Healthcraft SP-S User manual

Thank you for purchasing the SuperPole System. We are
confident that you will find the unique design and durable
construction of this HealthCraft product to be of great assistance
in your daily routine.
To fully enjoy your SuperPole System, please take a few moments
to read these instructions. You should store these instructions in a
safe place for future reference.
CAUTION:
IMPORTANT:
NOTE:
It is your responsibility to see that your SuperPole
System is properly assembled, installed, and cared for. Failure
to follow instructions in this manual could result in serious injury.
The SuperPole System should only be used in
locations where the floor and ceiling surfaces are structurally
sound. It should not be installed on loose floor coverings, in
rooms with radiant ceiling heating, in mobile homes or with
suspended or angled ceilings. Recommended weight limit is
250 lb. Not more than 150 lbs should be exerted on trapeze
handle (sitting up assistance only). If you are not equipped to
undertake the outlined work, we would recommend that you
have your SuperPole System installed by a qualified contractor.
The extension screw feature of the SuperPole System can
generate enough force to damage a ceiling. Exercise caution
when tightening this screw.
It is recommended that the ceiling anchor plate be
installed to span across two joists in a ceiling as shown below.
In cases where this may not be possible (i.e. one joist only), be
sure to test the pole rigorously after installation to be certain of
a secure installation.
We strongly recommend that you give thought as to the optimal
location of your SuperPole System before installation. The
following questions may help you to decide upon a location:
a. What motions will you be going through? (pulling up to
standing, lowering to sitting, transferring from chair to toilet,
etc.)
b. Where will you need the most support? (while walking, while
lifting, etc.)
c. What is your strongest side/hand?
d. What is your complete transfer path? Will the location allow
for full support over most of your path of motion?
e. Will the pole be far enough away to allow you to stand
comfortably?
Locate pole adjacent to hip/belt line and
as close to bed as possible while
allowing clearance for bed coverings. If
using SuperBar option, you will need to
set the pivot locking positions of the
bar. As a suggestion, positions A and E
are good for moving in bed, B for
pulling up to sitting, C for pulling up to
standing and D for transferring out of
bed.
Toilet
Bathtub only
- locate pole between three to
ten inches forward of the knees and
two to six inches to side of knees when
seated. - locate pole
base against tub, approximately half
way along its length. If using SuperBar
option, you will need to set the pivot
locking positions of the bar. As a
suggestion, positions B or D are
suitable for standing from toilet, C and
F for transferring into bathtub, E and D
for transferring out of bathtub.
Locate pole between three to ten
inches forward of the knees and two to
six inches to side of knees when
seated. If using SuperBar option, you
will need to set the pivot locking
positions of the bar. As a suggestion,
positions A or C are suitable for
standing assistance, while D and E are
suitable for completing a transfer to a
nearby walker or wheelchair. Position
B provides side support if this is
preferred for standing.
CAUTION:
IMPORTANT:
The SuperPole System can loosen due to settling
of the floor or ceiling, particularly in the first hours and days
following installation. As a result, we recommend that you test
that the pole is secure, and the extension screw tightened if
needed during this time, and then on a monthly basis.
Use of screws in ceiling anchor plate - The
ceiling anchor plate has two holes that may be used to
accommodate screws to better anchor this plate directly to the
ceiling or ceiling joists. It is strongly recommended to install
screws to prevent slippage in the following situations:
1. You expect to subject the pole to heavy usage such as when
the pole is used for more than mild support for side to side
stability.
2. You are not able to inspect, or have inspected (and tighten if
neccessary) the extension screw on a monthly basis.
Thank You...Thank You ...
Safety ConsiderationsSafety Considerations
Getting Started...Getting Started . . .
Ceiling
Joists
Pole
Anchor Plate
spanning
across 2 joists
Installation Instructions
Models SPS, SPB, STP
www.healthcraftproducts.com
The
System
SuperPole
Bed
A
B
B
B
E
A
D
DE
AC
C
F
C
E
D
Bathtub and/or Toilet
Chair
ealth
Craft
H
TM

A3. Unpack the cover sleeve (4). The cover sleeve has two
end pieces - remove the solid steel socket (5). Next slide the
cover sleeve onto the bottom of the pole (2) as shown in figure
A2, with the remaining grey plastic bushing (6) at the top.
