Hansol H530 User manual

Printed in Korea
Part No. 942255020001-01
www.hansolel.co.kr
TFT-LCD Color Monitor
USER'S MANUAL
15
Printed on the recyclable paper

Parts 3
Connection to Computer 4
The range of control Angle 5
Installing Monitor Driver 6
Name and Function of Front 8
Power Management Feature 10
Adjusting OSD 11
Standard Signal Table 17
Specification 18
Troubleshooting 19
Warning 21
Table of Contents
INFORMATION TO USER :
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.This equipment generates, uses and can
radiate radio frequency energy and,if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation; if this equipment does cause harmful interference to radio or
television reception, which can be determined by determined by turning the
equipment off and on, the user is encouraged to try to crrent the interference by
one or more of the fllowing measures:
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit difference
from that to which the recerver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cable has to be used to ensure product compliance.
CAUTION : Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment

32
Parts
LCD Monitor
Place the monitor to face the user and then adjust the monitor angle.
Take a break (for about 10 minutes) at every hour during the work with monitor.
Refer to the following figure to take the correct posture.
about 50cm
Look down the monitor
below the horizon.
Relax shoulders and arms,
and sit back on the chair.
Adjust the monitor to
prevent reflection.
Adjust the monitor stand
to acquire required angle.
Keep feet flat on the ground.
Maintain the arms horizontally
and place hands softly on
the keyboard.
Good Posture Guide
12V-DC Adapter
User's Manual /
Warranty Card
Signal Cable AC Power Cable
Installation Disk
Installation Diskette
For use only with
power supply
M
ANUFACTURER
: AcBel
MODEL : API-208-98010

5
T he range of control Angle
How to Adjust the Stand
4
Connection to Computer
1. Use 220 V or 110 V. (Free Voltage)
2. Connect monitor and computer via computer cable (See figure )
3. Power on the monitor and computer.
4. Connection is finished.
12V DC connection
terminal Computer cable
For PC
For Macintosh
Use adapter.
Adapter for Macintosh (Optional)
Refer to the table on the rear side of
the optional Macintosh adapter and
adjust DIP switch by the resolution.
Forward 4
Default
Backward 18
Basic Connection

76
Click 'Finish'.
Click 'Next>'.
Click 'Advanced..'. Click 'Next>'.
Click 'Monitor'. Click 'Change..'.
Click 'Display a list of all...'.
Click 'Next>'.
Click 'Have Disk..'.
Select the driver and click 'OK'. Click 'Next>'.
3. Select "Exit" if the monitor model is changed, and then reboot the Windows.
Installing Monitor Driver
1. Insert the Diskette to the Floppy Diskette driver.
2. Double-click "Install.exe".
3. Select the model(H530) and click "OK" button.
4. Select inf file, and then click "OK" button.
5. Click "Exit" button to close the installation.
Automatic Installation
Manual Installation
1. Insert the Diskette to the Floppy Diskette driver.
2. Click 'My Computer' and follow the procedure below.
Click 'Control Panel'. Click 'Display'. Click 'Settings'.
Run (Click) "Install" at Floppy driver and select the model name to set the
optimum display in Window 95, 98 or 2000.
Use the Driver provided.

98
Power button
Power button is located in the lower center of the Front Bezel.
You can push the button to turn on/off the power.
Power Indicating LED
If the green LED around the power switch turns into blinking amber,
it indicates the monitor is in power saving mode.
On Screen Display (OSD) Function Button
OSD buttons on the front of bezel perform the following functions.
MENU : Press this button to display menus.
SELECT/ AUTO : Press this button, when OSD is not displayed, to perform
automatic setting.
When OSD is displayed, You can select icons.
POWER : Power button.
: By pressing these button when OSD is displayed, You can move cursor into
the menus which you want.
After press the SELECT button, you can change gauge level or
select sub menus.
Name and Function of Front
Front panel Functions
SELECT/ AUTO BUTTON
MENU BUTTON
+ BUTTON
- BUTTON
POWER BUTTON

11
Horizontal Position
79%
Brightness
CLK
AUTO
PH
EXIT
Adjusting OSD
Brightness
Contrast
51%
Contrast
CLK
AUTO
PH
EXIT
49%
H-Position
CLK
AUTO
PH
EXIT
MENU
1. Press the Menu button.
2. Use to move Brightness ICON.
3. Use SELECT button to select it.
4. Use to adjust the brightness.
SELECT
MENU SELECT
MENU SELECT
1. Press the Menu button.
2. Use to move Contrast ICON.
3. Use SELECT button to select it.
4. Use to adjust the contrast.
1. Press the Menu button.
2. Use to move H-Position ICON.
3. Use SELECT button to select it.
4. Use to adjust display left or right.
10
No image is displayed with Amber blinking.
Monitor is in power saving mode.
Use mouse or keyboard to release power saving mode.
No image is displayed without LED on.
Power cable plug must be pulled out.
Check the power plug on monitor and on the wall.
"Out of range" displayed on the screen.
This message is displayed when the signal from video card exceeds the
maximum frequency of the monitor. Readjust resolution and frequency in
accordance with the monitor capacity. (Refer to Standard Signal Table)
Power Management Feature
When not in use for a long time, the monitor
automatically reduces its power consumption, meeting power saving
standards of EPA and NUTEK.
The monitor is equipped with a power saving circuit that
confirms to the world-standard Display Power Manager Signalling
(DPMS) mode of Video Electronics Standard Association (VESA).
The power management feature requires that the video card of the
computer should support DPMS function.
Status Color of LED Power Consumption
Normal Green Normal Power
DPMS mode Amber Blinking
( 2 second interval ) 5 W or Below

