HEADRUSH HRB 5035 User manual
Use the included charging cable to fully charge the case before rst
use. It will take approximately 1.5 hours to fully charge.
The LED will ash during charging, and remain solid when charging
is complete.
Red LED ON indicates power level is lower than 25%.
Yellow LED ON indicates power level is between 25%~50%.
Green LED ON indicates power level is between 50%~75%.
Blue LED ON indicates power level is between 75%~100%.
CHARGING THE EARBUDS
1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The
LED indicator will be solid blue/green/yellow/red (depending on the
charge case’s power level) when the earpbuds are charging and will
turn OFF when fully charged.
NOTE: Please make sure the charging case has enough power to
charge the earbuds. Prior to rst use, remove the plastic battery
isolator tabs located on the earbud charging points. When the earbuds
are paired to an Android™ or iOS device, the remaining earbud battery
power will show on the device display.
PAIRING
1. Open the lid of the charging case. The earbuds will automatically
turn ON. The LED will ash white and blue and the earbuds will
beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth�device list to pair the
earbuds automatically.
3. The earbuds will beep when Bluetooth�is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and
connect to your device when removed from the charging case,
provided both earbuds and your Bluetooth�are ON and
within range.
5. The earbuds will automatically turn OFF after 5 minutes if no
connection is established.
FIT
We recommend that you try each ear tip (small, medium and large),
then perform a sound check and choose the combination that provides
the best sound experience.
RESET
When the “L” and “R” earbuds cannot connect to each other, you will
need to reset the earbuds and clear the paired memory:
1. Remove HRB “5035” from your list of Bluetooth�devices.
2. Turn off Bluetooth�in your device settings.
3. Remove the earbuds from the charging case and turn them OFF.
Press and hold both MFB buttons for 8 seconds. The LED indicator
will be white, then blue and you will hear a beep when the earbuds
have been reset.
4. Return the earbuds to the charging case, close and then reopen the
lid. The earbuds will automatically turn ON and pair with each other.
You will hear a beep and the LED on the one earbud will ash blue
and white, the LED on the second earbud will ash blue.
5. Turn on Bluetooth®in your device settings, Select “HRB 5035” to pair.
Instruction Manual 8093128 OPERATING INSTRUCTIONS
Prior to rst use, remove the plastic battery isolator tabs located
on the earbud charging points.
TO DO THIS
Power ON Remove the earbuds from the charging case or
press and hold both MFB buttons for 2 seconds.
Power OFF Return the earbuds to the charging case. Alternatively,
when music is paused, you can press and hold either
MFB button for 4 seconds. If music is playing, this
function will not work.
Play Music Press either MFB button.
Pause Music Press either MFB button.
Next song Press the right MFB button twice.
Previous song Press the left MFB button twice.
Activate/Stop Voice Assistant Press either MFB button three times.
Volume up Press and hold the right MFB button for 2 seconds.
Volume down Press and hold the left MFB button for 2 seconds.
Answer a call Press either MFB button.
End a call Press either MFB button.
Reject an incoming call Press and hold either MFB button.
NOTE: The function compatibility may vary among different
smartphones or devices. Not all functions are available on all devices.
CHARGING THE CASE
OPERATION
• While playing music, press either MFB button to pause,
press again to resume
• Quickly press the right MFB twice for the next song, quickly press
the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an
incoming call. Press either MFB button once to answer the call,
press and hold to reject the call
WARNING!
• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over
extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you
should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the
earbuds may cause clicks which at high volume settings, may affect
your hearing. Therefore, always set the volume control to minimum
before switching between different sources (tuner, turntable, CD
player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard.
This product is not intended for use by small children and should be
kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the
earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose
of batteries in re to prevent an explosion
TROUBLESHOOTING
No sound
• Please check the volume on your audio device to make sure it is
outputting sound
Connection Problems
• Please return the earbuds to the case and then remove them again
if there are any connection issues
• Refer to the cleared paired memory and reset section
INTRODUCTION
Thank you for purchasing the HRB 5035 true wireless earbuds.
In order to maximize your listening experience please read the
following instructions.
WHAT’S INCLUDED
• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual
1
2
3
Charging pins
Charging case LED indicator
USB-C charging port
MFB (Multi-function button)
Earbud LED indicator
Charging contact point
Ear tip
The earbuds are not tting comfortably
• Please switch out the earbud tips to a different size to find the
appropriate fit
Improve the Sound
• Sound can sometimes be improved by moving to a larger eartip
size. The eartips still need to fit comfortably in your ear
CLEANING
Your earbuds may require periodic cleaning. Use a dry, soft, lint-free
cloth to clean your earbuds. To clean the microphone and speaker
mesh, use a dry cotton swab.
IMPORTANT SAFETY INFORMATION
CAUTIONS
• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product
SPECIFICATIONS
Bluetooth®version: v5.1
Bluetooth® proles*: HSP; HFP; A2DP; AVRCP;
APTX
EARBUDS
Wireless range: 10m (32ft.)
Playback time: approx. 11 hours**
Standby time: approx. 60 hours
Rated input: DC 5V/70mA
Driver diameter: 6mm
Sensitivity: 90db±3db
Frequency response: 20Hz~20kHz
Impedance: 16 Ohms±15%
Battery: Polymer Lithium
Battery capacity: 70mAh
Earbuds charging time: approx. 1.5 Hours
IP rating: IPX4
Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.
Please
Recycle
4
5
CHARGING CASE
Rated input: DC 5V, 500mA
Output: DC 5V, 300mA
Battery Capacity: 400mAh
Case charging time: Approx. 1.5 hours
Fully powered case: Provides up to 1.5 charges
*A2DP=Advanced Audio distribution Prole, AVRCP=Audio Video
Remote Control Prole, HSP=Handset Prole, HFP=Handfree Prole.
**Approximate playback time, battery life depends on individual use
and may be more or less than specied.
***Standby, Bluetooth® connected, power ON, no music playing.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth®SIG,
Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other
trademarks and trade names are those of their respective owners.
INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is
Subject to the following two conditions:
• This device may not cause interference, and this device must accept any
interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of Industry Canada
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of Industry Canada.
ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired
operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)
The Source warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available)
without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-
ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any
legal rights other than those set out above, you may have additional statutory rights which will vary under the
laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.
THE SOURCE - WARRANTY
1
2
3
4
5
6
7
6
7
0~25% 25%~50% 50%~75% 75%~100%
TRUE WIRELESS
EARBUDS
HRB 5035
Additional large and small earbud tips
included (medium tips installed on earbuds).
Use the included charging cable to fully charge the case before rst
use. It will take approximately 1.5 hours to fully charge.
The LED will ash during charging, and remain solid when charging
is complete.
Red LED ON indicates power level is lower than 25%.
Yellow LED ON indicates power level is between 25%~50%.
Green LED ON indicates power level is between 50%~75%.
Blue LED ON indicates power level is between 75%~100%.
CHARGING THE EARBUDS
1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The
LED indicator will be solid blue/green/yellow/red (depending on the
charge case’s power level) when the earpbuds are charging and will
turn OFF when fully charged.
NOTE: Please make sure the charging case has enough power to
charge the earbuds. Prior to rst use, remove the plastic battery
isolator tabs located on the earbud charging points. When the earbuds
are paired to an Android™ or iOS device, the remaining earbud battery
power will show on the device display.
