Vivo DESK-E3CTB-75 Series User manual

Follow along step-by-step with our video walk through by scanning
the QR code with your mobile device or by following the product
link: vivo-us.com/products/desk-e3ctb
ASSEMBLY VIDEO AVAILABLE:
[email protected]om www.vivo-us.com 309-278-5303
63” x 75” Corner Electric Desk
Instruction Manual
SKU: DESK-E3CTB-75 SERIES
Frame:
DESK-E375B
DESK-E375W
Table Top:
DESK-E3CTB-75-A
DESK-E3CTN-75-A
DESK-E3CTW-75-A

Contact Us First!
PERSONABLE CUSTOMER SUPPORT
Our friendly product support team is here to help!
DO NOT RETURN ITEM
We’re Here for You!
Missing a Part?
Our customer-minded support team is here for YOU,
Monday-Friday 7am-7pm CST.
We oer immediate assistance with rapid response times
from customer service agents and product techncians to
help you every step of the way!
Monday-Friday
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om
If any parts are received damaged / defective OR you are
missing a part, please reach out to us within 30 days of
product delivery to have it replaced at no cost.
We are happy to replace parts to ensure you have a fully
functioning product
7AM - 7PM

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a qualified
technician. Check carefully to make sure there are no missing
or defective parts. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We
cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
PRE-ASSEMBLY | BEFORE YOU BEGIN
Product Warranty
Returns | Product Didn’t Work Out?
For the most up to date details on your product’s warranty, please visit
the product’s listing on our website or reach out to customer support.
vivo-us.com/products/desk-e3ctn-75
We oer a hassle-free 30 day return on all products. Contact customer
support at 309-278-5303 or [email protected]om. Please note: For items
ordered in error or no longer needed, the return shipping charges will
be at the buyer’s expense.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS
REQUIRED.
WEIGHT CAPACITY
DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.
176lbs
(80kg)
!
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
ELECTRICAL WARNING :

4
PACKAGE CONTENTS
Please consult the parts list below and ensure you have everything you need to assemble
your product. If parts are missing or damaged, please contact us.
Phillips Screwdriver
|
TOOLS NEEDED:
DIFFICULTY LEVEL
Level
S-A x18)
M6x8mm Screw
S-B (x9)
M6x35mm Screw
S-C (x43)
ST5x16mm Screw
T-A (x1)
5mm Allen Wrench
T-B (x1)
2mm Allen Wrench
S-D (x6)
M6x11mm Screw
A (x1)
Desktop Panel A
F (x1)
Long Corner Crossbar
K (x1)
Motorized Leg
R (x2)
Foot
S (x1)
Control Panel
T (x1)
AC Adapter
U (x1)
Extension Cable
M (x1)
Le Leg
N (x1)
Connector Bracket
O (x1)
Inner Crossbar
Q (x2)
Connector Plate
G (x1)
Angled Outer Crossbar
B (x1)
Desktop Panel B
C (x1)
Desktop Panel C
H (x1)
Short Sync Rod
J (x2)
Side Bracket
L (x1)
Right Leg
D (x1)
Straight Outer Crossbar
E (x1)
Short Corner Crossbar
W (x2)
Cable Clip
V (x21)
Anti-Vibration Pad
I (x1)
Long Sync Rod
P (x2)
Connector Bar
NOTE: Extra Hardware Included

5
T-A
5mm Allen
Wrench
STEP 1: Assemble Le Leg
ASSEMBLY STEPS
Attach Straight Outer Crossbar (D) to Le Leg (M) using M6x8mm Screws (S-A) and 5mm Allen
Wrench (T-A).
M (x1)
Le Leg
J (x1)
Side Brackets
D (x1)
Straight Outer
Crossbar
S-A x4)
M6x8mm Screw
D
T-A
M
S-A
JT-A
S-A
M
Attach Side Bracket (J) to Le Leg (M) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-A).