A4. Remove the rubber O-ring (7) from its bag, and stretch it
to fit onto the bottom of the pole (2), leaving it a few inches up
from the bottom of the pole as shown in figure A2. The cover
sleeve (4) can now slide down to rest on this O-ring while the
pole is being raised.
A5. Place the circular
base (8) on the floor at
the intended location of
the SuperPole. Place
the steel socket (5) on
top of the base so that it
seats into the central
hole of the circular
base. You are now
ready to raise the
SuperPole assembly.
A6. Raising the Pole - The SuperPole is most easily raised by
holding the pole up at an angle, inserting the bottom of the
extension screw into the metal socket (5) on the circular base
(8), and then pivoting the pole up above the socket as shown in
figure A4. to prepare, set the extension screw such that
the distance from the top of the ceiling anchor plate (1) to the
bottom of the extension screw is about two inches less than the
actual floor to ceiling height. You may need to unscrew the jam
nut downward to allow the extension screw to rotate.
HINT -
A7.Set the SuperPole to a true
vertical position. This may be
facilitated using a construction
level, plumb bob, or by visually
comparing the pole with other
vertical line features in the room
such as wall corners, etc.
It is easier to swing the
pole up from one of the sides of
the anchor plate as shown in
figure A4. If the anchor plate hits
the ceiling prior to reaching
vertical you will need to shorten
the length of the extension screw.
HINT -
A8. Tightening the pole - while the cover sleeve is held up by the
O-ring , insert a bar such as the shaft of a screwdriver, through the
drive hole of the extension screw. Turn the extension screw
(clockwise) as shown in figure A5 to make the anchor plate contact
the ceiling. - The anchor plate must be made to
contact the ceiling squarely. This can be facilitated by having a
second person hold the pole exactly vertical while turning the
extension screw. Continue turning the extension screw until the
anchor plate contacts the ceiling squarely. From this point
continue to turn the extension screw approximately two to five
turns until the SuperPole is secure and ready for testing in step A9.
IMPORTANT
A9. Testing installation - test the
SuperPole by firmly holding onto the
pole at mid-height and rigorously
attempting to force the pole from side
to side. If either the base, or the
anchor plate appear to slide or shift,
tighten the extension screw one more
turn and repeat the test until the pole
will not move during this test.
A10. IMPORTANT -Lock
extension screw after installing
pole by turning jam nut up until
touching the bottom of the pole,
then, simultaneously turning jam
nut and extension screw
backwards until jammed tight as
shown in steps1&2offigure A6.
When finally tight, remove the
turning rod, slide down the O-ring
(it stores on top of the metal
socket), and move the cover
sleeve down onto the metal
socket. Your SuperPole is now
installed.
Figure A2Figure A2
6
4
7
Figure A3Figure A3
5
8
Figure A5Figure A5
Figure A6Figure A6
A1. Unpack the ceiling anchor plate (1) from the rectangular
box, and the pole assembly (2) from the cardboard tube
(remove staples to avoid scratching the pole). Remove the
locking pin (3) from the pole receptacle in the center of the
anchor plate.
Prior to installing the SuperPole System, we strongly
recommend that you first read through these instructions. We
would also recommend that you set aside a space on the floor
or a table to prepare the SuperPole System prior to raising the
pole for final installation.
A2. Slide the top end of the pole (2) onto the receptacle of the
ceiling anchor plate (1) as shown in figure A1. Set the pole so
that the locking pin holes of the pole and the receptacle align.
At this point re-insert the locking pin (3) removed in step A1.