PAIRING
1. Open the lid of the charging case. The earbuds will automatically
turn ON. The LED will ash white and blue and the earbuds will
beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth�device list to pair the
earbuds automatically.
3. The earbuds will beep when Bluetooth�is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and
connect to your device when removed from the charging case,
provided both earbuds and your Bluetooth�are ON and
within range.
5. The earbuds will automatically turn OFF after 5 minutes if no
connection is established.
FIT
We recommend that you try each ear tip (small, medium and large),
then perform a sound check and choose the combination that provides
the best sound experience.
RESET
When the “L” and “R” earbuds cannot connect to each other, you will
need to reset the earbuds and clear the paired memory:
1. Remove HRB “5035” from your list of Bluetooth�devices.
2. Turn off Bluetooth�in your device settings.
3. Remove the earbuds from the charging case and turn them OFF.
Press and hold both MFB buttons for 8 seconds. The LED indicator
will be white, then blue and you will hear a beep when the earbuds
have been reset.
4. Return the earbuds to the charging case, close and then reopen the
lid. The earbuds will automatically turn ON and pair with each other.
You will hear a beep and the LED on the one earbud will ash blue
and white, the LED on the second earbud will ash blue.
5. Turn on Bluetooth®in your device settings, Select “HRB 5035” to pair.
Instruction Manual 8093128 OPERATING INSTRUCTIONS
Prior to rst use, remove the plastic battery isolator tabs located
on the earbud charging points.
TO DO THIS
Power ON Remove the earbuds from the charging case or
press and hold both MFB buttons for 2 seconds.
Power OFF Return the earbuds to the charging case. Alternatively,
when music is paused, you can press and hold either
MFB button for 4 seconds. If music is playing, this
function will not work.
Play Music Press either MFB button.
Pause Music Press either MFB button.
Next song Press the right MFB button twice.
Previous song Press the left MFB button twice.
Activate/Stop Voice Assistant Press either MFB button three times.
Volume up Press and hold the right MFB button for 2 seconds.
Volume down Press and hold the left MFB button for 2 seconds.
Answer a call Press either MFB button.
End a call Press either MFB button.
Reject an incoming call Press and hold either MFB button.
NOTE: The function compatibility may vary among different
smartphones or devices. Not all functions are available on all devices.
CHARGING THE CASE
OPERATION
• While playing music, press either MFB button to pause,
press again to resume
• Quickly press the right MFB twice for the next song, quickly press
the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an
incoming call. Press either MFB button once to answer the call,
press and hold to reject the call
WARNING!
• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over
extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you
should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the
earbuds may cause clicks which at high volume settings, may affect
your hearing. Therefore, always set the volume control to minimum
before switching between different sources (tuner, turntable, CD
player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard.
This product is not intended for use by small children and should be
kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the
earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose
of batteries in re to prevent an explosion
TROUBLESHOOTING
No sound
• Please check the volume on your audio device to make sure it is
outputting sound
Connection Problems
• Please return the earbuds to the case and then remove them again
if there are any connection issues
• Refer to the cleared paired memory and reset section
INTRODUCTION
Thank you for purchasing the HRB 5035 true wireless earbuds.
In order to maximize your listening experience please read the
following instructions.
WHAT’S INCLUDED
• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual
1
2
3
Charging pins
Charging case LED indicator
USB-C charging port
MFB (Multi-function button)
Earbud LED indicator
Charging contact point
Ear tip
The earbuds are not tting comfortably
• Please switch out the earbud tips to a different size to find the
appropriate fit
Improve the Sound
• Sound can sometimes be improved by moving to a larger eartip
size. The eartips still need to fit comfortably in your ear
CLEANING
Your earbuds may require periodic cleaning. Use a dry, soft, lint-free
cloth to clean your earbuds. To clean the microphone and speaker
mesh, use a dry cotton swab.
IMPORTANT SAFETY INFORMATION
CAUTIONS
• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product
SPECIFICATIONS
Bluetooth®version: v5.1
Bluetooth® proles*: HSP; HFP; A2DP; AVRCP;
APTX
EARBUDS
Wireless range: 10m (32ft.)
Playback time: approx. 11 hours**
Standby time: approx. 60 hours
Rated input: DC 5V/70mA
Driver diameter: 6mm
Sensitivity: 90db±3db
Frequency response: 20Hz~20kHz
Impedance: 16 Ohms±15%
Battery: Polymer Lithium
Battery capacity: 70mAh
Earbuds charging time: approx. 1.5 Hours
IP rating: IPX4
Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.
Please
Recycle
4
5
CHARGING CASE
Rated input: DC 5V, 500mA
Output: DC 5V, 300mA
Battery Capacity: 400mAh
Case charging time: Approx. 1.5 hours
Fully powered case: Provides up to 1.5 charges
*A2DP=Advanced Audio distribution Prole, AVRCP=Audio Video
Remote Control Prole, HSP=Handset Prole, HFP=Handfree Prole.
**Approximate playback time, battery life depends on individual use
and may be more or less than specied.
***Standby, Bluetooth® connected, power ON, no music playing.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth®SIG,
Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other
trademarks and trade names are those of their respective owners.
INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is
Subject to the following two conditions:
• This device may not cause interference, and this device must accept any
interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of Industry Canada
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of Industry Canada.
ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired
operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)
The Source warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available)
without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-
ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any
legal rights other than those set out above, you may have additional statutory rights which will vary under the
laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.
THE SOURCE - WARRANTY
1
2
3
4
5
6
7
6
7
0~25% 25%~50% 50%~75% 75%~100%
TRUE WIRELESS
EARBUDS
HRB 5035
Additional large and small earbud tips
included (medium tips installed on earbuds).
Use the included charging cable to fully charge the case before rst
use. It will take approximately 1.5 hours to fully charge.
The LED will ash during charging, and remain solid when charging
is complete.
Red LED ON indicates power level is lower than 25%.
Yellow LED ON indicates power level is between 25%~50%.
Green LED ON indicates power level is between 50%~75%.
Blue LED ON indicates power level is between 75%~100%.
CHARGING THE EARBUDS
1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The
LED indicator will be solid blue/green/yellow/red (depending on the
charge case’s power level) when the earpbuds are charging and will
turn OFF when fully charged.
NOTE: Please make sure the charging case has enough power to
charge the earbuds. Prior to rst use, remove the plastic battery
isolator tabs located on the earbud charging points. When the earbuds
are paired to an Android™ or iOS device, the remaining earbud battery
power will show on the device display.
PAIRING
1. Open the lid of the charging case. The earbuds will automatically
turn ON. The LED will ash white and blue and the earbuds will
beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth�device list to pair the
earbuds automatically.
3. The earbuds will beep when Bluetooth�is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and
connect to your device when removed from the charging case,
provided both earbuds and your Bluetooth�are ON and
within range.
5. The earbuds will automatically turn OFF after 5 minutes if no
connection is established.
FIT
We recommend that you try each ear tip (small, medium and large),
then perform a sound check and choose the combination that provides
the best sound experience.
RESET
When the “L” and “R” earbuds cannot connect to each other, you will
need to reset the earbuds and clear the paired memory:
1. Remove HRB “5035” from your list of Bluetooth�devices.
2. Turn off Bluetooth�in your device settings.
3. Remove the earbuds from the charging case and turn them OFF.
Press and hold both MFB buttons for 8 seconds. The LED indicator
will be white, then blue and you will hear a beep when the earbuds
have been reset.
