Atdec AD-TVC-70R User manual

AD-TVC-70R Page 1 of 7
Installation Guide
AD-TVC-70R
AV Cart 70 Rotation
COMPONENT CHECKLIST
REQUIRED TOOLS
A
Base (x1)
E
Equipment Shelf
(x1)
F
Shelf Mounting
Bracket (x2)
B
Castor (x4)
C
Base Column (x2)
D
Upper Column (x2)
M
M8x20mm
Screw (x8)
M-A
M5x14mm
Screw (x4)
M-E
M8x50mm
Screw (x4)
M-F
Washer
(x4)
M-G
Small
Spacer (x8)
M-H
Big
Spacer (x8)
M-B
M6x14mm
Screw (x4)
M-C
M6x30mm
Screw (x4)
M-D
M8x30mm
Screw (x4)
S
Cable
Tie (x5)
T
M6 Wrench
(x1)
U
M10 Wrench
(x1)
N
M6x8mm
Screw (x8)
O
M6x12mm
Screw (x16)
P
M6x18mm
Screw (x1)
Q
M8x8mm
Screw (x8)
R
Cable Tie
Holder (x5)
G
Front
Cover (x1)
J
VESA Extension
Adapter Arm (x2)
K
VESA Extension
Adapter Arm (x2)
L
Cable
Cover (x4)
H
Mounting Plate
(x1)
I
Rear Cover
(x1)
V
4mm
Allen Key (x1)
W
5mm
Allen Key (x1)
X
Cable
Clips (x2)
• Phillips Head Screwdriver
CAPACITY
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to assemble this product correctly may cause serious injury/death during or following installation.
! This product should only be installed by professional installers of good mechanical aptitude, who fully understand these
instructions and the consequences of incorrect installation.
! Do not over tighten screws.
! Two person installation is recommended.
! Product not suitable for use outdoors.
! After installation is complete check to verify that AV Cart is secure and safe for use.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA
locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be within the stated range.
Please contact Atdec if you would like further information.
! WARNING! Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control
or toys placed on the cart may encourage a child to climb on the cart and as a result the cart may tip over on to the child.
DISPLAY
0-70kg (0-154lb)
37” - 70”
SHELF
0-5kg (0-11lb)

AD-TVC-70R Page 2 of 7
1. Install the Castors
Lock the brakes on the
castors to avoid any
sudden movements
during installation.
A
B
U
2. Attach the columns to the base
Do not fully tighten the screws M.
C
M
W
Align the column as
shown, making sure that
the cable management
holes and the shorter
legs are on the same side.
WARNING!
! DO NOT ALLOW CHILDREN UNDER 16 TO PLAY WITH OR MOVE CART
! MOVE CART SLOWLY
! USE WITH DISPLAYS HEAVIER THAN SPECIFIED MAY RESULT IN INSTABILITY, TIP OVER AND
RISK OF DEATH OR SERIOUS INJURY
DO NOT PULLNEVER APPLY FORCE AT
TOP
APPLY FORCE ON
NARROW SIDE
PUSH NEAR MIDDLE
DO NOT APPLY MOVING
FORCE ON WIDE SIDE
ONLY ADULTS SHOULD
MOVE THIS CART
KEEP HANDS & OBJECTS
CLEAR OF AREA BELOW
SCREEN WHEN ROTATING
ALLOW SUFFICIENT LOOP
IN CABLE FOR ROTATION
LOCK BRAKES WHEN
STATIONARY

AD-TVC-70R Page 3 of 7
4. Install the front cover and equipment shelf
O
O
M
W
4.1
4.3
4.2
4.4
CAUTION: Fully tighten the
screws Munder the base.
Position both open side
of front cover and shelf
facing backwards.
(The side with shorter legs)
3. Connect the columns
NV
O
D
3.1 Slide shelf mounting
brackets over the
lower columns prior to
connecting the upper
column.
3.3
3.2 Position the cable
management holes
(found on each upper
column leg) facing
inward as shown.
3.4

AD-TVC-70R Page 4 of 7
M-A
M-F
M-F
M-G
M-H
M-C
M-D
M-F
M-B
M-F
M-E
M-G
M-H
Q
W
J
K
J
K
5 . Attach the mounting plate to display
VESA: 200X200/ 300X300/ 350X350/ 400X200/
400X300/ 400X400mm
Too Long Too Short
H
• Select screws to suit display
• Use small or large hole in washer to suit screw
• Use spacers if required to compensate for long fasteners,
or recessed/uneven monitor surfaces
• Use the smallest number of spacers that will work
400mm
350mm
300mm
200mm
200mm
300mm
350mm
400mm
600mm
200mm
400mm
VESA: 600X200/ 600X400
M-A
M-F
M-B
M-F
M-G
M-H
M-E
M-F
M-F
M-G
M-H
M-C
M-D

AD-TVC-70R Page 5 of 7
W
M
0°
5°
Tilt
8. Set screen rotation
8.1 Increase or reduce friction of screen
rotation by tightening or loosening nuts.
8.4 (Option) Fix the screen in
portrait by fastening screw Pon
left hand side.
8.2
8.3 (Option) Fix the screen in
landscape by fastening screw
Pat the top.
T
P
P
7. Set the tilt angle of the display
M
Default Position (0°) Tilted Position (5°)
6. Mount display onto screws
W M
10mm
(3/8”)

AD-TVC-70R Page 6 of 7
9. Cable routing options
9.1 Cables can be routed down the inside or outside of column.
9.2
9.4
9.3
R
S
S
CAUTION: Allow sufcient loop
in cables for screen rotation.

AD-TVC-70R Page 7 of 7
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20210413A
11. Attach the rear cover
Maintenance
• Tighten fasteners and check if the cart is
secure and safe to use at regular intervals
(at least every three months.)
• Please contact your distributor if you
have any questions.
O
O
10. Attach cable covers
OR OR
10.1 Remove tabs as needed to fit wires.