Hanwha Techwin SBP-300NB User manual

SBP-300NB (IVORY)
SBP-300NBW (WHITE)
INSTALLATION BOX
User Manual

overview
CONTENTS
OVERVIEW
3
INSTALLATION & CONNECTION
6
APPENDIX
12
Copyright
©2019 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered.The name of this product and other trademarks mentioned in this manual are the registered trademark of their
respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin reserves the
right to change the contents of this document without prior notice.
Design and specications are subject to change without prior notice.
INSTALLATION BOX
User Manual

English _3
overview
CONTENTS
OVERVIEW
3
4What’s Included
INSTALLATION & CONNECTION
6
6Installation
APPENDIX
12
12 Specification
12 Product Overview

overview
4_ overview
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Appearance Item Name Quantity
INSTALLATION BOX 1
INSTALL BRACKET 1
Gasket (for SBP-300WM1/WMW1) 1
Gasket (for SBP-300WM/WMW) 1
RUBBER HOUSING 1
BRACKET ADAPTOR 1
Appearance Item Name Quantity
MOUNT CAP 5
MOUNT CAP fastener 1
M10 x L22 screw (to attach the install bracket) 4
M8 x L20 screw (to attach the housing) 4
M3 x L6 screw
(to attach the bracket adaptor and media convert) 4
M10 x L12 wrench bolt (to attach SBP-300WM/WMW) 4
M10 x L20 wrench bolt (to attach SBP-300WM1/WMW1) 4
M4 x L8 screw (to attach the media convert) 2

English _5
overview
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Appearance Item Name Quantity
INSTALLATION BOX 1
INSTALL BRACKET 1
Gasket (for SBP-300WM1/WMW1) 1
Gasket (for SBP-300WM/WMW) 1
RUBBER HOUSING 1
BRACKET ADAPTOR 1
Appearance Item Name Quantity
MOUNT CAP 5
MOUNT CAP fastener 1
M10 x L22 screw (to attach the install bracket) 4
M8 x L20 screw (to attach the housing) 4
M3 x L6 screw
(to attach the bracket adaptor and media convert) 4
M10 x L12 wrench bolt (to attach SBP-300WM/WMW) 4
M10 x L20 wrench bolt (to attach SBP-300WM1/WMW1) 4
M4 x L8 screw (to attach the media convert) 2

6_ installation & connection
installation & connection
INSTALLATION
1. Push the locking lever on the door to separate the housing and door.
2. Undo the four screws to separate the bracket adaptor.
Lock the unused piping hole with the attached mount cap.
Use a mount cap fastener to attach the mount cap.
BRACKET
ADAPTOR
Mount cap
fastener Mount cap
3. Remove the double-sided tap on the rear side of the gasket and affix it to the door.
Attach the wall mount to the door using the four M10 screws.
< Tighten each of the four screws a little at a time so that the wall mount is evenly pressed
to the gasket. >
DOOR
HOUSING
LOCKING
LEVER
LOCKING LEVER

English _7
installation & connection
INSTALLATION
1. Push the locking lever on the door to separate the housing and door.
2. Undo the four screws to separate the bracket adaptor.
Lock the unused piping hole with the attached mount cap.
Use a mount cap fastener to attach the mount cap.
3. Remove the double-sided tap on the rear side of the gasket and affix it to the door.
Attach the wall mount to the door using the four M10 screws.
< Tighten each of the four screws a little at a time so that the wall mount is evenly pressed
to the gasket. >
•Use of SBP-300WM1/SBP-300WMW1 wall mount (with M10 x L20 screws)
DOOR GASKET
HOUSING
•Use of SBP-300WM/SBP-300WMW wall mount (evenly securing the wall mount
inside the gasket groove as shown in the image below.) (with M10 x L12 screws)
DOOR
GASKET
GASKET
JPlease assemble
the set in such a
way that the lock tab
faces down into the
slot in the installation
direction.

