HARVER CN50LH-2kw + 2kw User manual

SPLIT MAGNETIC INDUCTION
WATER HEATER
BY
HARVER
INSTRUCTION MANUAL
CN50LH-2kw + 2kw
CN75LH-2kw + 2kw

Thank you for purchasing and using our product.
Please read this instruction manual carefully before
using the unit and keep this manual for future
reference
CONTENTS
PRODUCT INFORMATION-----------------------------PAGE 2
SAFETY PRECAUTIONS---------------------------------PAGE 3
INSTALLATION PRECAUTIONS----------------------PAGE 4
TROUBLE SHOOTING CODES-------------------------PAGE 5
TECHNICAL SPECIFICATIONS-------------------------PAGE 5
HEATING TIMES-----------------------------------------PAGE 5
INSTALLATION INSTRUCTIONS----------------------PAGE 6/7
Page1

1. PRODUCT INFORMATION
This product has been developed from Western Harver
Technology and also using new temperature sensing technology.
These units are tested to CE specification and l local SANS &
NRCS requirements have been installed and passed.
The unit is split into two parts, the storage tank and the
generator unit.
The process of heating the water uses magnetic induction, which
heats the water more rapidly than conventional water heaters.
The electrical supply to the generator is converted into a
magnetic energy that then causes a resistance field which in
turn heats the water. This means that there is no direct electrical
a/c current in close proximity to the water, making it safer.
The unit uses new temperature sensing technology that is more
accurate. There is a high density thermal insulation layer, to
sustain the water temperature.
All these processes increase the efficiency and therefore save
electricity.
There are several protection systems in place such as: dry burn,
over heat, low/ high voltage, surge and over heat protection.
PLEASE NOTE –THIS UNIT IS NOT AN INSTANTANEOUS WATER
HEATER
Page 2

SAFETY PRECAUTIONS
Please ensure the amp rating of the socket is rated above that of
the unit.
To avoid damage and chance of electric shock, please do not wet
the generator unit.
Do not put any metal object into the exhaust duct of the
generator unit to avoid electric shock.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person
in order to prevent a hazard.
Do not block the air intake or exhaust vent of the generator unit.
Allow 150mm free space around generator intake/exhaust ports
Do not place objects that are affected by magnetism such as
watches, radios, televisions, bank cards etc .near the unit.
Persons with pacemakers, please consult your doctor before
using.
It is recommended to remove the drain plug to remove the dirty
water annually
Place unit out of reach of children and make sure children are
supervised in the use of the hot water.
People that are mentally challenged or physically handicapped
must be supervised in the operation of this unit.
If there any defects or malfunction that are not able to be fixed
by switching the unit off and then on –please contact after sales
service. Water may drip from the discharge pipe of the
expansion control valve and that this pipe must be left open to
the atmosphere. Discharge pipes connected to the expansion
control valve and the TP valve are to be of metal and installed in
a continuously downward direction, in a frost-free ambient with
the outlet being left open to the atmosphere.
DO NOT attempt to repair the unit yourself.
Page 3

3.
DO NOT ATTEMPT TO INSTALL THE UNIT AS PER THE PICTURES BELOW
THE UNT WILL NOT OPERATE CORRECTLY AND WILL CAUSE A DRY
BURN ERROR
THE WARRANTY WILL BE NULL AND VOID
Page 4

5. TROUBLE SHOOTING CODES.
E0 No power output.
E1 Input voltage low (less than 90 volts a/c)
E2 Input voltage high (above 270 volts a/c)
E4 Electronics temperature too high
E5 No water in heater (dry burn)
E6 Unable to read temperature output
6. TECHNICAL SPECIFICATIONS
7. HEATING TIMES
Page 5
Unit
50 Litre
75 Litre
Power supply
230V 50Hz
230V 50Hz
Rated Power
2000w+2000w
2000w+2000w
Rated Current
9 amp + 9 amp
9amp + 9 amp
Water
pressure
600 kpa
600 kpa
Waterproof
Level
IPX4
IPX4
Dimensions
mm
1180 x 440 x 240
1550 x 440 x 240
Time to heat water per 1 deg.
Unit
50 Litre
75 Litre
2KW
1.3 min
4KW
0.7 min
0.9 min