6
STEP 2: Assemble Right Leg
Attach Angled Outer Crossbar (G) to Right Leg (L) using M6x8mm Screws (S-A) and 5mm Allen
Wrench (T-A).
G
L
S-A
T-A
L
J
S-A
T-A
Attach Side Bracket (J) to Right Leg (L) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-A).
G (x1)
Angled Outer Crossbar
L (x1)
Right Leg T-A
5mm Allen Wrench
J (x1)
Side Brackets
S-A x4)
M6x8mm Screw

7
F (x1)
Long Corner
Crossbar
E (x1)
Short Corner
Crossbar
K (x1)
Motorized Leg
R (x2)
Foot
S-B (x8)
M6x35mm Screw
T-A
5mm Allen
Wrench
S-A x4)
M6x8mm Screw
STEP 3: Install Feet & Connect Motorized Leg
Attach Feet (R) to Le and Right Legs (M,L) using M6x35mm Screw (S-B) and 5mm Allen
Wrench (T-A).
R
L
S-B M
T-A
Connect Short Corner Crossbar (E) and Long Corner Crossbar (F) to Motorized Leg (K) using
M6x8mm Screws (S-A) and 5mm Allen Wrench (T-A).
K
E
F
S-A
T-A

8
- Assembly Options -
This desk can be assembled with a le or right side extension.
Please select an option and proceed with assembly
Option B | Right Side Extension
Desk frame will extend out to right
side, with a short le side
Pg 15-20
Option A | Le Side Extension
Desk frame will extend out to le
side, with a short right side
Pg 7-10

9
A-STEP 4: Install Anti-Vibration Pads
ASSEMBLY OPTION A | Le Side Extension
Aix Anti-Vibration Pads (V) to the desk frame and Connector Bracket (N).
V (x19)
Anti-Vibration Pads
N (x1)
Connector Bracket
V
N

10
A-STEP 5: Assemble Desktop
Lay out the desktop panels in the configuration shown in the image with the pilot holes facing
up. Use the pilot holes to verify the tops are in the correct orientation.
Connect Desktop Panels (A,B,C) together using Connector Bars (P), Connector Plates (Q),
ST5x16mm Screws (S-C), and a Phillips Screwdriver.
A (x1)
Le Desktop
Q (x2)
Desktop
Connector
B (x1)
Middle Desktop
C (x1)
Right Desktop
S-C (x20)
ST5x16mm
Screw
B
A
C
P
Q
P (x2)
Connector Bar

11
A-STEP 6: Combine Leg Sections
Place the leg sections on the desktop assembly as shown with the mounting holes aligned with
the desktop pilot holes. Attach Connector Bracket (N) to Angled Outer Crossbar (G) and Long
Corner Crossbar (F) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-A). Slide Inner
Crossbar (O) into Short Corner Crossbar (E) making sure the slotted section is facing towards
the motor. Slide the leg assembly with Straight Outer Crossbar (D) over Inner Crossbar (O).
Make sure the frame mounting holes are aligned with the desktop pilot holes and fasten Inner
Crossbar (O) using M6x11mm Screws (S-D) and 5mm Allen Wrench (T-A).
S-A x4)
M6x8mm
Screw
T-A
5mm Allen
Wrench
S-D (x4)
M6x11mm
Screw
Inside
T-A T-A
N
G
S-A
S-D
F
E
O
D
O (x1)
Inner Crossbar

12
A-STEP 7: Secure Frame & Desktop
S (x1)
Control Panel
Secure the frame assembly to the desktop using ST5x16mm Screws (S-C) and a Phillips
screwdriver. Attach Control Panel (S) to the desktop using ST5x16mm Screws (S-C) and a
Phillips screwdriver.
S-C (x21)
ST5x16mm Screw
S-C S-C
S

13
H (x1)
Short Sync Rod
T-B (x1)
2mm Allen Wrench
A-STEP 8: Install Sync Rod
Insert the hex sha end on Long and Short Sync Rods (I,H) into Le and Right Legs (M,L)
making sure the metal retaining ring makes contact with the leg. Ensure all three legs are at the
same height. If they are not, turn the sync rod clockwise to raise and counterclockwise to lower
the legs.
Loosen coupling nuts on Sync Rods (I,H) and extend onto Motorized Leg (K). Tighten coupling
nuts, then tighten both set screws on the end of Sync Rods (I,H) using 2mm Allen Wrench (T-B).
Coupling Nut
T-B
I (x1)
Long Sync Rod
M
L
K
I
H

