Happy Frizz ZERO User manual

www.happyfrizz.it/zero
USE AND MAINTENANCE MANUAL
FILTER, SODA MAKER AND REFRIGERATING SYSTEM
FOR WATER - HAPPY FRIZZ ZERO

3
TABLE OF CONTENTS
DECLARATION OF CONFORMITY ..................................................................... p. 3
MANUFACTURER’S DATA AND AUTHORISED ASSISTANCE............................. p. 4
IMPORTANT PRECAUTIONS............................................................................. p. 5
PACK CONTENTS ............................................................................................. p. 9
ZERO SYSTEM OVERVIEW............................................................................... p. 10
INSTALLATION OF A CO2CYLINDER ................................................................ p. 12
FIRST START-UP PROCEDURE......................................................................... p. 13
HOW TO USE HAPPY FRIZZ ZERO ................................................................... p. 17
O-RING SEALS ..............................................................................................p. 20
KIT FOR SANITISATION/DECALCIFICATION AND FILTER CHANGE .................. p. 21
SANITISATION/DECALCIFICATION PROCEDURE/FILTER CHANGE................... p. 22
CARBONATION LEVELS AND FIZZY DRINKS PREPARATION ........................... p. 30
MAINTENANCE p. 32
CYLINDER REPLACEMENT .............................................................................. p. 33
RESOLUTION OF PROBLEM ............................................................................. p. 34
ASSISTANCE .............................................................................................. p. 35
REGULATIONS .............................................................................................. p. 36
WARRANTY .............................................................................................. p. 37
DECLARATION OF CONFORMITY
GENERAL DESCRIPTION AND TECHNICAL DATA
The product described in this document is a device for dispensing ltered water, at room temperature or
cooled. The water supplied can be carbonated.
The appliance was made with components whose materials comply with the requirements of Regulation
1935/2004 which establishes the general principles of safety and inertia for all MOCAs (materials and
objects in contact with food), of Reg. (CE) 282/2008 relating to recycled plastic materials and objects
intended for contact with food, of Reg. (CE) 10/2011 concerning plastic materials and objects intended to
come into contact with food products, Reg. (EC) 450/2009 concerning active and smart materials intended
to come into contact with food.
The system was built in accordance with good manufacturing practices (Reg. (CE) no.2023/2006)
so that, under normal or foreseeable conditions of use, it does not transfer components to food products in
quantities such as to:
a) constitute a danger to human health;
b) result in an unacceptable change in the composition of food products;
c) lead to a deterioration of their organoleptic characteristics.
Machine dimensions
Width: 210mm
Depth: 420 mm
height: 440 mm
Weight: 9 kg unladen
Power supply
Voltage: 220-240 V A.C.
Frequency: 50-60 Hz
Power: max 80 W
Identication plates
On HAPPY FRIZZ ZERO an identication plate is applied on which are reported identiers and the main
technical data relating to weights and power supplies.
The feasible operations are those indicated in this manual in the INTENDED USE section.
Everything that is not feasible, as well as partial or total non-compliance with the procedures described in
the manuals, can be the cause not only of errors in the work phase, but also of accidents such as to cause
serious damage to the machine and to its operators.
send an e-mail to st[email protected]
and request FREE OF CHARGE
the instructions in simplied on-screen
format or use the QR codes indicated below
and view them with your smartphone!
On-screen rst activation
procedure instructions On-screen procedure instructions sanitisation/
decalcication and lter
change
On-screen normal use
instructions
NOTE: THE MANUFACTURER CANNOT IN ANY CASE BE CONSIDERED RESPONSIBLE FOR INCIDENTS OR
DAMAGE ARISING FROM THE UNINTENDED AND UNAUTHORISED USES OF HAPPY FRIZZ ZERO.

4 5
HAPPY FRIZZ ZERO SODA MAKER FRIDGE FILTER
Dear customer, we thank you for your trust in us and welcome you to the HAPPY FRIZZ family.
You are entering the new ERA of the domestic beverage and we hope that our domestic dispenser is the
product that makes you say “never again without”.
A SMALL NOTE FROM OUR STAFF
ZERO is something new. There is no Home Drink Dispenser anywhere in the world designed exclusively for
the home.
In general, the market sells to families products intended for other sales channels, which do not take modern
day life into consideration.
We are sure that you have chosen us because you were not looking for a product with the obligation of
installation, with high maintenance costs, one that is cumbersome and without a doubt you didn’t want the
presence of a technician at home for every lter change.
This is why we have created a product tailored for you.
For any information or requirement, please visit our website or contact us. Our after-sales assistants will
resolve any of your needs.
Goodbye for now.
SAFETY INFORMATION AND WARNINGS
SAVE THESE INSTRUCTIONS AND PASS THEM ON TO THE USERS WHO WILL BE USING THE APPLIANCE.
Before using the HAPPY FRIZZ ZERO system, read and understand the use and maintenance instructions
and the safety information.
MANUFACTURER’S DATA
COMPANY NAME Biotech Trentino SpA
COMPANY HEADQUARTERS Via Innsbruck 22- 38121 Trento
VAT NO. 02009940228
TEL. OFFICE +39 0461.1725792
E-MAIL [email protected]
WEBSITE www.hapyfrizz.it
AUTHORISED ASSISTANCE
Maintenance and technical assistance on the machine can only be performed by the manufacturer or by a
technician appointed by the same.
IMPORTANT PRECAUTIONS - READ BEFORE USE
HAPPY FRIZZ ZERO
▶DANGER! Modication of the control system is prohibited. Biotech Trentino S.p.A. assumes no liability
for inappropriate and unauthorised use of the machine following tampering and negligence of an
operator. Anyone who has to perform any operation with the machine must be familiar with the
meaning and use of the Happy Frizz ZERO system.
▶ATTENTION: The efciency of the control devices is guaranteed subject to the use of the machine
appropriately as described in this manual; in particular the maintenance operations described in the
maintenance section must be strictly carried out and must not be modied.
As it would be impossible to describe all the operations that must not or cannot be performed, it is
believed that all the operations (different from the normal ones) that are not explicitly described in the
documentation of the machine, are to be considered not feasible.
The feasible operations are those indicated in this manual.
Everything that is not feasible, as well as the partial or total non-observance of the procedures
described in the manual, can be the cause not only of errors during work, but also of accidents that can
cause serious damage to the machine and to its users.
NOTE: The manufacturer cannot be held responsible in any case for accidents or consequential damage
due to unanticipated and unauthorised use of HAPPY FRIZZ ZERO.
NOTA: La ditta produttrice non può essere ritenuta in alcun caso responsabile di incidenti o danni conseguenti
ad usi non previsti e non autorizzati di HAPPY FRIZZ ZERO.
MACHINE INTENDED AND UNINTENDED USE
Intended use
HAPPY FRIZZ ZERO has been designed and built only and exclusively as a machine for private use to cool,
microlter and dispense water, with the possibility of carbonating it using carbon dioxide.
Unintended use
No uses other than those described in the INTENDED USE paragraph is envisaged. The following are also prohibited:
→The use of HAPPY FRIZZ ZERO or parts of it for uses other than those envisaged
→Replacement of parts and components of the machine with others not recognised by Biotech Trentino S.p.A.
→Tampering with/modifying the machine
→Exceeding the maximum tolerated pressures
→The use of accessories not recognised by Biotech Trentino S.p.A.
→The use of cylinders that are not supported by the HAPPY FRIZZ ZERO system
→Carbonating with substances other than water
. The reuse of any part of the machine after it has been taken out of service exempts the manufacturer from
any liability arising from its use.
BOTTLES:
▶WARNING: IF A BOTTLE IS USED FOR CARBONATION ON WHICH THE THE SYMBOL
“DISHWASHABLE” IS NOT PRESENT, DO NOT WASH IT IN A DISHWASHER AND DO NOT EXPOSE IT
TO VERY HOT OR VERY COLD TEMPERATURES..
▶WARNING: DO NOT carbonate using bottles that are not suitable for use with the ZERO system.
▶WARNING: Only use HAPPPY FRIZZ bottles. The use of bottles of other brands compromises the
functionality of the device invalidating the warranty of the product.
GENERAL WARNINGS:
▶DANGER: improper use of the ZERO system can cause serious injury to persons.
▶WARNING: DO NOT perform the carbonation in an empty or partially empty bottle.
▶Prima di utilizzare il sistema ZERO per gasare l’acqua, posizionare correttamente la bottiglia per la
gasatura.
▶DO NOT move the ZERO system during carbonation.
▶DO NOT remove the bottle during carbonation.

