Vivo STAND-V006 User manual

Hex Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v006
SKU: STAND-V006
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
a (x1)
Pole
b1 (x1)
Clamp
b2 (x1)
Clamp
Brace
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
c(x1)
Decorative
Cover
d1 (x2)
Monitor Arm
d2 (x4)
Monitor Arm
e (x8)
Monitor Arm
Cover
f (x8)
Plastic Pad
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
g (x4)
M10x47
h(x3)
Clamp Brace Bolt
i(x2)
M10x15
j (x4)
M8x10
k (x1)
M10 Bolt
l (x1)
Support Plate
m(x1)
M10 Washer
o(x1)
Eva Pad
p (x24)
M4x12 Thumb Screw
r (x24)
M4 Spacer
s (x2)
Spare Cap
t(x1)
Allen Wrench
Set
u(x1)
Wrench
v1 (x4)
VESA Plate
v2 (x2)
VESA Plate
w1 (x4)
Nut
w2 (x2)
M4x6
x(x8)
Wire Clip
n(x1)
Spring Washer
q (x24)
M4x30

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
STEP 1
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
a
h
b2
Figure 1 Figure 2
t
i
b1 eye bolt
c
Figure 3 Figure 4
o
a
c
a
l
k
m
n
OPTION A: Weighted Base Installation
Attach clamp brace (b2) to pole (a) with clamp brace bolts (h). Attach clamp (b1) to clamp brace at
desired height using M10x15 bolts (i) with Allen wrench (t). Tighten clamp to desk and slide decorative
cover (c) into place.
OPTION B: Existing Grommet Base Installation
Apply foam pad (o) to base of pole (a). Mount pole to grommet hole in desk using M10 bolt (k), spring
washer (n), M10 washer (m) and support plate (l). Tighten with wrench (u) and slide decorative cover
(c) into place.

4
STEP 2
STEP 1 (Continued)
Figure 5 Figure 6
o
a
c
a
l
k
m
n
2.1
d2
d2
d1
e
e
g
t
f
2.2
2.3
Step 4B
OPTION C: Self-Drilled Grommet Base Installation
Drill a 3/8” (10mm) diameter hole at desired location. Apply foam pad (o) to base of pole (a). Mount
pole to grommet hole in desk using M10 bolt (k), spring washer (n), M10 washer (m) and support
plate (l). Tighten with wrench (u) and slide decorative cover (c) into place.
Place plastic pads (f) onto ends of monitor arms (d2), insert into arms (d1), and secure using M10x47
bolts (g) with Allen wrench (t). Press monitor arm covers (e) onto joints.

5
STEP 3
t
a
j
d1,d2
x
STEP 4
p
v1
r
q
v1
p
v2
r
q
v2
Install wire clips (x) on arms (d1,d2). Install arms on pole (a) at
desired height using M8x10 bolts (j) with Allen wrench (t), making sure
wire clips are facing down.
4A: Side VESA Plates
For monitors with flat back attach VESA plates (v1) with thumb screws (p). For monitors with curved
back attach VESA plates (v1) with screws (q) and spacers (r). Screws need only to be finger-tight.
4B: Center VESA Plates
For monitors with flat back attach VESA plates (v2) with thumb screws (p). For monitors with curved
back attach VESA plates (v2) with screws (q) and spacers (r). Screws need only to be finger-tight.

6
STEP 5
STEP 6
d1,d2
d1,d2
w2
w1
t
grub
screw
Fix the tilt angle
u
5B: Center VESA Plates
Slide monitor onto the head of arm (d2) as shown in the diagram. Secure with screw (w2). Slide top
monitor onto mount in same fashion.
5A: Side VESA Plates
Slide monitor onto the head of arm (d2) as shown in the diagram. Secure with nut (w1).
Remove plastic cover and use wrench (u) to tighten the nut if the tilt angle cannot be fixed. Fasten the
grub screws on the center monitors to fix the tilt angle using Allen wrench (t).

7
STEP 8
STEP 7
STEP 9
t
t
Adjust the height of Center Monitors: Turn the bolt counter-clockwise to lower the center monitors.
Turn the bolt clockwise to raise the center monitors. Use allen wrench (t). Adjust the height of the
Side Monitors: Remove nut (w1) and turn the bolt counter-clockwise to raise the monitor. Use allen
wrench (t).
To adjust swivel joint tension, remove the monitor arm cover (e) and turn the bolt underneath with
the Allen wrench(t).
Use wire clips (x) to help manage wires.

LAST UPDATED: 07/09/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303