Clock Phase
User Color
1312
Adjust : +,-
Color
CLK
AUTO
PH
EXIT
9300K
Color
USER USER USER
96%
Color
USER USER USER
1. Press the Menu button.
2. Use to move Color ICON.
3. Use SELECT button to select it.
4. Use into the submenu.
1. Use to move Red, Green, Blue ICON.
2. Use SELECT button to select color what
you want.
3. Use to increase or decrease each color.
4. Press the Menu button to exit.
1. Use to select the I or II.
2. Press the Menu button to exit.
I:Bluish white II : Reddish white
Clock Phase
51%
V-Position
CLK
AUTO
PH
EXIT
50%
Clock
CLK
AUTO
PH
EXIT
64%
Clock Phase
CLK
AUTO
PH
EXIT
1. Press the Menu button.
2. Use to move V-Position ICON.
3. Use SELECT button to select it.
4. Use to adjust display upward or downward.
1. Press the Menu button.
2. Use to move Clock Phase ICON.
3. Use SELECT button to select it.
4. Use to correct fine trembling or Video noise.
1. Press the Menu button.
2. Use to move Clock ICON.
3. Use SELECT button to select it.
4. If Auto-cnfig function fails to remove Video noise,
Use or to remove vertical noise.
( Adjusting clock phase is required after the
adjustment of clock.)
MENU SELECT
MENU SELECT
MENU SELECT
MENU
MENU SELECT
MENU
SELECT
Vertical Position
Clock
Clock Phase
Color
Preset Color

1514
58%
OSD
Sharpness
OSD
100% 50%
OSD Overlay
Language
English
CLK
AUTO
PH
EXIT
1. Use to move OSD Overlay ICON.
2. Use SELECT button to select it.
3. Use to adjust OSD Overlay.
4. Press Menu button to exit.
1. Use to move Sharpness ICON.
2. Use SELECT button to select it.
3. Use to adjust Sharpness.
4. Press Menu button to exit.
1. Press the Menu button.
2. Use to move Language ICON.
3. Use SELECT button to select it.
4. Use to select language in order.
Adjust : +,-
SPECIAL
CLK
AUTO
PH
EXIT
OSD
0.7V 1.0V
Video Level
OSD
640M 720M
DOS Mode
1. Press the Menu button.
2. Use to move SPECIAL ICON.
3. Use SELECT button to select it.
4. Use into the submenu.
1. Use to move SPECIAL ICON.
2. Use SELECT button to select it.
3. Use to adjust level.
4. Press the Menu button to exit.
1. Use to move DOS Mode ICON.
2. Use SELECT button to select it.
3. Use to select DOS Mode what you want.
4. Press Menu button to exit.
MENU SELECT
MENU SELECT
MENU
SELECT
MENU
SELECT
MENU
SELECT
MENU
SELECT
LanguageDOS Mode
SharpnessSharpnessSharpnessVidio Level
OSD OverlayOSD OverlayOSD OverlaySpecial

17
Standard Signal Table
Pin assignment table D-Sub
Mini 15pin connector
VGA (720 X 400)
VGA (640 X 480)
VGA (640 X 480)
SVGA (800 X 600)
XGA (1024 X 768)
XGA (1024 X 768)
MAC (640 X 480)
MAC (832 X 624)
31.469
31.469
37.500
46.875
48.363
60.023
35.000
49.726
70.087
59.940
75.000
75.000
60.004
75.029
66.667
74.551
28.322
25.175
31.500
49.500
65.000
78.750
30.240
57.284
Resolution
Horizontal Frequency
(KHz)
Vertical Frequency
(Hz) Clock Frequency
(MHz)
15
11 15
610
15pin D-Sub
Pin No. Assignment Pin No. Assignment
1 Red Video 9 N.C
2 Green Video 10 Ground
3 Blue Video 11 Ground
4 N.C 12 SDA
5 Ground 13 H.Sync
6 Red Video Ground 14 V.Sync
7 Green Video Ground 15 SCL
8 Blue Video Ground
16
CLK
AUTO
PH
Information
60.0 KHz / 75.0 Hz
Auto - Config
Start : + , -
CLK
AUTO
PH
EXIT
Auto-Config
Wait a Moment
1. Press the Menu button.
2. Use to move the Auto-config ICON.
You can know a display information
(Horizontal, Vertical Frequency)
1. Press the Menu button.
2. Use to move the Auto-config ICON.
3. Use SELECT button to select it.
4. Use or to readjust the display condition.
In most case, Auto-Config adjusts display
appropriately. Use PH or adjust CLK
in accordance with graphic card to fine tune
the display.
MENU SELECT
MENU
MENU SELECT
CLK
AUTO
PH
Menu Exit
Select
1. Press the Menu button.
2. Use to move the Exit ICON.
3. Press SELECT button to exit.
Auto-ConfigAuto-Config
Auto-ConfigInformation
Auto-ConfigMenu Exit