4. Return the earbuds to the charging case, close and then reopen the
lid. The earbuds will automatically turn ON and pair with each other.
You will hear a beep and the LED on the one earbud will ash blue
and white, the LED on the second earbud will ash blue.
5. Turn on Bluetooth®in your device settings, Select “HRB 5035” to pair.
Instruction Manual 8093128 OPERATING INSTRUCTIONS
Prior to rst use, remove the plastic battery isolator tabs located
on the earbud charging points.
TO DO THIS
Power ON Remove the earbuds from the charging case or
press and hold both MFB buttons for 2 seconds.
Power OFF Return the earbuds to the charging case. Alternatively,
when music is paused, you can press and hold either
MFB button for 4 seconds. If music is playing, this
function will not work.
Play Music Press either MFB button.
Pause Music Press either MFB button.
Next song Press the right MFB button twice.
Previous song Press the left MFB button twice.
Activate/Stop Voice Assistant Press either MFB button three times.
Volume up Press and hold the right MFB button for 2 seconds.
Volume down Press and hold the left MFB button for 2 seconds.
Answer a call Press either MFB button.
End a call Press either MFB button.
Reject an incoming call Press and hold either MFB button.
NOTE: The function compatibility may vary among different
smartphones or devices. Not all functions are available on all devices.
CHARGING THE CASE
OPERATION
• While playing music, press either MFB button to pause,
press again to resume
• Quickly press the right MFB twice for the next song, quickly press
the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an
incoming call. Press either MFB button once to answer the call,
press and hold to reject the call
WARNING!
• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over
extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you
should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the
earbuds may cause clicks which at high volume settings, may affect
your hearing. Therefore, always set the volume control to minimum
before switching between different sources (tuner, turntable, CD
player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard.
This product is not intended for use by small children and should be
kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the
earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose
of batteries in re to prevent an explosion
TROUBLESHOOTING
No sound
• Please check the volume on your audio device to make sure it is
outputting sound
Connection Problems
• Please return the earbuds to the case and then remove them again
if there are any connection issues
• Refer to the cleared paired memory and reset section
INTRODUCTION
Thank you for purchasing the HRB 5035 true wireless earbuds.
In order to maximize your listening experience please read the
following instructions.
WHAT’S INCLUDED
• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual
1
2
3
Charging pins
Charging case LED indicator
USB-C charging port
MFB (Multi-function button)
Earbud LED indicator
Charging contact point
Ear tip
The earbuds are not tting comfortably
• Please switch out the earbud tips to a different size to find the
appropriate fit
Improve the Sound
• Sound can sometimes be improved by moving to a larger eartip
size. The eartips still need to fit comfortably in your ear
CLEANING
Your earbuds may require periodic cleaning. Use a dry, soft, lint-free
cloth to clean your earbuds. To clean the microphone and speaker
mesh, use a dry cotton swab.
IMPORTANT SAFETY INFORMATION
CAUTIONS
• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product
SPECIFICATIONS
Bluetooth®version: v5.1
Bluetooth® proles*: HSP; HFP; A2DP; AVRCP;
APTX
EARBUDS
Wireless range: 10m (32ft.)
Playback time: approx. 11 hours**
Standby time: approx. 60 hours
Rated input: DC 5V/70mA
Driver diameter: 6mm
Sensitivity: 90db±3db
Frequency response: 20Hz~20kHz
Impedance: 16 Ohms±15%
Battery: Polymer Lithium
Battery capacity: 70mAh
Earbuds charging time: approx. 1.5 Hours
IP rating: IPX4
Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.
Please
Recycle
4
5
CHARGING CASE
Rated input: DC 5V, 500mA
Output: DC 5V, 300mA
Battery Capacity: 400mAh
Case charging time: Approx. 1.5 hours
Fully powered case: Provides up to 1.5 charges
*A2DP=Advanced Audio distribution Prole, AVRCP=Audio Video
Remote Control Prole, HSP=Handset Prole, HFP=Handfree Prole.
**Approximate playback time, battery life depends on individual use
and may be more or less than specied.
***Standby, Bluetooth® connected, power ON, no music playing.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth®SIG,
Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other
trademarks and trade names are those of their respective owners.
INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is
Subject to the following two conditions:
• This device may not cause interference, and this device must accept any
interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of Industry Canada
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of Industry Canada.
ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired
operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)
The Source warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available)
without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-
ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any
legal rights other than those set out above, you may have additional statutory rights which will vary under the
laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.
THE SOURCE - WARRANTY
1
2
3
4
5
6
7
6
7
0~25% 25%~50% 50%~75% 75%~100%
TRUE WIRELESS
EARBUDS
HRB 5035
Additional large and small earbud tips
included (medium tips installed on earbuds).
Use the included charging cable to fully charge the case before rst
use. It will take approximately 1.5 hours to fully charge.
The LED will ash during charging, and remain solid when charging
is complete.
Red LED ON indicates power level is lower than 25%.
Yellow LED ON indicates power level is between 25%~50%.
Green LED ON indicates power level is between 50%~75%.
Blue LED ON indicates power level is between 75%~100%.
CHARGING THE EARBUDS
1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The
LED indicator will be solid blue/green/yellow/red (depending on the
charge case’s power level) when the earpbuds are charging and will
turn OFF when fully charged.
NOTE: Please make sure the charging case has enough power to
charge the earbuds. Prior to rst use, remove the plastic battery
isolator tabs located on the earbud charging points. When the earbuds
are paired to an Android™ or iOS device, the remaining earbud battery
power will show on the device display.
PAIRING
1. Open the lid of the charging case. The earbuds will automatically
turn ON. The LED will ash white and blue and the earbuds will
beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth�device list to pair the
earbuds automatically.
3. The earbuds will beep when Bluetooth�is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and
connect to your device when removed from the charging case,
provided both earbuds and your Bluetooth�are ON and
within range.
5. The earbuds will automatically turn OFF after 5 minutes if no
connection is established.
FIT
We recommend that you try each ear tip (small, medium and large),
then perform a sound check and choose the combination that provides
the best sound experience.
RESET
When the “L” and “R” earbuds cannot connect to each other, you will
need to reset the earbuds and clear the paired memory:
1. Remove HRB “5035” from your list of Bluetooth�devices.
2. Turn off Bluetooth�in your device settings.
3. Remove the earbuds from the charging case and turn them OFF.
Press and hold both MFB buttons for 8 seconds. The LED indicator
will be white, then blue and you will hear a beep when the earbuds
have been reset.
4. Return the earbuds to the charging case, close and then reopen the
lid. The earbuds will automatically turn ON and pair with each other.
You will hear a beep and the LED on the one earbud will ash blue
and white, the LED on the second earbud will ash blue.
5. Turn on Bluetooth®in your device settings, Select “HRB 5035” to pair.
Instruction Manual 8093128 OPERATING INSTRUCTIONS
Prior to rst use, remove the plastic battery isolator tabs located
on the earbud charging points.
TO DO THIS
Power ON Remove the earbuds from the charging case or
press and hold both MFB buttons for 2 seconds.
Power OFF Return the earbuds to the charging case. Alternatively,
when music is paused, you can press and hold either
MFB button for 4 seconds. If music is playing, this
function will not work.