installation & connection
8_ installation & connection
4. Attach the install bracket to the wall, corner mount (SBP-300KM/SBP-300KMW) or pole mount
(SBP-300PM/SBP-300PMW) using the M10 screws.
Only use the 4 screws included in the accessories as shown in the image below.
Screw (circular head, with M10 x L22 screw)
•Installation on the wall
•Pole Mount
•Corner Mount
5. Place the housing on the install bracket as shown in the image.
`To install it on the wall, attach the rubber housing as shown in the figure.
The rubber is not waterproof. It is decorative only, serving to hide a gap.
Therefore, if the cable is inserted into the main body separately and not through the duct on the wall, the insertion
point of the cable must be completely waterproof.
If this is not done, any water leaks may cause problems.
6. Secure the housing to the install bracket using 4 M8 screws in the same ways as "No. 4" in the
installation procedure.

English _9
installation & connection
4. Attach the install bracket to the wall, corner mount (SBP-300KM/SBP-300KMW) or pole mount
(SBP-300PM/SBP-300PMW) using the M10 screws.
Only use the 4 screws included in the accessories as shown in the image below.
5. Place the housing on the install bracket as shown in the image.
`To install it on the wall, attach the rubber housing as shown in the figure.
The rubber is not waterproof. It is decorative only, serving to hide a gap.
Therefore, if the cable is inserted into the main body separately and not through the duct on the wall, the insertion
point of the cable must be completely waterproof.
If this is not done, any water leaks may cause problems.
6. Secure the housing to the install bracket using 4 M8 screws in the same ways as "No. 4" in the
installation procedure.
Cable
Waterproofing
needed

installation & connection
10_ installation & connection
7. Insert the external cable into the main body using a pipe.
Wrap the thread of the pipe screw with Teflon tape to protect against water leakage problems.
(Make sure that water leaks will not cause a problem at the cable insertion point.)
8.
Install the power adaptor and media converter using the bracket adaptor, and connect the external cable.
CABLE
Teflon tape
Power
adaptor
BRACKET ADAPTOR
MEDIA CONVERTER
9. Pull the cable out through the door and wall mount and mount the door on the housing.
(Return the locking lever to its original position and check that the hinge is properly attached to the
housing.)
10. Fasten the door to the housing using a hexagonal wrench. (Tighten the screws while pressing the
door with your hand as shown in the image below. Then tighten each of the screws a little at a
time to make sure that the door is tightly pressed to the housing.)

English _11
installation & connection
7. Insert the external cable into the main body using a pipe.
Wrap the thread of the pipe screw with Teflon tape to protect against water leakage problems.
(Make sure that water leaks will not cause a problem at the cable insertion point.)
8. Install the power adaptor and media convert using the bracket adaptor, and connect the external
cable.
9. Pull the cable out through the door and wall mount and mount the door on the housing.
(Return the locking lever to its original position and check that the hinge is properly attached to the
housing.)
10. Fasten the door to the housing using a hexagonal wrench. (Tighten the screws while pressing the
door with your hand as shown in the image below. Then tighten each of the screws a little at a
time to make sure that the door is tightly pressed to the housing.)
Wall Mount
Cable
DOOR
HOUSING
LOCKING LEVER
LOCKING LEVER

12_ appendix
appendix
SPECIFICATION
Items Description
Dimensions (mm) W185.0 x D221.0 x H94.3 (mm)
Weight 3.4kg
Material STEEL, ALUMINUM, SILICON
PRODUCT OVERVIEW
Unit : mm (inch)
MEMO

PT01-004102A
Head Oce
6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : [phone] Fax : [phone]
www.hanwha-security.com
Hanwha Techwin America
500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Toll Free +1.877.213.1222 Direct +1.201.325.6920
Fax [phone]
www.hanwhasecurity.com
Hanwha Techwin Europe
Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom
Tel [phone] Fax [phone]
www.hanwha-security.eu