Thomann
GmbH
•
Hans-
Thomann-Straße
1
•
96138
Burgebrach
•
www
.thomann.de
•
[email protected] DocID: 116684_03.12.2020For the packaging, environmentally friendly materials have been chosen that can be
supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly dis-
posed of. Do not just dispose of these materials with your normal household waste, but
make sure that they are collected for recycling. Please follow the notes and markings on
the packaging.
Remove lithium batteries from the device before disposal. Protect used lithium batteries
against potential short circuits, e.g. by covering the poles with adhesive tape. Dispose the
solid state lithium batteries together with the device. Please check for an appropriate
reception facility.
This product is subject to the European Waste Electrical and Electronic Equipment
Directive (WEEE) in its currently valid version. Do not dispose with your normal
household waste. Dispose of this device through an approved waste disposal rm or
through your local waste facility. When discarding the device, comply with the rules
and regulations that apply in your country. If in doubt, consult your local waste dis-
posal facility.
EN
Operating the device
Hold the power switch öpressed during 2 seconds to turn on the device. Press the
power switch again to select the operating mode Tuner (T), Metronome (M) or Tone
generator (S). Hold the power switch öpressed again during 2 seconds to turn o the device.
The device will be turned o automatically after 3 minutes of inactivity.
Tuner
1. Turn the device on and select the operating mode Tuner (T).
2. Slide the switch VIB/MIC )to the left (vibration tuning) or to the right (microphone
tuning) to select the tuning mode.
The vibration sensor provides tunings without any inuence or surrounding noise.
3. Press M/B #to select the instrument to be tuned:
chromatic (C), guitar (G), bass (B) or violin (V). The selected instrument is shown on
position Din the display.
In case of chromatic (C) press KEY $to select the tuning scale (C, Bb, Eb, F). The select-
ed tuning scale is shown on position Fin the display.
Note
The tuning scales for guitar (G) and bass (B) are set on Cand can’t be changed.
4. Use (to select between standard tuning and at tuning. Each time pressing the
button on semitone (b, bb, bbb, bbbb) is shown on position Ein the display.
Note
Absence of bindication shows the standard tuning.
5. Press CALIB &to change the calibation (that is reference tone).
The reference pitch can be varied within the range of 430-450 Hz with 1 Hz step
of increment. Hold CALIB &pressed to advance the frequency automatically. The
selected calibration is shown on position Bin the display.
6. When the instrument plays a tone, this tone will be shown in the display.
7. Tune the instrument to get the name of the desired note shown in the meter display.
If the tone is too high or too low, the needle is not in the middle of the meter display
and the LED lights red. When the tuning is correct, the LED lights green and the
needle is on position Hin the meter display.
Metronome
1. Turn on the device and select the operating mode Metronome (M).
2. Use VOLUME %to select the desired volume in four steps.
The selected volume is shown on position Ain the display.
3. Use M/B #to select the desired Beat from 0 to 9.
The selected beat is shown on position Fin the display.
4. Use (to select the desired rhythm ( ).
The selected rhythm is shown on position Cin the display.
5. Press CALIB &to increase the tempo, press KEY $to decrease the tempo.
Hold CALIB &or KEY $pressed to increase or decrease the tempo continuously in a
range from 30-250 bpm.
The selected tempo is shown on position Bin the display.
Tone generator
1. Turn the device on and select the operating mode Tuner (T).
2. Press M/B #to select the instrument to be tuned:
chromatic (C), guitar (G), bass (B) or violin (V). The selected instrument is shown on
position Din the display.
Note: This selection can not be changed in the tone generator mode.
3. Press the power switch öto enable the Tone generator (S).
4. Use VOLUME %to select the desired volume in four steps.
The selected volume is shown on position Ain the display.
In case of chromatic (C) press KEY $to select the tuning scale (C, Bb, Eb, F). The selected
tuning scale is shown on position Fin the display.
Note
The tuning scales for guitar (G) and bass (B) are set on Cand can’t be changed..
5. Press CALIB &to change the calibation (that is reference tone).
The reference pitch can be varied within the range of 430-450 Hz with 1 Hz step of
increment. Hold CALIB &pressed to advance the frequency automatically. The selected
calibration is shown on position Bin the display.
6. Press (to increase the note, press M/B #to decrease the note. The selected note is
shown on position Gin the display.
Remove the device from the instrument after tuning.
Leaving the device attached for a longer period of time may damage the
surface of the instrument.
Battery replacement
When the display brightness decreases, replace the battery.
Replace the battery with a new battery of the same type.
MT100 Tuner
Rotating
sens
A: Open the battery compartment B: Insert the battery C: Close the battery compartment