6 7
PLACE OF INSTALLATION
▶WARNING: Do NOT use the ZERO system unless it is in a vertical position.
▶DANGER: use the ZERO system ONLY with tap water. Use of the ZERO system for purposes other than
those indicated may cause serious injury to persons and damage to the device.
▶WARNING: use the ZERO system on a flat, stable surface away from heat sources.
DO NOT place the ZERO system on very hot surfaces (for example, on the surface of an oven) and do not
use it near naked flames or in the vicinity of flammable solvents such as alcohol or thinners.
▶WARNING: Do not place the machine near flammable solvents such as alcohol or thinners.
▶WARNING: Do not install the machine in excessively humid or dusty places, exposed to direct sunlight,
outside or near heat sources.
▶WARNING: Installing the machine in these places could cause re or electric shock.
▶WARNING: The device is not suitable for use in open areas.
▶WARNING: If in the future you decide to connect the ZERO system to the water supply, all existing pipes,
seals and joints between the machine and the mains water outlet must be replaced with new materials
to avoid contaminations.
The ZERO installation kit is provided. Purchase the original HAPPY FRIZZ kit. Installation with non-
compliant materials and ttings invalidates the product warranty.
E’ previsto il kit di installazione ZERO. Acquista il kit originale HAPPY FRIZZ. L’installazione con materiali
e raccorderia non conforme, annulla la garanzia prodotto.
▶WARNING: To reduce the risk of damage to property or persons, service or repairs must be carried out
exclusively by an authorised service representative of HappyFrizz®.
▶WARNING: Do not pull the power cord to remove the plug from the socket.
▶WARNING: Before using the ZERO system, make sure the appliance is not resting on the power cord.
Failure to comply with any safety regulations could result in re, electric shock or damage to the machine.
POWER SUPPLY
▶WARNING: The connection to the electrical network takes place by connecting the plug to a mains socket. The
current socket must be equipped with an efcient earthing socket and must be sized for the appliance load.
▶ATTENTION: Before inserting the plug, check that the voltage and frequency values of the electrical power
supply correspond to those indicated in the technical specications of Happy Frizz ZERO.
Avoid being barefoot when connecting and disconnecting the plug.
▶WARNING: Do not place or disconnect the machine from the power outlet with wet hands.
▶WARNING: Insert the plug rmly into the wall socket.
▶WARNING: Do not damage, modify, stretch, bend or twist the power cord.
Do not place heavy objects on the power cord.
▶WARNING: Do not use the machine if the power cord is tied or has knots.
▶WARNING: If you notice smoke, unusual smells or strange noises coming from the machine,
immediately unplug the machine from the power outlet and contact the technical assistance servic
Using the machine in these conditions could cause re or electric shock.
▶WARNING: Periodically, unplug the machine from the power outlet and, with a dry cloth, clean the plug
and the socket. If the machine is connected to a place exposed to dust, smoke or high humidity, the
dust accumulated on the socket absorbs moisture and could alter the insulation and start a re.
▶WARNING: Do not spray water on the device, as this may cause electric shock or re.
▶AVVERTENZA: The machine must not be installed in areas where a water jet can be generated.
▶AVVERTENZA: Use a damp cloth to clean the machine. Do not use flammable solvents.
▶AVVERTENZA: Use a damp cloth to clean the machine. Do not use flammable solvents such as alcohol,
benzene, or thinners. If flammable substances come into contact with the electrical components inside
the machine they could cause re or electric shock.
▶AVVERTENZA: Before cleaning the machine, turn it off and unplug it from the power outlet. Failure to
turn off or accidental switching on during cleaning could result in personal injury or machine damage.
▶AVVERTENZA: The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or with insufcient experience or knowledge, unless they have
been supervised through the intermediation of a person responsible for their safety or have received
instructions concerning use of the appliance. Children must be supervised to ensure they do not play
with the appliance.
USE OF THE MACHINE
Safety and warnings
Should any unexpected anomaly occur after having powered HAPPY FRIZZ ZERO:
→Turn off the power by pulling the plug out of the socket.
→Close the water supply valve (if connected to the water supply).
→Check if this manual contains information that is sufcient and necessary to release it in complete
safety (see Residual Risks). Alternatively contact technical assistance immediately to receive precise
information.
IMPORTANT:
→Do not remove any panelling or grid.
→Do not place objects on the machine.
→Always lift the machine even for small movements; absolutely avoid pushing it or dragging it.
→Do not touch it with wet hands or feet.
→Do not use it when barefoot.
→Do not use extension cords in places subject to jets or splashes of water.
→Do not pull the power cord to disconnect it from the mains.
▶DANGER: ACCESS TO THE INTERNAL PARTS OF THE MACHINE MUST ONLY BE CARRIED OUT FOR
MAINTENANCE OPERATIONS AND ONLY BY AUTHORISED PERSONNEL WHO HAVEALREADY READ THE
MANUAL..
Before servicing the machine it is necessary to disconnect it from the mains.
IMPORTANT:
→Do not put your hands, or objects held with your hands inside the device.
→Do not wet the electrical connections and the internal components with water or other liquids.
→Maintenance operations must be performed solely and exclusively by following the instructions in the
manual.

