HCP QR201 User manual

QR201
2D barcode scanner
User manual
Dear customer, thank you for buying one of the product of HCP company.
Before first use, read this notice carefully and if you have any doubts, please contact our authorized
service.
Sincerely,
HCP d.o.o.

2 od 10
About device
QR201 is a 2D barcode scanner with barcode module of reputable, worldwide known manufacturer
Opticon. It supports standard 1D and 2D barcodes.
1. Package contents
1.
QR201 barcode scanner (USB version QR201U)
2.
USB cable (USB type A - RJ45)
3.
User manual
4.
CD with drivers
2. Technical characteristics
3. Supported 1D and 2D barcode types
1D:
JAN/UPC/EAN incl. add on, Codabar/NW-7, Code 11, Code 39, Code 93, Code 128, GS1-128 (EAN-128),
GS1 DataBar (RSS), IATA, Industrial 2of5, Interleaved 2of5, ISBN, ISMN, ISSN, Matrix 2of5, MSI/Plessey,
S-code, Telepen, Tri-Optic, UK/Plessey.
Postal Code:
Chinese post, intelligent Mail Barcode, Korean postal authority code, POSTNET.
2D:
Aztec code, Aztec Runes, Chinese Sensible code, Codablock F, Composite codes, Data Matrix
(ECC200/EC0-140), Maxi Code (mode 2~5), MicroPDF417, Micro QR code, PDF417, QR code.
Communication interface
USB (COM & HID)
Scan speed
60 fps
Light source type
Green LED + Red LED
Scan mode
CMOS sensor 752x480
Reading resolution
0.127mm
Scan angle
-45°up to 0, 0 up to +45°
Power supply
5V
Working current
max 300mA
Working temperature
-20°up to 60°

3 od 10
4. Review device
5. Connect the communication cable

4 od 10
6. PC connectivity
7. Tips for scanning barcode
It is recommended that the barcode symbols scanned under angle less than or greather than 90˚. Also,
avoing scanning too close.

5 od 10
8. Adjust the barcode scanner
NOTE
For advanced settings QR201 used applications “UniversalMenuTool2D”.
QR201 can connect to PC as a HID device (as a standard PC keyboard without installing drivers)
or as open COM port on the computer for which it is necessary to install the appropriate drivers.
Drivers are on CD that goes with the device or you can downloaded it from website www.hcp.rs or
from forum www.hcp.rs/forum.
If you want to QR201 connect to the computer on open COM port, you need to scann 2D barcode
bellow which writes “USB-COM“ (it is necessary install drivers from CD) and if you want to QR201
connect as a HID device, you need to scann 2D barcode bellow which writes “USB-HID“.

6 od 10
Adjustment procedure barcode scanner:
1. scan the barcode symbol “SET”
2. scan the desired setting
3. scan the barcode symbol “END”
8.1. Automatic scanning
QR201 has the ability to work in automatic mode when we put barcode scanning product, barcode
scan automatically scans without pressing buttons.
Activating this mode is done by scanning the barcode in the table below.
The order of scanning for turn on automatic mode is:
1. scan the barcode“SET“
2. scan the barcode“Turn on automatic scan“
3. scan the barcode“END“
The order of scanning for turn off automatic mode is:
1. scann the barcode “SET“
2. scan the barcode “Turn off automatic scan“
3. scan the barcode “END“
SET
Turn on
automatic
scan
Turn off
automatic
scan
END

7 od 10
8.1 Setting piezo speaker
SET
Turn off
Turn on
Volume: quiet
Volume:
medium
Volume: high
Volume: loud
END

8 od 10
8.2 Adjusting the light indication
SET
Turn off
Turn on
Duration:
0,2s
END

9 od 10
10. Pin layout
USB type A –RJ45
Pin
RJ45 on QR201U
1
-
2
-
3
-
4
-
5
GND
6
GND
7
USB_D+
8
USB_D-
9
Vcc_USB
10
-
Pin
USB type A
1
Vcc_USB
2
USB_D-
3
USB_D+
4
GND

10 od 10
NOTE:
Only use the cables that come with the device QR201!
NOTE:
In case of any failure you should contact the nearest authorized service center. HCP d.o.o is not
responsible for any damage caused by improper use of the device, (physical damage of the monitor housing)
using spare parts that are not original or interventions by unauthorized persons. It is forbidden and dangerous
to inject any kind of things and liquid into the device.
HCP d.o.o reserves the right to make changes in specifications and other information contained
in this document without notice, and users should be consulted in all cases HCP to determine whether
any such changes made. HCP shall not be liable for technical or editorial errors or omissions contained
in this document: nor for incidental or consequential damages incurred when using this guide. This
document contains information on safety that is protected by copyright. All Rights Reserved. No part
of this document may be photocopied, reproduced or translated into another language without the
prior written consent of HCP.
For more information about products visit website www.hcp.rs
Additional documentation about the devices can be found on our forum www.hcp.rs/forum
For technical assistance, contact us at [email protected]s