Play Music Press either MFB button.
Pause Music Press either MFB button.
Next song Press the right MFB button twice.
Previous song Press the left MFB button twice.
Activate/Stop Voice Assistant Press either MFB button three times.
Volume up Press and hold the right MFB button for 2 seconds.
Volume down Press and hold the left MFB button for 2 seconds.
Answer a call Press either MFB button.
End a call Press either MFB button.
Reject an incoming call Press and hold either MFB button.
NOTE: The function compatibility may vary among different
smartphones or devices. Not all functions are available on all devices.
CHARGING THE CASE
OPERATION
• While playing music, press either MFB button to pause,
press again to resume
• Quickly press the right MFB twice for the next song, quickly press
the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an
incoming call. Press either MFB button once to answer the call,
press and hold to reject the call
WARNING!
• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over
extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you
should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the
earbuds may cause clicks which at high volume settings, may affect
your hearing. Therefore, always set the volume control to minimum
before switching between different sources (tuner, turntable, CD
player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard.
This product is not intended for use by small children and should be
kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the
earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose
of batteries in re to prevent an explosion
TROUBLESHOOTING
No sound
• Please check the volume on your audio device to make sure it is
outputting sound
Connection Problems
• Please return the earbuds to the case and then remove them again
if there are any connection issues
• Refer to the cleared paired memory and reset section
INTRODUCTION
Thank you for purchasing the HRB 5035 true wireless earbuds.
In order to maximize your listening experience please read the
following instructions.
WHAT’S INCLUDED
• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual
1
2
3
Charging pins
Charging case LED indicator
USB-C charging port
MFB (Multi-function button)
Earbud LED indicator
Charging contact point
Ear tip
The earbuds are not tting comfortably
• Please switch out the earbud tips to a different size to find the
appropriate fit
Improve the Sound
• Sound can sometimes be improved by moving to a larger eartip
size. The eartips still need to fit comfortably in your ear
CLEANING
Your earbuds may require periodic cleaning. Use a dry, soft, lint-free
cloth to clean your earbuds. To clean the microphone and speaker
mesh, use a dry cotton swab.
IMPORTANT SAFETY INFORMATION
CAUTIONS
• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product
SPECIFICATIONS
Bluetooth®version: v5.1
Bluetooth® proles*: HSP; HFP; A2DP; AVRCP;
APTX
EARBUDS
Wireless range: 10m (32ft.)
Playback time: approx. 11 hours**
Standby time: approx. 60 hours
Rated input: DC 5V/70mA
Driver diameter: 6mm
Sensitivity: 90db±3db
Frequency response: 20Hz~20kHz
Impedance: 16 Ohms±15%
Battery: Polymer Lithium
Battery capacity: 70mAh
Earbuds charging time: approx. 1.5 Hours
IP rating: IPX4
Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.
Please
Recycle
4
5
CHARGING CASE
Rated input: DC 5V, 500mA
Output: DC 5V, 300mA
Battery Capacity: 400mAh
Case charging time: Approx. 1.5 hours
Fully powered case: Provides up to 1.5 charges
*A2DP=Advanced Audio distribution Prole, AVRCP=Audio Video
Remote Control Prole, HSP=Handset Prole, HFP=Handfree Prole.
**Approximate playback time, battery life depends on individual use
and may be more or less than specied.
***Standby, Bluetooth® connected, power ON, no music playing.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth®SIG,
Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other
trademarks and trade names are those of their respective owners.
INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is
Subject to the following two conditions:
• This device may not cause interference, and this device must accept any
interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of Industry Canada
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of Industry Canada.
ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired
operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)
The Source warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available)
without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-
ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any
legal rights other than those set out above, you may have additional statutory rights which will vary under the
laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.
THE SOURCE - WARRANTY
1
2
3
4
5
6
7
6
7
0~25% 25%~50% 50%~75% 75%~100%
TRUE WIRELESS
EARBUDS
HRB 5035
Additional large and small earbud tips
included (medium tips installed on earbuds).
Use the included charging cable to fully charge the case before rst
use. It will take approximately 1.5 hours to fully charge.
The LED will ash during charging, and remain solid when charging
is complete.
Red LED ON indicates power level is lower than 25%.
Yellow LED ON indicates power level is between 25%~50%.
Green LED ON indicates power level is between 50%~75%.
Blue LED ON indicates power level is between 75%~100%.
CHARGING THE EARBUDS
1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The
LED indicator will be solid blue/green/yellow/red (depending on the
charge case’s power level) when the earpbuds are charging and will
turn OFF when fully charged.
NOTE: Please make sure the charging case has enough power to
charge the earbuds. Prior to rst use, remove the plastic battery
isolator tabs located on the earbud charging points. When the earbuds
are paired to an Android™ or iOS device, the remaining earbud battery
power will show on the device display.
PAIRING
1. Open the lid of the charging case. The earbuds will automatically
turn ON. The LED will ash white and blue and the earbuds will
beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth�device list to pair the
earbuds automatically.
3. The earbuds will beep when Bluetooth�is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and
connect to your device when removed from the charging case,
provided both earbuds and your Bluetooth�are ON and
within range.
5. The earbuds will automatically turn OFF after 5 minutes if no
connection is established.
FIT
We recommend that you try each ear tip (small, medium and large),
then perform a sound check and choose the combination that provides
the best sound experience.
RESET
When the “L” and “R” earbuds cannot connect to each other, you will
need to reset the earbuds and clear the paired memory:
1. Remove HRB “5035” from your list of Bluetooth�devices.
2. Turn off Bluetooth�in your device settings.
3. Remove the earbuds from the charging case and turn them OFF.
Press and hold both MFB buttons for 8 seconds. The LED indicator
will be white, then blue and you will hear a beep when the earbuds
have been reset.
4. Return the earbuds to the charging case, close and then reopen the
lid. The earbuds will automatically turn ON and pair with each other.
You will hear a beep and the LED on the one earbud will ash blue
and white, the LED on the second earbud will ash blue.
5. Turn on Bluetooth®in your device settings, Select “HRB 5035” to pair.
Instruction Manual 8093128 OPERATING INSTRUCTIONS
Prior to rst use, remove the plastic battery isolator tabs located
on the earbud charging points.
TO DO THIS
Power ON Remove the earbuds from the charging case or
press and hold both MFB buttons for 2 seconds.
Power OFF Return the earbuds to the charging case. Alternatively,
when music is paused, you can press and hold either
MFB button for 4 seconds. If music is playing, this
function will not work.
Play Music Press either MFB button.
Pause Music Press either MFB button.
Next song Press the right MFB button twice.
Previous song Press the left MFB button twice.
Activate/Stop Voice Assistant Press either MFB button three times.
Volume up Press and hold the right MFB button for 2 seconds.
Volume down Press and hold the left MFB button for 2 seconds.
Answer a call Press either MFB button.
End a call Press either MFB button.
Reject an incoming call Press and hold either MFB button.
NOTE: The function compatibility may vary among different
smartphones or devices. Not all functions are available on all devices.
CHARGING THE CASE
OPERATION
• While playing music, press either MFB button to pause,
press again to resume
• Quickly press the right MFB twice for the next song, quickly press
the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an
incoming call. Press either MFB button once to answer the call,
press and hold to reject the call
WARNING!
• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over
extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you
should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the
earbuds may cause clicks which at high volume settings, may affect
your hearing. Therefore, always set the volume control to minimum
before switching between different sources (tuner, turntable, CD
player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard.
This product is not intended for use by small children and should be
kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the
earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose
of batteries in re to prevent an explosion
TROUBLESHOOTING
No sound
• Please check the volume on your audio device to make sure it is
outputting sound
Connection Problems
• Please return the earbuds to the case and then remove them again
if there are any connection issues
• Refer to the cleared paired memory and reset section
INTRODUCTION
Thank you for purchasing the HRB 5035 true wireless earbuds.
In order to maximize your listening experience please read the
following instructions.
WHAT’S INCLUDED
• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual
1
2
3
Charging pins
Charging case LED indicator
USB-C charging port
MFB (Multi-function button)
Earbud LED indicator
Charging contact point
Ear tip
The earbuds are not tting comfortably
• Please switch out the earbud tips to a different size to find the
appropriate fit
Improve the Sound
• Sound can sometimes be improved by moving to a larger eartip
size. The eartips still need to fit comfortably in your ear
CLEANING
Your earbuds may require periodic cleaning. Use a dry, soft, lint-free
cloth to clean your earbuds. To clean the microphone and speaker
mesh, use a dry cotton swab.
IMPORTANT SAFETY INFORMATION
CAUTIONS
• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product
SPECIFICATIONS
Bluetooth®version: v5.1
Bluetooth® proles*: HSP; HFP; A2DP; AVRCP;
APTX
EARBUDS
Wireless range: 10m (32ft.)
Playback time: approx. 11 hours**
Standby time: approx. 60 hours
Rated input: DC 5V/70mA
Driver diameter: 6mm
Sensitivity: 90db±3db
Frequency response: 20Hz~20kHz
Impedance: 16 Ohms±15%
Battery: Polymer Lithium
Battery capacity: 70mAh
Earbuds charging time: approx. 1.5 Hours
IP rating: IPX4
Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.
Please
Recycle
4
5
CHARGING CASE
Rated input: DC 5V, 500mA
Output: DC 5V, 300mA
Battery Capacity: 400mAh
Case charging time: Approx. 1.5 hours
Fully powered case: Provides up to 1.5 charges
*A2DP=Advanced Audio distribution Prole, AVRCP=Audio Video
Remote Control Prole, HSP=Handset Prole, HFP=Handfree Prole.
**Approximate playback time, battery life depends on individual use
and may be more or less than specied.
***Standby, Bluetooth® connected, power ON, no music playing.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth®SIG,
Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other
trademarks and trade names are those of their respective owners.
INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is
Subject to the following two conditions:
• This device may not cause interference, and this device must accept any
interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of Industry Canada
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of Industry Canada.
ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired
operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)
The Source warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available)
without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-
ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any
legal rights other than those set out above, you may have additional statutory rights which will vary under the
laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.
THE SOURCE - WARRANTY
1
2
3
4
5
6
7
6
7
0~25% 25%~50% 50%~75% 75%~100%
TRUE WIRELESS
EARBUDS
HRB 5035
Additional large and small earbud tips
included (medium tips installed on earbuds).
Use the included charging cable to fully charge the case before rst
use. It will take approximately 1.5 hours to fully charge.
The LED will ash during charging, and remain solid when charging
is complete.
Red LED ON indicates power level is lower than 25%.
Yellow LED ON indicates power level is between 25%~50%.
Green LED ON indicates power level is between 50%~75%.
Blue LED ON indicates power level is between 75%~100%.
CHARGING THE EARBUDS
1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The
LED indicator will be solid blue/green/yellow/red (depending on the
charge case’s power level) when the earpbuds are charging and will
turn OFF when fully charged.
NOTE: Please make sure the charging case has enough power to
charge the earbuds. Prior to rst use, remove the plastic battery
isolator tabs located on the earbud charging points. When the earbuds
are paired to an Android™ or iOS device, the remaining earbud battery
power will show on the device display.
PAIRING
1. Open the lid of the charging case. The earbuds will automatically
turn ON. The LED will ash white and blue and the earbuds will
beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth�device list to pair the
earbuds automatically.
3. The earbuds will beep when Bluetooth�is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and
connect to your device when removed from the charging case,
provided both earbuds and your Bluetooth�are ON and
within range.
5. The earbuds will automatically turn OFF after 5 minutes if no
connection is established.
FIT
We recommend that you try each ear tip (small, medium and large),
then perform a sound check and choose the combination that provides
the best sound experience.
RESET
When the “L” and “R” earbuds cannot connect to each other, you will
need to reset the earbuds and clear the paired memory:
1. Remove HRB “5035” from your list of Bluetooth�devices.
2. Turn off Bluetooth�in your device settings.
3. Remove the earbuds from the charging case and turn them OFF.
Press and hold both MFB buttons for 8 seconds. The LED indicator
will be white, then blue and you will hear a beep when the earbuds
have been reset.
4. Return the earbuds to the charging case, close and then reopen the
lid. The earbuds will automatically turn ON and pair with each other.
You will hear a beep and the LED on the one earbud will ash blue
and white, the LED on the second earbud will ash blue.
5. Turn on Bluetooth®in your device settings, Select “HRB 5035” to pair.
Instruction Manual 8093128 OPERATING INSTRUCTIONS
Prior to rst use, remove the plastic battery isolator tabs located
on the earbud charging points.
TO DO THIS
Power ON Remove the earbuds from the charging case or
press and hold both MFB buttons for 2 seconds.
Power OFF Return the earbuds to the charging case. Alternatively,
when music is paused, you can press and hold either
MFB button for 4 seconds. If music is playing, this
function will not work.
Play Music Press either MFB button.
Pause Music Press either MFB button.
Next song Press the right MFB button twice.
Previous song Press the left MFB button twice.
Activate/Stop Voice Assistant Press either MFB button three times.
Volume up Press and hold the right MFB button for 2 seconds.
Volume down Press and hold the left MFB button for 2 seconds.
Answer a call Press either MFB button.
End a call Press either MFB button.
Reject an incoming call Press and hold either MFB button.
NOTE: The function compatibility may vary among different
smartphones or devices. Not all functions are available on all devices.
CHARGING THE CASE
OPERATION
• While playing music, press either MFB button to pause,
press again to resume
• Quickly press the right MFB twice for the next song, quickly press
the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an
incoming call. Press either MFB button once to answer the call,
press and hold to reject the call
WARNING!
• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over
extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you
should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the
earbuds may cause clicks which at high volume settings, may affect
your hearing. Therefore, always set the volume control to minimum
before switching between different sources (tuner, turntable, CD
player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard.
This product is not intended for use by small children and should be
kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the
earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose
of batteries in re to prevent an explosion
TROUBLESHOOTING
No sound
• Please check the volume on your audio device to make sure it is
outputting sound
Connection Problems
• Please return the earbuds to the case and then remove them again
if there are any connection issues
• Refer to the cleared paired memory and reset section
INTRODUCTION
Thank you for purchasing the HRB 5035 true wireless earbuds.
In order to maximize your listening experience please read the
following instructions.
