Harison R470M User manual

Adjustable Roller
Lock knob (K1)
Pointer Lock
Knob (K2)
Pointer
How To Use:
Mode 1 [ Manual Mode ]
Instruction Sheet
Rotary Turn-Table R470M
Package Contents
Specification:
Diameter:
460 mm
Max Speed:
3.5 rpm
Min Speed:
0.3 rpm
7.5 Kg
Max Load:
(K1)
Adjustable
Roller (R1)
Motorised Roller (M1)
Central Spindle (SP1)
9.
2
4
5
5
67
3
1
1. Base Plate (White Diffuser) (W1) 1 Pc.
2. Base Plate (Transparent) T1 1 Pc.
3. Power Adaptor 1 Pc.
4. Motor Controller 1 Pc.
5. Cross Base 1 Pc.
6. Carry Bag 1 Pc.
7. Instruction Manual 1 Pc.
Turn the knob (K1) anti-
clockwise to loosen it.
(Note: only 1-2 turns of
the knob are sufficient
to loosen it)
1.
Place the Base plate (T1)
by aligning its central hole
(H1) with the central spindle
(SP1) Press down gently so
that the (SP1) fits snugly
into hole (H1)
6.
Central
Hole (H1)
Base Plate
(T1)
Base Plate
(W1)
Rotate the rotary plate by hand
so the number ‘1’ aligns with the
pointer as shown:
8.
Place the second base plate
(White Diffused) (W1) on the
transparent base plate so
that the edges of both base
plates align.
(K2)
Once loose move the pointer to the
position as shown:
Tighten the knob K2 by turning it
clock-wise. A dimple in the pointer
base will match with an alignment slot
so as to position the pointer correctly.
5.
4.
The Rotary Turn-Table is now
ready to be used in the manual
mode.
7.
Note: R1 Should be at
a higher level to M1
}
(K1)
(R1)
M1
Lock by turning knob
(K1) clock-wise.
2b.
2a.
Loosen the pointer
tightening knob (K2) by
turning it anti-clockwise
3.
R
Raise the knob
( and the roller R1)
upwards.

Mode 1 [ Manual Mode to continue... ]
Connect the power adopter (P1) to the motor controller (C1).
Connect the motor controller to the socket in the base (B1).
The socket has ‘MOTOR’ printed next to it.Upon switching ON
the AC supply, the indicator (L1) will glow.
2.
HARI SINGH & SONS (An ISO 9001 : 2000 Company) G.T. Road, Near Canal, P.O. Sultanwind, Amritsar - 143021, INDIA.
Phone: [phone] E-mail: [email protected] URL: harisonphoto.com
C1
L1
K3
B1
P1
Control the rotation of the base plate as follow:
1st press of B2 Rotary Turn-Table move clock-wise
2nd press of B2 Rotary Turn-Table move anti-clockwise
Press B2 for 2 sec Rotary Turn-Table will stop
The speed controller knob (K3)
can be used to vary the speed of
rotation.
3.
4.
5.
Place the object to be photographed in the
center of the rotary plate.
Position your video camera on a tripod
and shoot the video.
K3
B2
L1
Then move the rotary
plate gently with your
h a n d t o th e nex t
division.
Click another picture.
By repeatedly moving
the base plate by each
division you can thus
click 144 pictures in
high resolution.
Each picture will be of
the object rotated by 2.5
degrees.
P l a c e t h e o b j e c t t o b e
photographed in the center of the
rotary plate. Position your camera
on a tripod and click a picture.
Move the base plate with
your hand so that the pointer
aligns with ‘01’.
(A) (B) (C)
Run the image in a sequence by using a suitable software application to obtain a high resolution 360 degree product video !
Mode 2 [ Video Mode ]
1a.
1b.
1c.Lock R1 in place by turning knob (K1) clock-wise.
Turn the knob K1 anti clock-
wise (2-3 turns) to loosen it.
Lower the knob K1 ( and the
roller R1) .
(K1)
(R1)
R1
K1
M1
}
Note: Ensure that R1 is
at lower level than M1.