8 9
CYLINDERS CO2
▶DANGER: the escape of CO2 can cause carbon dioxide poisoning. In case of leakage of CO2 , ventilate
the room, breathe in fresh air and, if symptoms persist, contact a doctor immediately.
▶WARNING: before use, inspect the cylinder to check for dents, holes or other damage. If any damage is
found, DO NOT use the cylinder and contact an authorised HappyFrizz® service technician.
▶WARNING: improper use of the cylinder can cause serious injury to persons.
▶WARNING: immediately after use, carefully remove the cylinder as it could be very cold.
▶WARNING: Keep the cylinder away from heat sources and away from direct sunlight.
▶WARNING: DO NOT transport the ZERO system with the cylinder in position.
▶WARNING: NEVER tamper with the cylinder in any way.
▶WARNING: NEVER puncture or burn the cylinder.
▶WARNING: Do NOT throw the cylinder or allow it to fall.
▶WARNING: Do NOT handle the cylinder while discharging CO2.
BOTTLES
▶WARNING: DO NOT carbonate using bottles that are not suitable for use with the ZERO system.
The soda maker and the ZERO HappyFrizz® system are designed to be used exclusively with HappyFrizz®
carbonating bottles.
▶DANGER: sif the “Dishwasher-safe” symbol is not clearly visible on the carbonating bottle”, DO NOT
WASH IN THE DISHWASHER OR EXPOSE THE BOTTLES TO TEMPERATURES OVER 49°C OR LESS
THAN 1°C. DO NOT rinse the bottle in hot water. Do not position the bottle near heat sources, for
example on the surface of an oven. Do not leave the bottle inside a car. Do NOT please the bottle in a
freezer. Otherwise the integrity of the carbonating bottle material could be compromised which could
cause serious injuries to persons and damage to the device.
▶WARNING: if anomalies are observed in the shape of the carbonating bottle, DO NOT use the bottle as it
is damaged. DO NOT use scratched, worn, discoloured or otherwise damaged carbonating bottles.
▶WARNING: on the HappyFrizz® carbonating bottles the expiry date is clearly indicated.
Do NOT use out of date bottles. Replace and recycle expired bottles according to the regulations of local
disposal.
→On rst use, rinse the carbonating bottles with cold or warm water.
→Sanitise the bottles with the HappyFrizz®. SEE SECTION “MAINTENANCE” on page 32.
CARBONATION
▶WARNING: USE THE CARBONATION FUNCTION EXCLUSIVELY
FOR THE CARBONATING OF NATURAL WATER. ADD CONCENTRATES ONLY AFTER CARBONATING.
▶WARNING: DO NOT perform the carbonation in an empty or partially empty bottle.
PACK CONTENTS:
→no. 1 REUSABLE CARBONATING BOTTLE1 L
→no. 1 CO2 CYLINDER (*)
→no. 1 ZERO SYSTEM complete with:
-1 POWER SUPPLY CABLE
- 1 FILTER (microltration 0.5 micron)
- 1 METAL DRIP TRAY
- 1 EXTERNAL TANK WITH LID
- 1 REUSABLE PRODUCT PROTECTION BAG
- The pack contains the ZERO HappyFrizz® system, one cylinder of CO2 supplied and a reusable carbonating bottle (without
bisphenol A) equipped with a cap that keeps the drink zzy.
- (*) It includes a full 425g cylinder. Once empty, it is possible to replace the empty cylinder with a full one at the cost of rell
only. With the supplied cylinder it is possible to produce up to 90 L of carbonated water, based on the level of carbonation
and the temperature of the water used.
D.I.C.SY PATENTED COOLING SYSTEM - THE HEART OF
HAPPY FRIZZ ZERO
This system is equipped with a patented technology called D.I.C.SY. - Direct Integrated Cooling System that
is able to cool water to 6 ÷ 30°C.
MICROFILTRATION
It is also equipped with a domestic water quick coupling lter with 0.5 micron sintered carbon block and 10
micron PP pre-lter that is able to remove tastes, unpleasant smells and any undesirable substances such as
chlorine and its derivatives, lead, mercury , asbestos, atrazine, benzene and protozoa cysts.
VELOCITA’ DI EROGAZIONE
DISPENSING SPEED
POWER SUPPLY
L x H x D
WEIGHT
TO TANK
COLD WATER
AMBIENT WATER
TO FIXED NETWORK
18 s 18 s
70 s
< 80 W/h
220 V AC - 50-60 Hz
210 mm x 420 mm x 440 mm
10 kg
60 s
Useful technical specications of the Happy Frizz ZERO system

10 11
ZERO SYSTEM OVERVIEW:
TOUCH
SCREEN
DRIP TRAY
WATER DISPENSER
CYLINDER
INSERTION DOOR
CUSTOM
CARBONATION KEY
EXTERNAL
WATER TANK (3L)
INTERNAL
WATER TANK (2,4L)
CARBONATION
NOZZLE
TANK LID
POWER SUPPLY
CABLE SOCKET
WATER NETWORK
COUPLING INPUT
MAX 1.2 BAR
OF PRESSURE
FILTER
HOUSING
Display, 5 keys/3 lights/2 temperature indicators:
NATURAL WATER
BUTTON
(blue, steady/flashing)
SANITISATION BUTTON
(magenta, steady/flashing)
COLD WATER
TEMPERATURE
REGULATION
BUTTONS
(blue, steady)
COLD WATER
BUTTON
(blue, steady/flashing)
TEMPERATURE
CURRENT COLD
WATER TEMPERATURE
WATER
TEMPERATURE
SET
EXTERNAL TANK
WATER LEVEL LIGHT
(red, steady or flashing)
FILTER LIGHT
(amber, flashing)
MAINTENANCE LIGHT
(red, steady or flashing).
If it comes on, read the
instructions on p. 5

12 13
USEFUL KEY:
PRESSURE
The term “key press” means the resting of a nger for more than 0.3 seconds on the desired icon. If the
time is less (for example during cleaning operations or drumming actions on the display by children, the
buttons do not activate, thereby avoiding accidental activations. This is also valid for exit from stand-by
(zone pressure active for at least 0.3s).
INSTALLATION OF THE CO2 CYLINDER
1. HOW TO OPEN THE CYLINDER COMPARTMENT::
Open the cylinder compartment of the ZERO system, making it slide
outwards. Grip it using the lower raised part on the front.
2. HOW TO INSTALL THE CO2 CYLINDER:
Remove the seal and the cap from the CO2 cylinder. Insert the CO2
cylinder in the dedicated compartment on the front of the ZERO
HappyFrizz® system and turn it clockwise by applying light pressure
until it is in position. To tighten, do so only manually: do not use
tools of any kind.
3: HOW TO CLOSE THE CYLINDER COMPARTMENT
Rest the lid on the compartment slide and push to the left following
the appropriate track.
SLITTA
FIRST ACTIVATION PROCEDURE :
IMPORTANT NOTES:
The rst activation however takes place in tank mode. ZERO performs an automatic check-up to verify the
functioning of all the internal components present. If the lter is not mounted, the rst activation cannot be
completed as the natural water bottle cannot be calibrated (emptying of the external tank during the rst
70 s).
Your ZERO system has in any case been tested by our experienced staff before being packed. All the ZERO
systems undergo stress tests and functional checks, which is why it is normal to nd a few drops of water in
the device (added to a sanitising substance). With the FIRST ACTIVATION procedure the sanitising residues
are expelled.
▶WARNING: During the rst lling phase gurgling sounds can be heard due to the presence of air inside
the hydraulic circuit. These normally disappear at the end of the rst activation
(“dead” times between the various phases allow the accumulation of air in areas where it is easily expelled
in the next phase)..
▶WARNING: This action is only required for the rst installation.
▶WARNING: In the event of malfunctions, the maintenance light (wrench) comes on. In this case, contact
customer service: Fill the external tank with tap water; Position a suitable container to collect the water
that is dispensed.
> Fill the external tank with tap water.
> Position a suitable container to collect the water that is dispensed
(this step will activate your lter).
NOTE: we also recommend using a support under the container to keep
it stable (see page 22).
The water supplied must not be ingested but, to avoid wasting it, you
can use it for your plants.
INSERT THE FILTER::
> Remove the protective lm from the cartridge, keeping sharp tools
away from the red circled part;
> Dip the tip of the lter (area circled in red) in a glass of water to
improve the seal of the gaskets.
> Insert the lter in the appropriate slot of your Zero taking care to keep
the ns pointing upwards and in the position indicated by the black
arrow;
> Press the lter down and turn it clockwise.
> After a 90° rotation the lter is secured (rotation limit) as shown in the
gure. If the lter does not lock, reposition it as in the previous gure
and repeat the rotation operation.
WE START THE PROCEDURE
A
B

14 15
ZERO ZERO DISPLAY STATUS:
> The water level light goes out and only the intermittent natural water
button turns on.
> The lter light stays on intermittently.
USER ACTIVITY:
> Position a suitable container (3 L) to collect the water that is
dispensed. This step will activate your lter. The collected water
must not be ingested but to avoid wasting it you can use it for your
plants.
ZERO ZERO DISPLAY STATUS:
> The natural water button comes on;.
> The lter light stays on intermittently.
USER ACTIVITY:
> Fill the external tank up to the level;
> Press the natural water button (which becomes steady during
dispensing); the lter light remains intermittent;
> The natural water button starts to flash.
ZERO ZERO DISPLAY STATUS:
> The intermittent natural water button comes on;
> The lter light stays on intermittently.
USER ACTIVITY:
> Press the natural water button again (which becomes steady
during dispensing); the lter light remains intermittent;
> The natural water button starts to flash
> Once the plug is inserted, ZERO becomes ACTIVE and is
ready for the FIRST ACTIVATION process.
> The display is activated (with a beep emitted), water level
light on and steady and lter light on and flashing and
buttons off.
C
D
E
F
CALIBRATING THE BOTTLE:
> Fill the external tank up to the level;
> Remove the container you previously placed under the water
dispenser and replace it with the supplied Happy Frizz bottle;
> The natural water button automatically acts as a guide while
flashing;
> Press the natural water button;
> When the correct level is reached (water level mark on the bottle),
press the natural water button again to stop dispensing.
Now you have calibrated your bottle of ambient water.
ZERO DISPLAY STATE:
> The internal water tank is relled;
> The cold water light comes on;
> The lter light stays on intermittently.
USER ACTIVITY:
> Press the cold water button (which becomes steady during the lling
phase).
> Remove the external tank and the lter;
> Be sure to shake the lter with the tip at the top to remove the air
inside.
> At the end of the operation, ret the lter, ll the tank and place it
back on its seat.
ZERO DISPLAY STATE:
> The crossed drop light goes out and the intermittent cold water
button comes on.
> The lter light stays on intermittently.
USER ACTIVITY:
> Place a suitable container on the drip tray again.
NOTE: If the user does not ll the tank, it does not have enough water
to ll the internal tank, then the external tank level light comes on and
when it turns off (water is available again) the machine restarts with
the internal tank lling phase
G
H
I