WHAT’S INCLUDED
• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual
1
2
3
Charging pins
Charging case LED indicator
USB-C charging port
MFB (Multi-function button)
Earbud LED indicator
Charging contact point
Ear tip
The earbuds are not tting comfortably
• Please switch out the earbud tips to a different size to find the
appropriate fit
Improve the Sound
• Sound can sometimes be improved by moving to a larger eartip
size. The eartips still need to fit comfortably in your ear
CLEANING
Your earbuds may require periodic cleaning. Use a dry, soft, lint-free
cloth to clean your earbuds. To clean the microphone and speaker
mesh, use a dry cotton swab.
IMPORTANT SAFETY INFORMATION
CAUTIONS
• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product
SPECIFICATIONS
Bluetooth®version: v5.1
Bluetooth® proles*: HSP; HFP; A2DP; AVRCP;
APTX
EARBUDS
Wireless range: 10m (32ft.)
Playback time: approx. 11 hours**
Standby time: approx. 60 hours
Rated input: DC 5V/70mA
Driver diameter: 6mm
Sensitivity: 90db±3db
Frequency response: 20Hz~20kHz
Impedance: 16 Ohms±15%
Battery: Polymer Lithium
Battery capacity: 70mAh
Earbuds charging time: approx. 1.5 Hours
IP rating: IPX4
Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.
Please
Recycle
4
5
CHARGING CASE
Rated input: DC 5V, 500mA
Output: DC 5V, 300mA
Battery Capacity: 400mAh
Case charging time: Approx. 1.5 hours
Fully powered case: Provides up to 1.5 charges
*A2DP=Advanced Audio distribution Prole, AVRCP=Audio Video
Remote Control Prole, HSP=Handset Prole, HFP=Handfree Prole.
**Approximate playback time, battery life depends on individual use
and may be more or less than specied.
***Standby, Bluetooth® connected, power ON, no music playing.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth®SIG,
Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other
trademarks and trade names are those of their respective owners.
INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is
Subject to the following two conditions:
• This device may not cause interference, and this device must accept any
interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of Industry Canada
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of Industry Canada.
ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired
operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)
The Source warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available)
without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-
ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any
legal rights other than those set out above, you may have additional statutory rights which will vary under the
laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.
THE SOURCE - WARRANTY
1
2
3
4
5
6
7
6
7
0~25% 25%~50% 50%~75% 75%~100%
TRUE WIRELESS
EARBUDS
HRB 5035
Additional large and small earbud tips
included (medium tips installed on earbuds).
Use the included charging cable to fully charge the case before rst
use. It will take approximately 1.5 hours to fully charge.
The LED will ash during charging, and remain solid when charging
is complete.
Red LED ON indicates power level is lower than 25%.
Yellow LED ON indicates power level is between 25%~50%.
Green LED ON indicates power level is between 50%~75%.
Blue LED ON indicates power level is between 75%~100%.
CHARGING THE EARBUDS
1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The
LED indicator will be solid blue/green/yellow/red (depending on the
charge case’s power level) when the earpbuds are charging and will
turn OFF when fully charged.
NOTE: Please make sure the charging case has enough power to
charge the earbuds. Prior to rst use, remove the plastic battery
isolator tabs located on the earbud charging points. When the earbuds
are paired to an Android™ or iOS device, the remaining earbud battery
power will show on the device display.
PAIRING
1. Open the lid of the charging case. The earbuds will automatically
turn ON. The LED will ash white and blue and the earbuds will
beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth�device list to pair the
earbuds automatically.
3. The earbuds will beep when Bluetooth�is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and
connect to your device when removed from the charging case,
provided both earbuds and your Bluetooth�are ON and
within range.
5. The earbuds will automatically turn OFF after 5 minutes if no
connection is established.
FIT
We recommend that you try each ear tip (small, medium and large),
then perform a sound check and choose the combination that provides
the best sound experience.
RESET
When the “L” and “R” earbuds cannot connect to each other, you will
need to reset the earbuds and clear the paired memory:
1. Remove HRB “5035” from your list of Bluetooth�devices.
2. Turn off Bluetooth�in your device settings.
3. Remove the earbuds from the charging case and turn them OFF.
Press and hold both MFB buttons for 8 seconds. The LED indicator
will be white, then blue and you will hear a beep when the earbuds
have been reset.
4. Return the earbuds to the charging case, close and then reopen the
lid. The earbuds will automatically turn ON and pair with each other.
You will hear a beep and the LED on the one earbud will ash blue
and white, the LED on the second earbud will ash blue.
5. Turn on Bluetooth®in your device settings, Select “HRB 5035” to pair.
Instruction Manual 8093128 OPERATING INSTRUCTIONS
Prior to rst use, remove the plastic battery isolator tabs located
on the earbud charging points.
TO DO THIS
Power ON Remove the earbuds from the charging case or
press and hold both MFB buttons for 2 seconds.
Power OFF Return the earbuds to the charging case. Alternatively,
when music is paused, you can press and hold either
MFB button for 4 seconds. If music is playing, this
function will not work.
Play Music Press either MFB button.
Pause Music Press either MFB button.
Next song Press the right MFB button twice.
Previous song Press the left MFB button twice.
Activate/Stop Voice Assistant Press either MFB button three times.
Volume up Press and hold the right MFB button for 2 seconds.
Volume down Press and hold the left MFB button for 2 seconds.
Answer a call Press either MFB button.
End a call Press either MFB button.
Reject an incoming call Press and hold either MFB button.
NOTE: The function compatibility may vary among different
smartphones or devices. Not all functions are available on all devices.
CHARGING THE CASE
OPERATION
• While playing music, press either MFB button to pause,
press again to resume
• Quickly press the right MFB twice for the next song, quickly press
the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an
incoming call. Press either MFB button once to answer the call,
press and hold to reject the call
WARNING!
• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over
extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you
should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the
earbuds may cause clicks which at high volume settings, may affect
your hearing. Therefore, always set the volume control to minimum
before switching between different sources (tuner, turntable, CD
player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard.
This product is not intended for use by small children and should be
kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the
earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose
of batteries in re to prevent an explosion
TROUBLESHOOTING
No sound
• Please check the volume on your audio device to make sure it is
outputting sound
Connection Problems
• Please return the earbuds to the case and then remove them again
if there are any connection issues
• Refer to the cleared paired memory and reset section
INTRODUCTION
Thank you for purchasing the HRB 5035 true wireless earbuds.
In order to maximize your listening experience please read the
following instructions.
WHAT’S INCLUDED
• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual
1
2
3
Charging pins
Charging case LED indicator
USB-C charging port
MFB (Multi-function button)
Earbud LED indicator
Charging contact point
Ear tip
The earbuds are not tting comfortably
• Please switch out the earbud tips to a different size to find the
appropriate fit
Improve the Sound
• Sound can sometimes be improved by moving to a larger eartip
size. The eartips still need to fit comfortably in your ear
CLEANING
Your earbuds may require periodic cleaning. Use a dry, soft, lint-free
cloth to clean your earbuds. To clean the microphone and speaker
mesh, use a dry cotton swab.
IMPORTANT SAFETY INFORMATION
CAUTIONS
• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product
SPECIFICATIONS
Bluetooth®version: v5.1
Bluetooth® proles*: HSP; HFP; A2DP; AVRCP;
APTX
EARBUDS
Wireless range: 10m (32ft.)