1
DRILL TWO HOLES INTO WALL
FIT SUPPLIED RAWL HOOKS
HANG MAIN UNIT ON HOOKS
NOTE: UNIT IS A HORIZONTAL
WALL MOUNTED
PLUMB UNIT INTO WATER
SUPPLY AS PER PLUMBING
DIAGRAM
FILL UNIT WITH WATER
BEFORE APPLYING
ELECTRICAL POWER TO UNIT
ENSURE ALL AIR IS OUT OF
UNIT BY OPENING HOT
WATER OUTLET TO ALLOW
AIR TO ESCAPE
2
FIT GENERATOR UNIT ON
LEFT SIDE OF UNIT.
PLUG INTO WALL SOCKET
CONTROLS WILL FACE TO
REAR
NOTE: LEFT UNIT
CONTROLLED BY RIGHT
UNIT. NO NEED TO PRESS
THE POWER BUTTON
ALLOW 150MM FREE
SPACE AROUND
INTAKE/EXHAUST DUCTS
3
FIT GENERATOR UNIT ON
RIGHT SIDE OF UNIT.
PLUG INTO WALL SOCKET
NOTE: UNIT WITH SPEC
LABEL IS RIGHT SIDE
MASTER UNIT.
DOUBLE SOCKET WITH
25AMP CB and 2.5mm
TO BE USED
ALLOW 150MM FREE SPACE
AROUND INTAKE/EXHAUST
DUCTS
4
SWITCH ON AT WALL PLUGS
INDICATOR LIGHT ON RIGHT
UNIT WILL FLASH
ONE BEEP WILL SOUND
38 WILL APPEAR ON DISPLAY
ON RIGHT SIDE & WATER
TEMP AFTER 5 SECONDS
5
WAIT 2 MIN - UNIT WILL
SWITCH ON
(RECOMMENDED)
OR
PRESS POWER BUTTON
ONCE UNIT WILL START
75 SHOWS ON DIGITAL
READOUT FOR 5 SEC
TEMP SHOWS AFTER 5 SEC
6
UNIT WILL HEAT TO 75° C
TO ADJUST TEMP SETTING
PRESS TEMP BUTTON –
TEMP SETTING WILL SHOW.
PRESS TO CHANGE TEMP
SETTING BY 5 DEG FROM
40-75 DEG
INSTALLATION DIAGRAM CN50L
NOTE:
COLD WATER SUPPLY SHOULD COME FROM ABOVE UNIT TO PREVENT
UNCONTROLLED DRAINAGE
1) THIS UNIT MUST BE INSTALLED AS PER THE DIAGRAM
2) THIS IS A WALL MOUNTED UNIT (HORIZONTAL ONLY)
3) NOTE: IT CANNOT BE POSITIONED UPRIGHT OR LAID DOWN ON A SHELF OR THE
FLOOR
4) ENSURE THE T\P VALVE IS 600 kpa AND IS PLUMBED TO THE DRAIN OR ATOMSHPERE
IN A SAFE AREA
5) A THERMOSTATIC TEMPERING VALVE SHOULD BE USED IF THE TEMPERATURE IS SET
ABOVE 65 DEG.
6) THE MULTI VALVE MUST BE AN APPROVED MAKE AND A 400 KPA VALVE IS
RECOMMENDED
7) ENSURE THE ELECTRICAL SUPPLY IS CAPABLE OF 22 AMPS WITH 2+2 KW UNITS (Min
2.5mm² cable)
8) DO NOT REMOVE 15 AMP PLUG –WARRANTY IS AFFECTED
9) DRIP TRAY REQUIRED IF INSTALLED IN ROOF OR CUPBOARD
10) ALLOW 150mm OPEN AREA ON GENERATOR FAN DUCTS
IF FITTED IN A CUPBOARD DIMENSIONS MUST BE:
50LH–170(W)x100(H)x40(D) cm
75LH–190(W)x100(H)x40(D) cm