16 17
ZERO DISPLAY STATE:
> The cold water button turns off and, after 10 s, the natural
intermittent water button with intermittent lter light comes on.
USER ACTIVITY:
> Press the natural water button (which becomes steady).
ZERO DISPLAY STATE:
> The natural water button goes out;
> The intermittent cold water and intermittent lter indicator comes on.
USER ACTIVITY:
> Press the cold water button (which becomes xed).
ZERO DISPLAY STATE:
> The cold water button goes out;
> The intermittent cold water button comes on again;
> The lter light stays on intermittently .
USER ACTIVITY:
> Press the cold water button (which becomes xed;
NOTE: To ll the internal tank, the dispensing buttons remain off.
ZERO DISPLAY STATE:
> When the internal tank is full, the lter light goes out;
> The dispensing buttons and the temperature regulator come on (set
= 8°C).
USER ACTIVITY:
> Remove the container over the drip tray and the machine is ready
for use;
> Fill the external water tank.
ATTENTION: In the event of power outages or depletion of the external
tank water during the rst activation phase at the end user, the
machine restarts upon recovery/lling:
From the beginning, if the natural water bottle is not calibrated.
From lling of the internal tank, if the natural water bottle has been
calibrated.
In the event of problems, simply switch the machine off and on again
(or press the natural H2O key) to reset the timeout and to resume
from the point of interruption.
L
M
N
O
TANK LEVEL DEPLETION
If the user uses the water until the external tank runs out of water, the capacitive sensor detects the reaching
of the minimum level and the drop light on the display lights up.
By partially relling the external tank the crossed drop light goes off and the dispensing buttons and
temperature adjustment buttons are turned back on until stand-by. The crossed drop light also comes on
when the external tank is removed (for example for cleaning or lling).
If the external tank runs out before lling of the internal tank, in addition to the external tank level light, an
intermittent beep is activated immediately.
Simply ll the external tank.
NOTE COLD WATER DISPENSING:
During lling of the internal tank, the extraction of water is inhibited, the cold water and natural water buttons
are off. If the water in the external tank ends (with the buttons turning off and the tank level light turning on)
during the internal tank lling operations, the phase will be completed when the water in the external tank
is relled.
GENERAL NOTE WATER DISPENSING:
The user can take cold water at any time, even if the set temperature is not reached.
HOW TO CALIBRATE THE BOTTLE (in the period following the rst use):
> Keep the cold water or ambient water button pressed for 5 seconds (in the meantime the machine will
start dispensing at the rst touch without waiting for 5 seconds); during the 5 seconds DO NOT remove
your nger from the button.
> The dispensing time adjustment procedure has been activated
> The button starts flashing;
> Take your nger off the button;
> Press the button again (simply place your nger on it for a minimum of 0.3 s) to stop the water;
> At this point the new automatic open/close time is recorded.
At the end of the cold water bottle calibration the machine always lls the internal tank. Calibration of the
cold water bottle is only possible when the internal tank is full; the function is therefore inhibited after the
extraction of cold water.
The maximum cold water setting programming time is 23 s, while for the ambient temperature it is 85 s.
HOW TO SET
THE TEMPERATURE
HOW TO DISPENSE
AMBIENT WATER
HOW TO DISPENSE
COLD WATER
HOW TO USE THE HAPPY FRIZZ ZERO

18 19
TEMPERATURE CUSTOMISATION:
The user can adjust the water temperature differently than the automatic pre-set temperature (10°C), to
between a minimum of 6°C and a maximum of 30°C. The temperature adjustment buttons and the relative
indicator are not normally active (stand-by after 20 s). Pressing an active area ofthe display, the + and -
buttons come on. Pressing the buttons changes the SET temperature, which is stored.
We recommend setting the temperature between 8 and 12 degrees. This is the IDEAL TEMPERATURE
range that allows you to have cold water, reduced consumption and longevity of your ZERO system.
STAND BY - ZERO ECO MODE
After 90 seconds of inactivity of the machine (end of operations in progress, including internal tank rell, and
not pressing a button), the display goes into stand-by (display lights deactivated in fading).
Pressing the active parts of the display the machine exits stand-by, turning the dispensing buttons and the
temperature regulator back on. The temperature controller goes into standby after 20 s.
The temperature regulator does not exit stand-by in the event of the dispensing buttons being pressed. This
is due to the splitting of the display into two areas: dispensing buttons area and temperature regulation area
(to exit the temperature regulator from stand-by, press in the right area).
HOW TO INSTALL THE ZERO SYSTEM ON THE NETWORK
NETWORK CONNECTION KIT INSTALLATION
ZERO for your convenience can also be installed directly to the home network thanks to the installation kit.
Visit the website www.happyfrizz.it for further information.
ONLY INSTALL ZERO WITH THE ZERO INSTALLATION KIT. This kit alone, in addition to facilitating
installation, ensures perfect operation of your ZERO. Failure to use this kit will void the product warranty.
Carefully read the instructions in the user manual of the ZERO network installation kit.
Once installed, proceed as follows.
ATTENTION: the machine water inlet pressure must not exceed 5 bar and must not be less than 2 bar.
TRANSFER FROM WATER TANK (only if it is installed on the network)
The transition from “tank” to “water network” takes place in this manner:
→Press the sanitisation button for 5 s (button off), the natural water
button starts flashing;
→Press the natural water button, the natural water button turns off and
the sanitisation button starts flashing;
→Press the sanitisation button for 5 seconds to conrm switching to the water network.
The change from tank to the water network is also possible with an empty external tank (barred drop light
on). The customised calibration times that may have been set are reset to the default values.
In the event of an incomplete sequence (exceeding the maximum time for completing the sequence)
nothing happens.
The sequence is not possible with the sanitisation indicator on (ZERO gives precedence to this activity).
5 SEC.
At the end of the sequence open the shut-off valve.
OPEN
Once the network system is connected, we recommend that you empty
the external tank, dry it with a cloth and put it back in place on the ZERO.
You can use the external tank during the sanitisation/descaling procedure.
ATTENTION: once connected to the network, check that there are no leaks
along the path of the connection pipe and check that the same pipe is not
compressed or narrowed caused by excessive bending of the pipe.
HOW TO CARBONATE THE WATER
1. Before creating the carbonated water, ll the carbonating bottle with cold water up to the lling line.
2. Insert the bottle into the holder and twist. To facilitate twisting, pull the tube towards you to tilt the block.
Reposition the bottle in vertical position pushing it backwards (towards the body of the ZERO system).
3. Press the button on the head of the ZERO system, repeatedly for the desired carbonation level, maximum
3 or 4 short but rm pressures.
4. Once satised with the level of carbonation, pull the bottle towards you to unscrew it. Done!
PASSAGE FROM WATER NETWORK TO TANK (only if previously installed on the network)
Close the “T” shut-off valve.
The transition from “water network” to “tank” takes place in this way:
→Press the sanitisation button for 5 s (button off), the natural water
button starts flashing;
→Press the natural water button, the natural water button turns off
and the sanitisation button starts flashing;
→Press the sanitisation button for 5 seconds to conrm switching to
the tank.
I tempi di taratura personalizzata eventualmente impostati vengono
riportati ai valori di default e non a quelli precedentemente
impostati.
The customised calibration times that may have been set are reset to
the default values and not to those previously set.
In the event of an incomplete sequence (exceeding the maximum time
for completing the sequence) nothing happens.
The sequence is not possible with the sanitisation indicator on (ZERO
gives precedence to this activity.
ANTI-LEAK DEVICE
The ZERO system is equipped with a water leak detector. In the event of internal water leaks the machine
goes into “safety lock” mode and the maintenance light (wrench) is activated on the display.
In this case it is advisable to disconnect the ZERO system power socket for 10 hours. If the machine is
connected to the water mains, close the “T” valve.
After 10 hours, reconnect the power socket and, if connected to the water supply, open the “T” valve.
If the problem is not resolved, contact support.
MACHINE INACTIVE FOR A LENGTHY PERIOD
If the machine is not used for more than a week (dispensing less than 0.8 litres) after the rst activation by
the end user, the sanitisation button will light up with the possibility for the end user to carry out the same.
The calculation of the week is given by the comparison between the time counter for replacing the lter and
the litre counter. The constraint is valid both when the machine is powered by electricity and when it is not
(in this case the sanitisation button lights up together with the next activation).
PROCEED WITH SANITATION (page 22)
5 SEC.
CLOSED