Playback time: approx. 11 hours**
Standby time: approx. 60 hours
Rated input: DC 5V/70mA
Driver diameter: 6mm
Sensitivity: 90db±3db
Frequency response: 20Hz~20kHz
Impedance: 16 Ohms±15%
Battery: Polymer Lithium
Battery capacity: 70mAh
Earbuds charging time: approx. 1.5 Hours
IP rating: IPX4
Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.
Please
Recycle
4
5
CHARGING CASE
Rated input: DC 5V, 500mA
Output: DC 5V, 300mA
Battery Capacity: 400mAh
Case charging time: Approx. 1.5 hours
Fully powered case: Provides up to 1.5 charges
*A2DP=Advanced Audio distribution Prole, AVRCP=Audio Video
Remote Control Prole, HSP=Handset Prole, HFP=Handfree Prole.
**Approximate playback time, battery life depends on individual use
and may be more or less than specied.
***Standby, Bluetooth® connected, power ON, no music playing.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth®SIG,
Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other
trademarks and trade names are those of their respective owners.
INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is
Subject to the following two conditions:
• This device may not cause interference, and this device must accept any
interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of Industry Canada
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of Industry Canada.
ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired
operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)
The Source warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available)
without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-
ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any
legal rights other than those set out above, you may have additional statutory rights which will vary under the
laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.
THE SOURCE - WARRANTY
1
2
3
4
5
6
7
6
7
0~25% 25%~50% 50%~75% 75%~100%
TRUE WIRELESS
EARBUDS
HRB 5035
Additional large and small earbud tips
included (medium tips installed on earbuds).
Use the included charging cable to fully charge the case before rst
use. It will take approximately 1.5 hours to fully charge.
The LED will ash during charging, and remain solid when charging
is complete.
Red LED ON indicates power level is lower than 25%.
Yellow LED ON indicates power level is between 25%~50%.
Green LED ON indicates power level is between 50%~75%.
Blue LED ON indicates power level is between 75%~100%.
CHARGING THE EARBUDS
1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The
LED indicator will be solid blue/green/yellow/red (depending on the
charge case’s power level) when the earpbuds are charging and will
turn OFF when fully charged.
NOTE: Please make sure the charging case has enough power to
charge the earbuds. Prior to rst use, remove the plastic battery
isolator tabs located on the earbud charging points. When the earbuds
are paired to an Android™ or iOS device, the remaining earbud battery
power will show on the device display.
PAIRING
1. Open the lid of the charging case. The earbuds will automatically
turn ON. The LED will ash white and blue and the earbuds will
beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth�device list to pair the
earbuds automatically.
3. The earbuds will beep when Bluetooth�is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and
connect to your device when removed from the charging case,
provided both earbuds and your Bluetooth�are ON and
within range.
5. The earbuds will automatically turn OFF after 5 minutes if no
connection is established.
FIT
We recommend that you try each ear tip (small, medium and large),
then perform a sound check and choose the combination that provides
the best sound experience.
RESET
When the “L” and “R” earbuds cannot connect to each other, you will
need to reset the earbuds and clear the paired memory:
1. Remove HRB “5035” from your list of Bluetooth�devices.
2. Turn off Bluetooth�in your device settings.
3. Remove the earbuds from the charging case and turn them OFF.
Press and hold both MFB buttons for 8 seconds. The LED indicator
will be white, then blue and you will hear a beep when the earbuds
have been reset.
4. Return the earbuds to the charging case, close and then reopen the
lid. The earbuds will automatically turn ON and pair with each other.
You will hear a beep and the LED on the one earbud will ash blue
and white, the LED on the second earbud will ash blue.
5. Turn on Bluetooth®in your device settings, Select “HRB 5035” to pair.
Instruction Manual 8093128 OPERATING INSTRUCTIONS
Prior to rst use, remove the plastic battery isolator tabs located
on the earbud charging points.
TO DO THIS
Power ON Remove the earbuds from the charging case or
press and hold both MFB buttons for 2 seconds.
Power OFF Return the earbuds to the charging case. Alternatively,
when music is paused, you can press and hold either
MFB button for 4 seconds. If music is playing, this
function will not work.
Play Music Press either MFB button.
Pause Music Press either MFB button.
Next song Press the right MFB button twice.
Previous song Press the left MFB button twice.
Activate/Stop Voice Assistant Press either MFB button three times.
Volume up Press and hold the right MFB button for 2 seconds.
Volume down Press and hold the left MFB button for 2 seconds.
Answer a call Press either MFB button.
End a call Press either MFB button.
Reject an incoming call Press and hold either MFB button.
NOTE: The function compatibility may vary among different
smartphones or devices. Not all functions are available on all devices.
CHARGING THE CASE
OPERATION
• While playing music, press either MFB button to pause,
press again to resume
• Quickly press the right MFB twice for the next song, quickly press
the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an
incoming call. Press either MFB button once to answer the call,
press and hold to reject the call
WARNING!
• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over
extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you
should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the
earbuds may cause clicks which at high volume settings, may affect
your hearing. Therefore, always set the volume control to minimum
before switching between different sources (tuner, turntable, CD
player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard.
This product is not intended for use by small children and should be
kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the
earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose
of batteries in re to prevent an explosion
TROUBLESHOOTING
No sound
• Please check the volume on your audio device to make sure it is
outputting sound
Connection Problems
• Please return the earbuds to the case and then remove them again
if there are any connection issues
• Refer to the cleared paired memory and reset section
INTRODUCTION
Thank you for purchasing the HRB 5035 true wireless earbuds.
In order to maximize your listening experience please read the
following instructions.
WHAT’S INCLUDED
• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual
1
2
3
Charging pins
Charging case LED indicator
USB-C charging port
MFB (Multi-function button)
Earbud LED indicator
Charging contact point
Ear tip
The earbuds are not tting comfortably
• Please switch out the earbud tips to a different size to find the
appropriate fit
Improve the Sound
• Sound can sometimes be improved by moving to a larger eartip
size. The eartips still need to fit comfortably in your ear
CLEANING
Your earbuds may require periodic cleaning. Use a dry, soft, lint-free
cloth to clean your earbuds. To clean the microphone and speaker
mesh, use a dry cotton swab.
IMPORTANT SAFETY INFORMATION
CAUTIONS
• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product
SPECIFICATIONS
Bluetooth®version: v5.1
Bluetooth® proles*: HSP; HFP; A2DP; AVRCP;
APTX
EARBUDS
Wireless range: 10m (32ft.)
Playback time: approx. 11 hours**
Standby time: approx. 60 hours
Rated input: DC 5V/70mA
Driver diameter: 6mm
Sensitivity: 90db±3db
Frequency response: 20Hz~20kHz
Impedance: 16 Ohms±15%
Battery: Polymer Lithium
Battery capacity: 70mAh
Earbuds charging time: approx. 1.5 Hours
IP rating: IPX4
Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.
Please
Recycle
4
5
CHARGING CASE
Rated input: DC 5V, 500mA
Output: DC 5V, 300mA
Battery Capacity: 400mAh
Case charging time: Approx. 1.5 hours
Fully powered case: Provides up to 1.5 charges
*A2DP=Advanced Audio distribution Prole, AVRCP=Audio Video
Remote Control Prole, HSP=Handset Prole, HFP=Handfree Prole.
**Approximate playback time, battery life depends on individual use
and may be more or less than specied.
