Haute Decor DCCT4501 User manual

4.5’ New Haven Fraser Fir Potted Tree
Pre-Lit w/ 200 ct. Warm White LED Lights
Item # DCCT4501
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
P
ARTS
L
IST
•1 EA. TREE POT
•1 EA. TREE BOTTOM SECTION “A”
•1 EA. TREE TOP SECTION “B”

2 of 4
ASSEMBLY
Carefully remove the contents from the carton and keep the carton for future storage. Be sure to untangle any wires
that may be tangled with other items. (Please DO NOT forcibly remove any contents.)
Step 1: Locate the Tree Pot and place it where you are going to set up the tree – ensure that it is on a level surface and
near a dedicated power source. THIS PRODUCT IS SUITABLE FOR INDOOR AND OUTDOOR USE.
Step 2: Locate the Tree Bottom Section “A” which is tagged with the letter “A”. Remove any plastic protective pole cap
that is on the bottom of the pole (it can be saved and reused for storage if desired). Insert Tree Section “A” into the
Tree Pot. Do not force the pole. It will slide down to its correct position. Make sure the pole is firmly seated and
standing straight.
Step 3: Locate Tree Top Section “B” which is tagged with the letter “B”. Insert it into the top of Tree Section “A”.
Step 4: Connect the plug(s) from each tree section into the section below securely. The light sets each have a male
and/or female end connection with “Please plug in here” tags, so that you can find the corresponding connection
easier. Once all the light sets are connected in the tree, locate the pre-connected power adapter and insert it into a
120-volt power outlet in your home or into a UL approved extension cord or power strip (not included). Tap the foot
pedal to turn the lights on. The tree should now be lit. If some bulbs do not light, please go to the TROUBLESHOOTING
GUIDE FOR LIGHT SETS for steps.
SHAPING
1. Plug in the lights as you are shaping the tree. It is easier to see how the tree looks.
2. Remove any packing strap or other packing material that is around the tree section(s) and allow the branches to fall
into place.
3. Shape by section and layer, starting at the bottom of the tree and working your way up to ensure all branches are
shaped.
4. Slowly pull down each branch to an approximate 90° angle to the floor on the lower sections and about a 45° angle
on the upper sections. While doing so, shape the tips on each individual branch by fanning out the tips to fill any
spaces. Offset the branches from one another to hide the tree’s pole and fill spaces. Continue spreading the tips
until they resemble that of a real tree.
5. After shaping the whole tree, step back and take an overall look. Shift branches to fill any gaps. Your tree is now
ready to decorate and enjoy!
CLEANING &CARE
As you will be using the artificial Christmas tree every year, it is essential to keep it in good condition and clean.
•Dust gently using a soft cloth or fabric duster.
•Do NOT use any chemicals or solvents to clean.
•Handle the light sets gently. Do NOT pull or tug light sets as this may inadvertently loosen the bulb.
•Follow all Storage and Safety Instructions.
STORAGE
1. Unplug the tree from the power source in your home and disconnect the plug connection between the tree
sections.
2. Remove any ornaments and decorations that were added by you and did not come with the tree.
3. After the tree is used outdoors, allow the tree to dry thoroughly prior to packing.
4. Starting with the top, separate each tree section and pot gently, being sure not to roughly handle as it could
cause damage to the parts and could loosen or break bulbs.

3 of 4
5. Compress each tree section by turning it upside down and squeezing the branches together so that it will fit
more easily into the storage box or container. You can also tie a ribbon or cord around the sections to secure
the branches closer together for storage.
6. Place all the parts gently back into the storage box. The box will help prevent the tree from being damaged
should it get bumped in your garage, basement, or other storage location. Tape the box shut to keep out any
dust or insects. When packing up the tree, please ensure that there is no undue strain or stress on the light sets
to ensure they do not get cut, frayed, or damaged.
7. Be sure to store the tree in a cool, dry area free of water and moisture to prevent mold and mildew from
accumulating and a musty odor developing. Exposing your tree to excessive heat or humidity may damage your
tree. DO NOT STORE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE EXCEEDS 100ºF. STORE
THE CARTON FLAT AND NOT UPRIGHT ON ITS SHORT END.
TROUBLESHOOTING GUIDE FOR LIGHT SETS
If your lights are not working, following are some troubleshooting steps to try:
1. Check that the light set plugs are properly connected to your home wall outlet or other power source.
2. Check that there is power to the wall outlet or power source.
3. Check that all the plugs within the tree are securely connected and positioned correctly. Plugs are keyed to fit one
direction only with the flat section of the female plug matching up to the flat section of the male plug.
NOTE: LED bulbs are permanent and cannot be removed from the light sets.
IMPORTANT SAFETY
PLEASE READ AND FOLLOW ALL SAFETY INSTRUCTIONS AND WARNING TAGS INCLUDED WITH THIS TREE.
SAVE FOR FUTURE USE.
THIS TREE IS SAFE FOR INDOOR & OUTDOOR USE.
• When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupter (GFCI).
If you do not have one, contact a qualified electrician for proper installation.
• Do not operate this product if the power cord or plug is damage. Always inspect light sets and electrical cords for
signs of damage or wear. If there are any observable defects, immediately dispose of them and replace it with one
that is in working order.
• Do not immerse the tree or any of its components in water or other liquids. Do not use in a bathroom or within 10
feet of a pool.
•This is an electrical product - not a toy! To avoid risk of fire, burns, personal injury and electric shock, it should not
be played with or placed where small children can reach it.
•Be careful not to overload electrical circuits and do not string more than the manufacturer recommended number
of light sets together.
• This seasonal use product is not intended for permanent installation or use.
• This product is not intended for commercial purposes.
• Do not secure the wiring of this product with staples or nails or place on sharp hooks or nails.
• Do not alter the construction of the wiring in anyway.
• Unplug the product when leaving the house, retiring for the night or if left unattended.
• Do not use this product for anything other than its intended use.
• Do not hang ornaments or other objects from the cord, wire, or light string.
• Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
• Do not cover the product with cloth, paper, or any material not part of the product when in use.
• Do not mount or support strings in a manner that can cut or damage the wire insulation.
• Do not mount or place near gas or electric heaters, fireplaces, candles, or other similar sources of heat.
Female Plug Flat Section
Male Plug Flat Section

4 of 4
• Do not place your tree where it is likely to wobble due to uneven floors or thick carpeting. Place tree on a level,
hard, flat surface.
FCC STATEMENT
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
CANADA ICES-003 STATEMENT
This Class B digital apparatus complies with Industry Canada Standard ICES-003. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
CUSTOMER SERVICE
THANK YOU FOR YOUR PURCHASE!
Comments or questions?
Contact us at 1-877-359-0115
[e-mail]
Haute Decor
PO Box 1594
Allen, TX 75013
Made in China
©2021 Haute Decor