected on a circuit equip-
ped with a fuse or a circuit breaker. It must be installed
on a certified electrical box.
For a new installation choose a location abput 1.5 m
(5 ft.) above the floor.
The thermostat must be installed facing the heating
system and on the inside wall.
Avoid locations where there are air drafts (top of stair-
case, air outlet), dead air spots (behind a door), direct
sunlight or concealed chimneys or stove pipes.
Remove the screw holding the
control module to the power
base.
Note that the screw cannot be
completely removed.
If you have a wall plate:
Before making the connections, make
sure that the base covers the electrical
box entirely. If not, insert the cover
plate on rear of the base.
NOTE:The cover plate can be used to cover
the plate for aesthetics.
Connect the wires:
•Power:
Terminals 1 and 5
•Load:
Terminals 2 and 4
•Floor sensor:
Terminals 6 and 7
(no polarity needs
to be respected)
Do not place the floor sen-
sor directly next to an ele-
ment but rather for maximum performance, the floor
sensor should be centred between the wires in the
mat (80°C max.). The temperature sensor wire can-
not lay across any heater wires.
If the load is driven through
a contractor, a snubber must
be installed at the contrac-
tor’s coil terminal. See wiring
diagram below.
Push wires into the electrical box and
secure the base to the electrical box
anchorage. The head of the screw
must be less than 2 mm thick.
Conigure the switches ( if necessa-
ry) and istall the control module
onto the power base (refer to
the user guide).
Return power to the heating system.
DVK-00086-001
Installation and Wiring
Lundagervej 102
DK-8722 Hedensted
Denmark
Tel. [phone]
Fax [phone]
Email: [email protected]
www.handyheat.net
Product of Denmark