***Standby, Bluetooth® connected, power ON, no music playing.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth®SIG,
Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other
trademarks and trade names are those of their respective owners.
INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is
Subject to the following two conditions:
• This device may not cause interference, and this device must accept any
interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of Industry Canada
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of Industry Canada.
ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired
operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)
The Source warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available)
without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-
ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any
legal rights other than those set out above, you may have additional statutory rights which will vary under the
laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.
THE SOURCE - WARRANTY
1
2
3
4
5
6
7
6
7
0~25% 25%~50% 50%~75% 75%~100%
TRUE WIRELESS
EARBUDS
HRB 5035
Additional large and small earbud tips
included (medium tips installed on earbuds).
Use the included charging cable to fully charge the case before rst
use. It will take approximately 1.5 hours to fully charge.
The LED will ash during charging, and remain solid when charging
is complete.
Red LED ON indicates power level is lower than 25%.
Yellow LED ON indicates power level is between 25%~50%.
Green LED ON indicates power level is between 50%~75%.
Blue LED ON indicates power level is between 75%~100%.
CHARGING THE EARBUDS
1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The
LED indicator will be solid blue/green/yellow/red (depending on the
charge case’s power level) when the earpbuds are charging and will
turn OFF when fully charged.
NOTE: Please make sure the charging case has enough power to
charge the earbuds. Prior to rst use, remove the plastic battery
isolator tabs located on the earbud charging points. When the earbuds
are paired to an Android™ or iOS device, the remaining earbud battery
power will show on the device display.
PAIRING
1. Open the lid of the charging case. The earbuds will automatically
turn ON. The LED will ash white and blue and the earbuds will
beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth�device list to pair the
earbuds automatically.
3. The earbuds will beep when Bluetooth�is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and
connect to your device when removed from the charging case,
provided both earbuds and your Bluetooth�are ON and
within range.
5. The earbuds will automatically turn OFF after 5 minutes if no
connection is established.
FIT
We recommend that you try each ear tip (small, medium and large),
then perform a sound check and choose the combination that provides
the best sound experience.
RESET
When the “L” and “R” earbuds cannot connect to each other, you will
need to reset the earbuds and clear the paired memory:
1. Remove HRB “5035” from your list of Bluetooth�devices.
2. Turn off Bluetooth�in your device settings.
3. Remove the earbuds from the charging case and turn them OFF.
Press and hold both MFB buttons for 8 seconds. The LED indicator
will be white, then blue and you will hear a beep when the earbuds
have been reset.
4. Return the earbuds to the charging case, close and then reopen the
lid. The earbuds will automatically turn ON and pair with each other.
You will hear a beep and the LED on the one earbud will ash blue
and white, the LED on the second earbud will ash blue.
5. Turn on Bluetooth®in your device settings, Select “HRB 5035” to pair.
Instruction Manual 8093128 OPERATING INSTRUCTIONS
Prior to rst use, remove the plastic battery isolator tabs located
on the earbud charging points.
TO DO THIS
Power ON Remove the earbuds from the charging case or
press and hold both MFB buttons for 2 seconds.
Power OFF Return the earbuds to the charging case. Alternatively,
when music is paused, you can press and hold either
MFB button for 4 seconds. If music is playing, this
function will not work.
Play Music Press either MFB button.
Pause Music Press either MFB button.
Next song Press the right MFB button twice.
Previous song Press the left MFB button twice.
Activate/Stop Voice Assistant Press either MFB button three times.
Volume up Press and hold the right MFB button for 2 seconds.
Volume down Press and hold the left MFB button for 2 seconds.
Answer a call Press either MFB button.
End a call Press either MFB button.
Reject an incoming call Press and hold either MFB button.
NOTE: The function compatibility may vary among different
smartphones or devices. Not all functions are available on all devices.
CHARGING THE CASE
OPERATION
• While playing music, press either MFB button to pause,
press again to resume
• Quickly press the right MFB twice for the next song, quickly press
the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an
incoming call. Press either MFB button once to answer the call,
press and hold to reject the call
WARNING!
• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over
extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you
should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the
earbuds may cause clicks which at high volume settings, may affect
your hearing. Therefore, always set the volume control to minimum
before switching between different sources (tuner, turntable, CD
player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard.
This product is not intended for use by small children and should be
kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the
earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose
of batteries in re to prevent an explosion
TROUBLESHOOTING
No sound
• Please check the volume on your audio device to make sure it is
outputting sound
Connection Problems
• Please return the earbuds to the case and then remove them again
if there are any connection issues
• Refer to the cleared paired memory and reset section
INTRODUCTION
Thank you for purchasing the HRB 5035 true wireless earbuds.
In order to maximize your listening experience please read the
following instructions.
WHAT’S INCLUDED
• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual
1
2
3
Charging pins
Charging case LED indicator
USB-C charging port
MFB (Multi-function button)
Earbud LED indicator
Charging contact point
Ear tip
The earbuds are not tting comfortably
• Please switch out the earbud tips to a different size to find the
appropriate fit
Improve the Sound
• Sound can sometimes be improved by moving to a larger eartip
size. The eartips still need to fit comfortably in your ear
CLEANING
Your earbuds may require periodic cleaning. Use a dry, soft, lint-free
cloth to clean your earbuds. To clean the microphone and speaker
mesh, use a dry cotton swab.
IMPORTANT SAFETY INFORMATION
CAUTIONS
• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product
SPECIFICATIONS
Bluetooth®version: v5.1
Bluetooth® proles*: HSP; HFP; A2DP; AVRCP;
APTX
EARBUDS
Wireless range: 10m (32ft.)
Playback time: approx. 11 hours**
Standby time: approx. 60 hours
Rated input: DC 5V/70mA
Driver diameter: 6mm
Sensitivity: 90db±3db
Frequency response: 20Hz~20kHz
Impedance: 16 Ohms±15%
Battery: Polymer Lithium
Battery capacity: 70mAh
Earbuds charging time: approx. 1.5 Hours
IP rating: IPX4
Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.
Please
Recycle
4
5
CHARGING CASE
Rated input: DC 5V, 500mA
Output: DC 5V, 300mA
Battery Capacity: 400mAh
Case charging time: Approx. 1.5 hours
Fully powered case: Provides up to 1.5 charges
*A2DP=Advanced Audio distribution Prole, AVRCP=Audio Video
Remote Control Prole, HSP=Handset Prole, HFP=Handfree Prole.
**Approximate playback time, battery life depends on individual use
and may be more or less than specied.
***Standby, Bluetooth® connected, power ON, no music playing.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth®SIG,
Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other
trademarks and trade names are those of their respective owners.
INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is
Subject to the following two conditions:
• This device may not cause interference, and this device must accept any
interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of Industry Canada
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of Industry Canada.
ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired
operation of the device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)
The Source warrants that this product will be free from defects in materials and workmanship for a period of
twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available)
without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-
ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any
legal rights other than those set out above, you may have additional statutory rights which will vary under the
laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.
THE SOURCE - WARRANTY
1
2
3
4
5
6
7
6
7
0~25% 25%~50% 50%~75% 75%~100%
TRUE WIRELESS
EARBUDS
HRB 5035
Additional large and small earbud tips
included (medium tips installed on earbuds).
Table of contents
Other HEADRUSH Headphones manuals