14
W (x2)
Cable Clips
T (x1)
AC Adapter
U (x1)
Extension Cable
A-STEP 9: Connect Power Cables
Connect AC Adapter (T) and cable from Motorized Leg (K) to the back of Control Panel (S). If
needed, use Extension Cable (U) for cable from Motorized Leg (K) to extend length. Use Cable
Clips (W) to secure cables to the desktop.
T
K
S
U
W

15
B-STEP 4: Install Anti-Vibration Pads
ASSEMBLY OPTION B | Right Side Extension
Aix Anti-Vibration Pads (V) to the desk frame and Connector Bracket (N).
V (x19)
Anti-Vibration Pads
N (x1)
Connector Bracket
V
N

16
B-STEP 5: Assemble Desktop
Lay out the desktop panels in the configuration shown in the image with the pilot holes facing
up. Use the pilot holes to verify the tops are in the correct orientation.
Connect Desktop Panels (A,B,C) together using Connector Bars (P), Connector Plates (Q),
ST5x16mm Screws (S-C), and a Phillips Screwdriver.
C
B
A
A (x1)
Le Desktop
Q (x2)
Desktop
Connector
B (x1)
Middle Desktop
C (x1)
Right Desktop
S-C (x20)
ST5x16mm
Screw
P (x2)
Connector Bar
S-C
P
Q

17
B-STEP 6: Install Connector Brackets
Place the leg sections on the desktop assembly as shown with the mounting holes aligned with
the desktop pilot holes. Attach Connector Bracket (N) to Straight Outer Crossbar (D) and Short
Corner Crossbar (E) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-A). Slide Inner
Crossbar (O) into Long Corner Crossbar (F) making sure the slotted section is facing towards
the motor. Slide the leg assembly with Angled Outer Crossbar (G) over Inner Crossbar (O).
Make sure the frame mounting holes are aligned with the desktop pilot holes and fasten Inner
Crossbar (O) using M6x11mm Screws (S-D) and 5mm Allen Wrench (T-A).
S-A x4)
M6x8mm
Screw
T-A
5mm Allen
Wrench
S-D (x4)
M6x11mm
Screw
Inside
O (x1)
Inner Crossbar
N
T-A T-A
S-A
S-D
D
E
O
F
G

18
B-STEP 7: Secure Frame & Desktop
Secure the frame assembly to the desktop using ST5x16mm Screws (S-C) and a Phillips
screwdriver. Attach Control Panel (S) to the desktop using ST5x16mm Screws (S-C) and a
Phillips screwdriver.
S-C
S-C
S
S (x1)
Control Panel
S-C (x21)
ST5x16mm Screw
S-C

19
B-STEP 8: Install Sync Rod
Coupling Nut
T-B
Insert the hex sha end on Long and Short Sync Rods (I,H) into Le and Right Legs (M,L)
making sure the metal retaining ring makes contact with the leg. Ensure all three legs are at the
same height. If they are not, turn the sync rod clockwise to raise and counterclockwise to lower
the legs.
Loosen coupling nuts on Sync Rods (I,H) and extend onto Motorized Leg (K). Tighten coupling
nuts, then tighten both set screws on the end of Sync Rods (I,H) using 2mm Allen Wrench (T-B).
H (x1)
Short Sync Rod
T-B (x1)
2mm Allen Wrench
I (x1)
Long Sync Rod
K
M
L
I
H

20
B-STEP 9: Connect Power Cables
W
W (x2)
Cable Clips
T (x1)
AC Adapter
U (x1)
Extension Cable
Connect AC Adapter (T) and cable from Motorized Leg (K) to the back of Control Panel (S). If
needed, use Extension Cable (U) for cable from Motorized Leg (K) to extend length. Use Cable
Clips (W) to secure cables to the desktop.
U
S
T
K