Harvest Technology RiS NCMR User manual

™
AUDIO
INTERFACE
NCMR
®
Quick Start Guide

®
2
Overview
In the Box
Two-way audio streaming solution
NCMR NCMR
5V USB-C PSU
USB-C to USB-C cable USB Speakerphone
RiS Nodecom (NCMR) WiFi Antenna
Welcome to the Nodestream RiS Nodecom (NCMR)
Please read these instructions carefully before using this product, and save this
quick start guide for future use. See the User Manual for full details via the QR code
on the back page.

®
3
Overview
Rear Connections
User Interface
Status LED
Indicator Volume
Start/Stop software
Ensure adequate spacing to allow cooling air to travel through vents as shown by
the arrows
WiFi
Antenna
Ethernet
USB-A
DC in
PTT (push to talk) button
with LED indicator

®
4
Conguration
1Connect the RIS Nodecom device to your LAN via the Ethernet port
and power the device
2Congure the IPv4 settings of a computer connected to the same network
IP 192.168.2.x
Subnet 255.255.255.0
Gateway 192.168.2.1
3Navigate to http://192.168.2.1 from a web browser and login with
User admin
Password admin
4When prompted, enter a new password
User Manual
Refer to the RIS Nodecom user manual for additional information.
5Congure device network settings as provided by your Network
Administrator
Via web browser
• RiS networks require specic port settings, see user manual for details
• Devices need to be manually added to the Deliverer application. See Deliverer
User Manual for more information
Due to the possibility of conicting IP addresses, only 1 device can be congured at a
time. Once network settings have changed, the device can remain connected
Once connected and congured on your local network, the RiS Nodecom
device will show online in the Harvest RiS Deliverer application and will be
ready for connection to another device.
6

®
5
Operation
Status LED
PTT (Push To Talk)
VOL (Volume)
Factory Reset
Mute
Decrease volume until
LED is rotating
Increase volume
Turn clockwise
Decrease volume
Turn counter-clockwise
LED Ring
+
-
+
-
Press to toggle through
audio devices
(Blue)
(Red)
(Green)
Speaker
Microphone
Monitor
Device will reset to factory default user login and network settings
AUDIO
INTERFACE
NCMR
Press and Hold
Open Mic
Start talking
Press 3 times to
open mic
Press & hold
PTT & VOL
buttons
(ashes)
LED
Red
LED
Red
PTT & VOL
LED
LED
Green
LED
Green
Press for 1
sec to mute
Release to
mute
Software not running
Software running
Audio connection active, mic muted
Audio connection active, mic open
(Off)
(Blue)
(Green)
(Red)
Power on (blue)
PTT & VOL
LED
(solid)
Release
PTT & VOL
buttons
Approximately 10 seconds

Troubleshooting
Issue Cause Resolution
Device not powering AC or DC not connected.
Faulty or incompatible PSU
Conrm PSU in plugged in and AC supply on
Conrm USB-C cable is connected correctly
Test with alternative PSU
If using an alternative PSU ensure it meets
required specications, see User Manual
Network issue
(Device showing “ofine” in
Deliverer application)
Network not connected or out of
range
Network settings incorrect
Device IP address incorrect in
Deliverer application
Check Ethernet cable or WiFi is connected
Ensure antenna is correctly installed
Check network settings, contact your
network administrator to diagnose network
Conrm IP address of device matches that
set in Deliverer
Forgot login or network
details
N/A Factory reset to defaults
(see “Factory Reset” on page 5)
Contact and Support
suppor[email protected]
User Resources
®
All rights reserved. This document is the property of Harvest Technology Pty Ltd. No part of
this publication may be reproduced, stored in a retrieval system or transmitted in any form or
by any means, electronic, photocopy, recording or otherwise without the written consent of the
Managing Director of Harvest Technology Pty Ltd.
Harvest Technology Pty Ltd
7 Turner Ave, Technology Park
Bentley WA 6102, Australia
www.harvest.technology
HTG-TEC-GUI-018_0