20 21
Insert the inclined bottle,
twisting it into the ZERO
system.
Press the button until you
hear a venting noise.
Repeat as many times as
you wish to create sparkling
water.
Bring the bottle towards
you by tilting it, thus
allowing the excess gas to
escape.
Unscrew the bottle.
We recommend using cold water
because at low temperatures the water will
carbonate better.
ATTENTION:
After carbonating the water it is mandatory to
vent the excess gas, tilting the bottle forward,
before unscrewing it. Otherwise the pressure
accumulated inside the bottle can damage the
appliance.
O-RING SEALS:
For the operation of the appliance, there must be a seal between the
cylinder support and the cylinder valve itself.
It is located in the gas cylinder housing. Otherwise, in the absence of it, a
gas leak and/or water leak would occur during the gasication process.
If you have lost the seal, you can purchase one separately (see page
- 32).
OPEN CLOSED
KIT FOR SANITISATION/DECALCIFICATION
AND FILTER CHANGE
WHEN TO PURCHASE IT:
> When prompted by your ZERO system (1,500 L/6 months)
> After 1 week of inactivity (less than 0.8L of water supplied)
> If an additional lter change is required (little water comes out of the dispenser
due to the composition of the incoming water).
WHAT THIS PACK CONTAINS:
> 1 new lter HAPPY FRIZZ ZERO Microltration 0.5 MICRON.
> 1 sanitising/descaling sachet 12.5 g HAPPY FRIZZ SaniKit.
WHY YOU NEED THIS KIT:
> To sanitise your ZERO system;
> To decalcify the entire circuit of the system;
> To replace the used lter with the new one, guaranteeing the quality of the
water you drink.
FILTER CHANGE PREPARATION
If you are about to use this pack, it means that your ZERO system has requested a lter change, after
sanitising the system; or, due to the composition of the incoming water, you need an additional lter change.
Before replacing the used lter with the new one, make sure you have completed the assisted sanitation
process. If you have opted for an additional lter change, periodic sanitisation will not be necessary as it is
not required by your ZERO system so it is sufcient to remove the old lter and to replace it with the new one.
▶WARNINGS:
> Do not re-use the used lter.
> Do not insert a new lter if the sanitisation procedure has not been performed (if requested by your ZERO
system).
> Your Happy Frizz ZERO system is a water treatment device for human consumption. The quality of the
water you drink can only be guaranteed if the periodic sanitisation/decalcication is carried out. The
ZERO system is designed to accompany you step by step in this activity.
BEFORE STARTING THE SANITISATION/DECALCIFICATION PROCEDURE
ATTENTION: IF YOU ARE NOT READY TO CARRY OUT THE PROCEDURE AND YOU DO NOT HAVE WITH
YOU A SUITABLE 3L CONTAINER, DO NOT START THE SANITISATION DECALCIFICATION PROCEDURE.
IF THE APPLIANCE WAS INSTALLED AT THE WATER MAINS IT IS VERY IMPORTANT TO
CLOSE THE WATER FLOW AND THEN THE “T” VALVE (as shown in the photo)

22 23
IT’S TIME FOR SANITISATION - What happens to my ZERO?
COMPLETE PROCEDURE OF SANITISATION/DECALCIFICATION /
FILTER CHANGE..
STAFF NOTE
ZERO invites you to carry out the sanitisation/descaling and lter change procedure every 1500 L, or every 6
months or if the ZERO system has not been used for 1 week or more.
The next few steps may seem tedious or long; in reality it was more difcult to write them in this manual than
to actually carry them out. In any case ZERO will accompany you through these phases, step by step. It is
very important that you strictly follow the instructions below.
The rst stage of the procedure is to make sure that the sanitising/descaling powder arrives throughout the
circuit and the second part is used to rinse your ZERO well. Shall we begin?
WHAT DO YOU NEED?
> PACK KIT for sanitising/descaling and lter change (p. 21).
> 1 WATER CONTAINER OF AT LEAST 3L (we recommend a pot).
> 1 SUPPORT BASE for the container (we recommend using a kitchen cutting board).
▶WARNINGS:
> if you are not ready (Kit available and a 3L container) do not press
the button to perform the procedure.
> in case of CONNECTION TO THE WATER MAINS CLOSE THE “T”
VALVE (see page 21).
ZERO DISPLAY STATE:
> The magenta button with the “cleaning lter” symbol is on. This
means that it is time for sanitisation and lter change.
USER ACTIVITY:
> Press the magenta icon for 5 seconds to start the sanitisation
procedure.
1
ZERO ZERO DISPLAY STATUS:
> The magenta button with the “cleaning lter” symbol remains on;
> The orange light with the crossed lter symbol has come on and is
intermittent;
> The water supply buttons go out.
USER ACTIVITY:
> Remove the external tank and the used lter by turning it anti-
clockwise by approximately 90° until it is released, then lift it.
2
If this light has come on it is a
SANITISATION/DECALCIFICATION time
ZERO DISPLAY STATE:
> The magenta button with the cleaning lter symbol remains on;
> The orange light with the crossed lter symbol remains on and is
intermittent;
> The red water level light is on.
USER ACTIVITY:
> Put the external tank back in place with the sanitiser dissolved
in the water;
> Place under the water dispenser (above the drip tray) a
suitable container (min. 3 litres).
NOTE: to keep the container flat,
use a support, for example
a kitchen cutting board.
RECOMMENDATION: in case of particularly hard/calcareous
water, there may be some difculty in rotating the lter.
In this case, we advise you to try using a nutcracker or a set
of pliers by pressing on the secure grip ns.
“Good, you have removed the used lter. DO NOT INSERT THE NEW FILTER IMMEDIATELY. Zero will inform
you when to do so (see point 15). Let’s continue with the sanitisation procedure”.
USER ACTIVITY:
> Fill the external tank with tap water up to the level;
> Open the sanitising sachet and pour it into the external
previously lled tank;
> Use a spoon
▶WARNINGS FOR THE USE OF SANIKIT POWDER:
The sanitising powder should not be swallowed. Avoid contact with the eyes.
Attention.
H319 Causes severe eye irritation.
H411 Toxic for aquatic organisms with long-lasting effects.
Wash skin thoroughly after use. Do not disperse in the environment. Wear protective gloves/clothing and
protect the eyes/face.
IN CASE OF CONTACT WITH THE EYES:
Rinse thoroughly for several minutes. Remove any contact lenses if it is easy to do so. Continue to rinse. If eye irritation
persists, consult a doctor. Collect any spilled material.
3
4

