Hausmann 1560-65-036 Installation instructions

Rev. 102413 aj Page 1of 3©2013 HAUSMANN INDUSTRIES, INC.
HAUSMANN INDUSTRIES, INC.
130 Union St • Northvale NJ 07647 USA • Tel: [phone] • Fax: [phone] • www.hausmann.com
Installation/Operation Instructions
Model # 1560-65-036 - Convertible Staircase
A) INSTALLATION INSTRUCTIONS:
1. Unpack all contents from shipping carton; confirm correct parts & quantity.
2. Place all the parts in the desired location for assembly. Model # 1560-65-036 can be assembled in two configurations
(Straight or Corner).
3. Layout the base ‘A’ and Step sections ‘C’ or ‘D’ by mounting the wooden “cleat” on opposite sides for a Straight setup
or next to each other for a Corner setup.
Model # 1560-65-036
PART
QTY
DESCRIPTION
A
1
Base
C
1
4-Step Stair Case
D
1
6-Step Stair Case
E
2
Straight Handrails
F
2
Medium Handrails
G
2
Long Handrails
H
4
57 ½” Uprights for Straight Handrails
I
2
54” Uprights for Handrails
J
2
52 ¾” Uprights for Handrails
K
2
46” Uprights for Handrails
L
2
40 ¼” Uprights for Handrails
M
2
37 ¾” Uprights for Handrails
Tools Required:
Allen Wrench (included)
Philips Screw Driver
Product Specifications
Model
Length
Width
Height
(Platform)
Weight
Capacity
1560-65-036 (Straight)
109”
36”
24”
350 lbs
1560-65-036 (Corner)
64” x 82”
36”
24”
350 lbs
HARDWARE BAG
PART
QTY
DESCRIPTION
P
8
3¼” Allen Hex Head Bolt
Q
14
2 3/8” Allen Hex Head
Bolt
R
34
45mm Pan Head/Philips
screw
S
34
16mm Barrel Bolt
T
1
4mm Allen Wrench
U
34
Flat Washer
Figure 1: Model # 1560-65-036 Corner Set-Up
Figure 2: Model # 1560-65-036 Straight Set-Up
Straight Set-Up
H
c
D
E
G
F
I
A
K
J
M
L
D
Corner Set-Up
2 People Required for Assembly

Rev. 102413 aj Page 2of 3©2013 HAUSMANN INDUSTRIES, INC.
4. Lift the Step sections up and over the “cleat” to set them into place as shown in Figure 3.
NOTE: Each upright and step section is machined with an indexing mark to note where each upright and handrail are
supposed to be installed. A series of 1, 2 or 3 dots on the uprights will match up to the same dots on the outside of the
step section. Attach the uprights so that the dots folds on top of each other as shown in Figure 4.
5. Attach uprights ‘H’ on the open ends of the base ‘A’ using Hex head bolts ‘P’ and Allen key, with the dots facing inwards
as shown in figure 5. (It may require to remove (2) bolts from the upper mounting positions on the center platform to
attach the uprights or position the step sections). HAND TIGHTEN ONLY!
6. Attach uprights (‘I’, ‘K’ & ‘M’ respectively) onto the 6-Step section, by matching up the dots on the upright with step
section using six Hex head bolts ‘Q’ on the bottom of the uprights and two on the top of the 5th step, and four Pan
Head/Philips screw ‘R’ with Flat Washer ‘U’ and Barrel Bolt ‘S’ on the rest as shown in Figure 6.
7. Attach uprights (‘J’ & ‘L’ respectively) onto the 4-Step section using four Hex head bolts ‘Q’ on the bottom of the
uprights and two on the top of the 3rd step, and two Pan Head/Philips screw ‘R’, Flat washer ‘U’ and Barrel Bolt ‘S’ on
the rest as shown in Figure 6.
8. Insert the Barrel Bolt ‘S’ into the straight handrails on the opposite side of the dots as shown in Figure 7.
Figure 3: Base with Step sections
Figure 5: Base with 57 ½” Uprights
Figure 6: Base with all Uprights
Figure 4: Dots on Upright & Steps
Figure 7: Straight Handrails ‘E’
Figure 8: Straight Handrails attached
Dots to match
Cleat
D
C
D
C
H
I
M
K
L
J
Q
E
S

Rev. 102413 aj Page 3of 3©2013 HAUSMANN INDUSTRIES, INC.
9. Attach the straight handrails ‘E’ over the Base ‘A’ on the inside part of the uprights such that Barrel bolts on the
handrails are facing inwards using Pan Head/Philips screw ‘R’ with Flat washer ‘U’ as shown in Figures 8 & 7. At this
point loosely fit the handrail on the uprights.
NOTE: Each Handrail is produced with either a “hook” or a “cup” that are designed to “lock” into each other when
assembled. They also have an inner and outer face, so it is important that they are installed in the correct location.
10. For the corner setup the corner is “locked” together with the “hook” & “cup” fitting as shown in Figure 7 and for the
straight setup the remaining handrails can only be setup one way for correct assembly.
11. Insert the Barrel bolts in each of the medium handrails ‘F’ the same way it was inserted in straight handrails.
12. Attach the Medium handrails ‘F’ on the inside part of the ‘J’ & ‘L’ uprights so that Barrel bolts ‘S’ on the handrails
should be facing inwards using Pan Head/Philips screw ‘R’ with Flat washer ‘U’ as shown in Figures 9.
NOTE: Fit the ‘hook’ or ‘cup’ into the handrail next to it. Once all the handrails are installed, tighten all screws and bolts to
secure the structure.
13. Attach the Long Handrails ‘G’ on the inside part of the ‘I’, ‘K’ & ‘M’ uprights so that Barrel bolts ‘S’ on the handrails
should be facing inwards using Pan Head/Philips screw ‘R’ with Flat washer ‘U’ as shown in Figures 10.
NOTE: Fit the ‘hook’ or ‘cup’ into the handrail next to it. Once all the handrails are installed, tighten all screws and bolts to
secure the structure.
Figure 9: Medium Handrail ‘F’
Figure 10:Long Handrail ‘G’
J
L
F
S
I
K
M
G
S
CAUTION: PREVENTATIVE MAINTENANCE REQUIRED
1. Inspect hex bolts and other mechanical fasteners periodically. Tighten bolts, screws or connections if loose (Tighten until
snug, but do not overtighten). Failure to do so may result in serious injury.
2. Do not use if any loose fasteners are found.
3. Discontinue use of any product that is NOT in proper working order until situation is rectified. Failure to do so may result in
serious injury.