24 25
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the orange light with the crossed lter symbol remains on and is
intermittent;
> the ambient temperature water icon comes on and is intermittent.
USER ACTIVITY:
> Press the ambient temperature water icon. In this way ZERO starts
the sanitisation procedure. Now the ZERO is ready to start!
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the cold water icon turns on and is intermittent;
USER ACTIVITY:
> Press the cold water icon. In this way the internal tank is emptied.
Ensure the presence of the container.
ATTENTION: ensure the presence of the 3L container.
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the ambient temperature water icon comes on and is intermittent.
USER ACTIVITY:
> Empty the 3L container and then replace it under the water
dispenser;
> Press the ambient temperature water icon. In this way the water
with the sanitiser entered the circuit and the internal tank.
> A small quantity of sanitising water is discharged into the
container (twice, 20 seconds apart). Wait for the red water level
light to come on.
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the red water level light comes on;
USER ACTIVITY:
> Remove the extruded tank, rinse it very well, ll it completely with
tap water and replace it in its seat;
> Empty the 3L container.
> Replace the 3L container.
IMPORTANT PRECAUTION:
> the tank must be well cleaned making sure that no residues remain
inside.
Let’s have a coffee and leave the sanitiser act for approximately 25 minutes. Your ZERO will notify you
when you are needed.
5
6
7
8
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the cold water icon turns on and is intermittent;
USER ACTIVITY:
> Press the cold water icon. In this way the rinsing procedure is
started and the internal circuits are emptied from the sanitiser.
> ATTENTION: ensure the presence of the 3L container.
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the ambient temperature water icon comes on and is intermittent.
USER ACTIVITY:
> Empty the 3L container and then replace it under the water
dispenser;
> Press the ambient temperature water icon. In this way the rinsing
procedure starts.
> A small quantity of sanitising water is discharged into the
container (twice, 20 seconds apart). Wait for the red water level
light to come on.
ATTENTION: wait for the ambient water icon to go out before removing
the tank, as water may still be coming out.
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the red water level light comes on;
USER ACTIVITY:
> Rinse the external tank very well, ll it with tap water and place it
in its seat again.
> Empty the 3L container and replace it;
Wait 5 minutes until Zero alerts you.
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the cold water icon turns on and is intermittent;
USER ACTIVITY:
> Press the cold water icon. In this way the water used for the rst
rinse is discharged.
9
10
11
12

26 27
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the ambient temperature water icon comes on and is intermittent.
USER ACTIVITY:
> Empty the 3L container and then reposition it under the water
dispenser;
> Press the ambient temperature water icon. In this way the system
starts the procedure for the second rinse.
ATTENTION: wait for the ambient water icon to go out before removing
the tank, as water may still be coming out.
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the orange light with the crossed lter symbol comes on and is
intermittent;
> the red water level light comes on;
USER ACTIVITY:
> Remove the external tank;
> Remove the 3L container.
> Insert the new lter;
> Remove the protective lm from the cartridge, keeping sharp tools
away from the red circled part;
> Dip the tip of the lter (area circled in red) in a glass of water to
improve the seal of the gaskets.
> Insert the lter in the appropriate slot of your Zero taking care to
keep the ns pointing upwards and in the position indicated by the
black arrow;
> Press the lter down and turn it clockwise.
> After a 90° rotation the lter is secured (rotation limit) as shown in
the gure. If the lter does not lock, reposition it as in the previous
gure and repeat the rotation operation.
NEW FILTER INSERTION
13
14
15
USER ACTIVITY:
> Fill the external tank with tap water and reposition it;
> Wait 5 minutes until ZERO alerts you (with the intermittent
coming on of the cold water icon).
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the cold water icon turns on and is intermittent;
USER ACTIVITY:
> Press the cold water icon;
> in this way the water used for the second rinse is discharged.
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the ambient temperature water icon comes on and is intermittent.
USER ACTIVITY:
> Press the ambient temperature water icon. In this phase the lter
is activated;
> Empty the 3L container and reposition it.
> Note: at this stage it is normal for water to have a lighter flow.
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the red water level light comes on;
ATTIVITA’ UTENTE:
> Remove the external tank, take out the lter;
> Shake the lter keeping facing upwards the part circled in red.
This activity is useful for improving the
lling of the lter and its duration over time.
At the end of the activity reinsert the lter
according to the previous instructions (point
15);
> Once the lter has been reinserted, ll the
external tank with tap water and reposition
it in its seat.
16
17
18
19

28 29
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol remains on;
> the ambient temperature water icon comes on and is intermittent.
USER ACTIVITY:
> Press the ambient temperature water icon.
> A small quantity of sanitising water is discharged into the
container (twice, 20 seconds apart). Wait for the red water level
light to come on.
ATTENTION: wait for the ambient water icon to go out before removing
the tank, as water may still be coming out.
ZERO DISPLAY STATE:
> the magenta button with the cleaning lter symbol is on and
intermittent;
> the red water level light comes on;
> the red maintenance light with the wrench symbol lights up and is
intermittent.
USER ACTIVITY:
> Remove the container under the water dispenser, empty it and
store it.
> Press the magenta button with the cleaning lter symbol for 5
seconds.
> Ending the sanitisation procedure.
ZERO DISPLAY STATE:
> the red water level light is always on;
USER ACTIVITY:
> EXTERNAL TANK MODE: Remove the external tank, ll it with tap
water and replace it on the ZERO;
> NETWORK MODE: simply open the T-shut-off valve and the ZERO
automatically returns to network mode.
OPEN CLOSED
20
21
22
ZERO DISPLAY STATE:
> the cold water icon comes on;
> the ambient temperature water icon comes on.
CONGRATULATIONS, YOUR ZERO IS SANITISED, DESCALED AND YOUR FILTER IS
READY TO WORK!
VERY IMPORTANT NOTES.
1. REMEMBER TO ALWAYS FILL THE EXTERNAL TANK UP TO THE LEVEL. Otherwise ZERO will run out of
water ahead of time. If it happens ZERO will resume from the previous phase.
2. THE CONFIRMATION OF THE VARIOUS SEQUENCES RELATED TO THE ACTIVATION AND SHUTDOWN
OF THE WATER LEVEL LIGHT IS RELATED TO THE REMOVAL AND REPOSITIONING OF THE EXTERNAL
TANK, IF POORLY SUPPORTED, ZERO WILL NOT CONTINUE THE PROCEDURE.
In the event you encountered any difculties, we report below all the FAQs typical for this procedure.
FAQ
1. What happens if the current jumps or if I mistakenly cut off the current? The ZERO sanitisation will
restart from the “25 minutes” phase (PHASE 8).
2. Can I stop the sanitisation once it has started? It is not possible to interrupt once the magenta
sanitisation button has been pressed because, even if ZERO is switched off, it is programmed to
reactivate from the “25 minutes” phase (pre-rinse phase) (PHASE 8).
5. If water comes out of the container for water drainage? It is important to follow the sanitisation/
descaling process step by step. If the 3L container overflows, it means that it has not been emptied
before giving the ok (icon activation) for the next action. At this point, empty the 3L container as fast as
possible.
23

30 31
SLIGHTLY SPARKLING
WATER:
Press and hold the carbonation button for 1-2
seconds and release. Remove the bottle after tilting
it.
MODERATELY SPARKLING
WATER:
A total of 2 presses guarantees moderate
carbonation. Each time the button is pressed, hold
for 1-2 seconds. Remove the bottle after tilting it.
VERY SPARKLING
WATER:
A total of 3 presses of 1-2 seconds ensures
a high degree of carbonation. Each time
the button is pressed, hold for 1-2 seconds.
Remove the bottle after tilting it.
ULTRA SPARKLING
WATER AND SOFT DRINKS:
A total of 4 presses of 1-2 seconds ensures a high
degree of carbonation. Each time the button is
pressed, hold for 1-2 seconds.
Remove the bottle after tilting it. Now you can add
your favourite concentrate!
Close the bottle and turn it upside down to help mix
the concentrate.
WARNING: YOU MAY SEE SMALL PIECES OF ICE
IN THE WATER IMMEDIATELY AFTER CARBONATION WHEN
THE WATER USED IS VERY COLD.
If this happens, shorten the time for each press until the ice
disappears. The ice created will simply melt.
CARBONATION LEVELS AND PREPARATION OF
CARBONATED DRINKS A HUGE VARIETY OF FLAVOURS AWAITS YOU THAT YOU CAN PREPARE AT HOME IN JUST A FEW SECONDS.
Not just sparkling water. Concentrates are the non plus ultra of accessories to expand the concept of
sparkling drinks.
Each bottle contains 500ml of concentrated product, equivalent to 7.5L of nisheddrink ready to
consume drink.
1 cap of concentrate = 1 bottle of nished drink
The tastes available are:
Cola, “Gazzosa”, Orange, Tonic.
+Plus
• Italian production with high quality ingredients.
• Aspartame-free.
• New pack with dosing cap.
• Reduced calories and irresistibly good.
NOT ONLY SPARKLING WATER AND NOT ONLY FIZZY DRINKS!
Numerous recipes await you to prepare imaginative cocktails at home and with friends!
RECIPE for Alcoholic CUBA LIBRE:
Ingredients:
• 3.5 cl of white rum,
• 1.5 cl of lime juice,
• Cola ll prepared with the Happy Frizz soda maker
and our Cola concentrate,
• A few slices of lime,
• Ice cubes.
• Glass: high rock Preparation: ll a glass with ice and pour over
the lime juice and rum, mix with a spoon and nish with the
Happy Frizz cola and a few slices of lime.
Discover all the Cocktail recipes on our website: www.happyfrizz.it

32 33
MAINTENANCE
BOTTLES
SAFETY INFORMATION:
▶WARNING: DO NOT WASH THE HappyFrizz® CARBONATING BOTTLE IN THE DISHWASHER IF THE
“DISHWASHER WASHABLE” SYMBOL IS NOT PRESENT. IF, IN ERROR, THE CARBONATING BOTTLES ARE
WASHED IN THE DISHWASHER, DO NOT USE THEM AND INSTEAD THROW THEM AWAY THE USE OF
BOTTLES WASHED IN A DISHWASHER AFTER WHICH THEY ARE SCRATCHED, DARKENED, WORN OR
OTHERWISE DAMAGED CAN CAUSE SERIOUS INJURY TO PERSONS.
.
→The expiry date is present on each HappyFrizz® carbonating bottle. Do NOT use out of date bottles.
→Replacement HappyFrizz® carbonating bottles are available wherever you are able to purchase a
HappyFrizz® product.
→To rinse the carbonating bottles, use cold or lukewarm but never very hot water. If necessary, for
cleaning of the carbonating bottles use a neutral dish detergent or the HappyFrizz® bottle sanitising
powder.
→Do not use abrasive cleaning products or sharp tools to clean the ZERO system. If necessary, use neutral
dish detergent and wipe gently with a damp cloth.
→Wipe up any water spills to keep the base dry.
→DO NOT immerse in water or wash in the dishwasher. Otherwise, the ZERO system could be seriously
damaged.
→Extraordinary interventions in any case require a good level of work experience. For any intervention of
this type contact the Biotech Trentino S.p.A. customer service.
LONG LIFE PACK
DISCOVER THE NEW KIT TO TAKE CARE OF YOUR
HAPPY FRIZZ PRODUCTS
INSTRUCTIONS FOR USE:
1. SANITISING POWDER FOR BOTTLES:
A: insert the powder contained in the sachet inside the
bottle full of water at room temperature.
B: Shake and leave the product to work for 20 minutes,
turning the bottle upside down to sanitise the gasket
and the cap.
C: Rinse the bottle thoroughly.
2. REPLACE OR REPOSITION THE GASKET
IN THE CYLINDER HOUSING
Including: →2 sanitising sachets
→1 reserve gasket for the ZERO soda
maker and system.
External cleaning Clean the outside with a damp cloth, do not use solvents or abrasive detergents.
See the instructions on p.12
Clean the tray and if necessary remove any residues.
Check the state and the integrity of the power supply cable.
Clean the external part with a damp cloth, do not use solvents or abrasive detergents.
After 1,500 L,/6 months/1 week of complete inactivity or if the quality of the incoming
water requires a lter change (little water comes out of the dispenser).
After 1.500 L,/6 months/1 week of complete inactivity.
Replacing the CO2 cylinder
Cleaning the drip tray
Power cable
Checking the network connection
Replacing the lter
Sanitisation
Lost the gasket?
Fix it immediately with
a new one!
and
sanitise the bottles in
just a few steps
!
REPLACING THE CYLINDER
→The CO2 HappyFrizz® cylinder is supplied. When the cylinder has run out, you can replace it with a full
one, at the sole cost of relling at an authorised HappyFrizz® dealer.
→For further information visit our website: www.happyfrizz.eu.

34 35
TROUBLESHOOTING
Before contacting the service, consult the following list of problems and their solutions.
Often the products we consider fault are in fact perfettamente funzionanti.When a customer encounters
the following problems, these are simple small oversights and are easily resolved by our customer care
service over the phone. Our aim is to avoid any shipping that would be useless and expensive.
1. THE APPLIANCE DOES NOT CARBONATE:
→Cylinder empty. Purchase a Happy Frizz rell, bringing the empty one to a point of sale.
→There are 2 gaskets (o-rings) between the cylinder support and the cylinder valve itself.
→The cylinder may have come loose. Remove the carbonating bottle, open the HappyFrizz® bottle
compartment (page 12), access the cylinder and manually tighten the cylinder, twisting it into
place. DO NOT use tools.
→Check that the carbonating bottle has been lled with water up to the lling line.
→Check that the ZERO system is in a vertical position.
2. THE APPLIANCE LEAKS DURING CARBONATION:
→Excessive lling of the bottle, beyond the level indicated on it.
→Gasket (o-ring), between the cylinder support and the cylinder valve itself, absent.
Purchase a new one.
→Too much pressure exerted on the carbonation button. Press more gently.
→Check that the bottle is tightly screwed. If the bottle has come loose, remove it and insert it again.
3. THERE ARE GAS LEAKS DURING THE GASIFICATION PROCESS:
→Gasket (o-ring), between the cylinder support and the cylinder valve itself, absent.
→Screw and tighten the cylinder into the appropriate coupling. DO NOT use tools.
4. THE APPLIANCE CONTINUES TO RELEASE GAS ALSO AT THE END OF THE CARBONATION:
→Do not remove the cylinder or the bottle. Leave the ZERO system in a vertical position.
→Do not touch the ZERO system until gas leakage has nished.
→When no more gas comes out of the machine, remove the carbonating bottle and contact the
nearest customer service centre.
5. THE CARBONATION LEVEL IS LOW:
→WARNING: Do NOT repeat the carbonation after having added the concentrate.
→If the concentrate has not yet been added, repeat the carbonation at a higher level.
→Perform carbonation using cold water.
→If the level of carbonation is still low, it is possible that the gas is depleted. Replace the cylinder.
6. THE SOFT DRINK DOESN’T HAVE MUCH FLAVOUR:
→Add more concentrate.
→WARNING: FOR SAFETY REASONS, DO NOT repeat the carbonation of an already flavoured drink.
It is possible to repeat the carbonation only of natural water or carbonated water to which no
concentrate has been added.
7. WATER IS LEAKING FROM THE EXTERNAL FITTINGS (ZERO CONNECTED TO THE WATER NETWORK):
→Push the tube towards the tting in order to connect it correctly (until you hear a click).
→Check that you have strictly followed the instructions included in the ZERO INSTALLATION kit.
8. THE MAINTENANCE LIGHT COMES ON (ZERO CONNECTION TO THE WATER MAINS):
→Check that the pipes are not bent, preventing the passage of water.
Otherwise, read the ANTI-LEAK DEVICE paragraph on page 19 of this manual.
9. THE WATER PRODUCED IS BELOW THE EXPECTED PERFORMANCE LEVELS:
→Due to the composition of the inlet water, the lter is clogged. Purchase a new lter as indicated
on page 21 of this manual.
10. THE SYSTEM NO LONGER DISPENSES WATER:
→Check that there has been no power outage. Check that the system is correctly connected to the
power outlet.
11. THE TASTE OF WATER IS POOR DUE TO THE INITIAL PERFORMANCE:
→The lter needs replacing; replace it with a new one. Proceed to sanitise the system as described
on page 19/20.
If a problem other than those listed above is encountered, visit:
www.happyfrizz.it FAQ section, or contact us. Our staff will be happy to help. FOLLOW US:
CUSTOMER SERVICE
With us you only pay the shipping costs!
REPAIR FREE OF CHARGE!
PLUS
Home collection and delivery BASIC* Only delivery to home
* This option is valid if you prefer to take
the ZERO system to the point of sale. In
this case repair times may be longer.
WHAT CAN I DO
WITH A PRODUCT
THAT DOESN’T WORK?
PRODUCT REPLACEMENT / REPAIR
WE HAVE MADE OUR
CUSTOMER SERVICE QUICK AND SIMPLE.
Contact us on our free-phone number
800.16.86.60, or from a mobile on the direct
company number 0461 17.25.792 during
offices hours.
Our staff will check immediately if the
problem encountered is operational or is due
to incorrect use. In the event of a technical
problem, they will arrange collection and
delivery conveniently at the customer’s
home.

36 37
APPLICABLE LAWS
All claims and requests for judicial or legal actions relating to the soda maker will be regulated and interpreted
according to the local regulations of the country in which the HappyFrizz® soda maker was purchased.
HappyFrizz® CYLINDERS
The ZERO system has been designed to be used with an original HappyFrizz® cylinder. The use of other CO2
cylinders is not recommended as they may not be compatible with the HappyFrizz® soda maker.
Any damage caused by the use of cylinders other than HappyFrizz® cylinders is not covered by the warranty.
Replacement cylinders can be purchased from authorised HappyFrizz® dealers.
HappyFrizz® CARBONATING BOTTLES
The soda maker is designed to be used with a suitable HappyFrizz® carbonating bottle.
Any damage caused by the use of carbonating bottles other than HappyFrizz® carbonating bottles is not
covered by the warranty.
Check the expiry date before using the carbonating bottles. Replace any expired carbonating bottles with
new bottles. Recycle expired carbonating bottles according to the local disposal regulations.
INSTRUCTIONS FOR THE DISPOSAL OF THE PRODUCT
The package consists of recyclable materials. Contact the local authorities for further information on
recycling. Product under licence.
Product under licence
Biotech Trentino S.p.A.
of H.F. Technologies
Trento - ITALIY
Distributed in Italy by:
Biotech Trentino S.p.A.
Via Innsbruck, 22 - 38121 TRENTO - ITALIA
www.biotechtrentino.it
DISPOSE OF THE PRODUCT IN ACCORDANCE WITH THE REGULATIONS:
> The ZERO system: The symbol on the appliance or on the documentation
indicates that the product must not be treated as domestic waste but must
be delivered to a suitable collection centre for the recycling of electrical and
electronic equipment.
> Disposal must take place in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling of this
product, contact the appropriate local ofce, the household waste collection
service or the store where the product was purchased.
> Outer packaging: paper/cardboard box
> Pack handle and internal packaging: in light packaging
> The bag in which zero is packed is reusable: use it to contain clothes or to
store other items.
> The lm where the lter is wrapped in the packaging.
> The used lter in the residue (after draining the remaining water into the sink).
LIMITED WARRANTY HappyFrizz®
All the necessary precautions have been taken to deliver the ZERO system in a good condition.
Biotech Trentino guarantees, based on what is stated in the terms and conditions of this limited warranty,
that the soda maker is free from defects in materials and workmanship for normal domestic use for 24
(twenty-four) months from the date of purchase.
Biotech Trentino S.p.A. engages to replace, at its own discretion, the parts that are malfunctioning or
incorrectly manufactured, only after a thorough check and after identifying poor construction.
Transportation and/or shipping costs are always payable by the purchaser in the event of incorrect use of
the warranty terms.
During the warranty period, any components that are replaced will become the property of the
manufacturer.
The ZERO system or defective parts of the same must be delivered to Biotech Trentino S.p.A. for
replacement; otherwise the replaced part will be charged to the purchaser.
This warranty can only benet the original purchaser who has complied with the normal maintenance
instructions contained in the manual.
Our warranty liability expires when: the original owner transfers ownership of the ZERO system, or changes
have been made to it.
During the use of Happy Frizz ZERO there may be situations of incorrect operation not foreseen in the
manual. These situations, completely anomalous, can be caused by environmental factors or by accidental
failures not foreseeable by the manufacturer.
This warranty does NOT cover:
→Alterazione, uso improprio, manomissione del sistema ZERO o uso professionale;
→Alteration, improper use, tampering with the ZERO system or professional use;
→Damage resulting from excessive stress such as the use of the ZERO system after nding an anomaly,
the use of improper operating methods as well as failure to observe the use and maintenance
instructions.
→Damage caused by the use of carbonating liquids other than water;
→Damage caused by the connection of ZERO to the water supply without the use of the appropriate Happy
Frizz Zero installation kit.
→Damage caused by the incorrect connection of ZERO to the water supply.
→Damage caused by problems not attributable to ZERO (overloading of electricity, lightning,
contamination of drinking water).
→Damage caused by moving or tilting ZERO when the internal tank is full.
→Storage or placement of ZERO at temperatures below +1°C.
→The use of sanitising/decalcifying liquids other than those produced and recommended for Happy Frizz
ZERO.
→Normal wear (for example, discolouration);
→Product malfunctions caused, entirely or in part, by alteration, disassembly or repair of the ZERO system
carried out by service centres other than an authorised HappyFrizz® customer service centre;
→Damage caused by the use of cylinders or carbonating bottles other than those approved by
HappyFrizz® for use with the soda maker;
→Damage caused by the use of the soda maker with an adapter/pressure reducer valve;
→Damage caused by the use of an expired, deformed or altered carbonating bottle;
→Damage caused by accidents, or by any use other than domestic;
→The carbonating bottles and cylinders.
HappyFrizz® is not responsible for incidental or consequential damages. The sole and exclusive remedy of
the consumer will be the repair or replacement based on the terms and conditions of this warranty.
To the extent that this warranty does not comply with local regulations, the warranty will be deemed modied
to comply with these regulations. The benets granted to the consumer by this warranty are in addition to
the other rights and remedies permitted by law in relation to the ZERO system.
Biotech Trentino S.p.A. assumes no responsibility for any difculties arising in the resale or use abroad due
to the provisions in force in the country where the ZERO system was sold.
TO TAKE ADVANTAGE OF WARRANTY ASSISTANCE
If the ZERO system requires assistance during the warranty period, contact the nearest HappyFrizz®
customer service centre at www.happyfrizz.eu. Our customer service will provide instructions on how to ship
the ZERO system. Any repairs performed by third parties will void the warranty.
ASSISTANCE NOT UNDER WARRANTY
If Biotech Trentino or one of its authorised agents establishes that the malfunction or damage is not covered
by warranty, Biotech Trentino will carry out the repair of the ZERO system exclusively upon payment of the
amount necessary for the repair.
WARRANTY WARNING
If part of this user manual is also partially illegible or missing, consult the [email protected] customer
service before carrying out any further operations on the machine.
The persons who will use the ZERO system and undertake its maintenance must read the use and
maintenance manual, paying particular attention to the general safety rules and to the methods of execution
contained in the sections relating to the operations for which they are responsible.

38 39