1
2
3
Figure A1Figure A1
Figure A4Figure A4
2
8
Installation
Instructions
Models SP-S, SP-CXX
-2-
1
2

B2. Unpack the SuperBar hand rail unit (10). Locate the small
Allen key wrench (11). Using this Allen key wrench, unscrew the
bottom countersunk screw (12) as shown in figure B1. Pull out
the white plastic pivot bushing (13) and set it and the screw
aside.
B1.See steps A1 and A2 on page 2. Complete these
instructions and then continue with step B2.
B5. See steps A3, A4, and A5 on page 2. Complete these
instructions and then continue with step B6.
B8. See steps A6 through A9 on page 2. Complete these
instructions to finish the installation of your SuperPole with
SuperBar.
Alternate Installation Option
Steps B6 and B7 can be completed the pole
has been raised in place (steps A6, A7, A8) to
better determine optimal height and locking
positions of the SuperBar. You may also install just
one set screw to test a height/angle setting of the
SuperBar.
- Should you need to change the position of
the height/angle setting, we recommend that you
change the height by at least one inch. This will
avoid set screw indentations from being too close to
each other and thereby weakening the pole.
after
Note!
B3. Slide the SuperBar hand rail unit (10) onto the pole
assembly (2) as shown in figure B2. (side with remaining pivot
bushing to go on first). Slide it on as straight as possible to
avoid scratching the paint on the pole.
B4.Unpack and slide the grooved collar (14) onto the pole (2)
as shown in figure B2. Gently slide the collar up the pole to
avoid scratching the pole. Next slide the white plastic pivot
bushing (13) (removed in step B2) up the pole (2) as shown in
figure B2.
IMPORTANT - the next step is to fix the grooved collar (14) to the
pole (2). The position of the grooved collar is important in two
ways; first, the height at which you fix the grooved collar
determines the height of the SuperBar hand rail unit (10), and
secondly, each of the grooves correspond to a rotational locking
position of the hand rail unit (refer to figure B3). You will want to
fix the grooves to have the hand rail lock in the most
advantageous positions for your assistance as discussed on
page 1 ("Getting Started")
B6.Once the grooved collar (14) has been set to its desired
location, fasten the grooved collar to the pole (2) by installing and
tightening the three set screws (15) with the larger Allen key
wrench (16). You will need to slide the spring collar (17) upward
to gain access to the screw holes. -
MUST or
injury may result - by tightening these set screws, the
cone points will penetrate the pole for positive engagement,
thereby leaving permanent indentations in the pole.
IMPORTANT These screws
be tightened until they are flush with the collar
. NOTE
BE
CERTAIN THAT THE COLLAR IS AT THE CORRECT HEIGHT
AND ORIENTATION BEFORE PROCEEDING. Next, slide the
spring collar(17) downward on the grooved collar(14) as shown
to retain set screws(15) while in service. Inspect frequently to
ensure screws and collar are tight.
B7. Re-install the white plastic pivot bushing (13) removed in
step B2/figure B1 and secure it with the countersunk screw (12)
using the small Allen wrench (11).
10
13
12
11
Figure B1Figure B1
2
17
14
15
16
Height of hand rail
Rotational
locking position
Figure B3Figure B3
10
13
14 2
Figure B2Figure B2
Prior to installing the SuperBar option, we strongly recommend
that you first read through these instructions. We would also
recommend that you set aside a space on the floor or a table to
prepare the SuperPole System prior to raising the pole for final
installation.
Installation
Instructions
Models SPB-S, SPB-CXX
-3-
spring collar
installed

C1. See step A1 on page 2. Complete this instruction and
then continue with step C2.
C3. (bedside use) - Refer to
figure C2. The actual user of the SuperTrapeze should lie down
in bed in their normal resting position. The location of the pole
alongside the bed is recommended to be directly beside the
hip/belt line as shown by "A" in figure C2. Also, it is
recommended to situate the pole as close to the side of the bed
as possible while leaving enough clearance for the bed
coverings.
Determining Location of Pole
C2. Unpack the support arm (20). Slide it onto the top end of
the pole (2) such that the strap hook is down as shown in figure
C1. Move it gently down the pole until it rests against the top of
the grey grip (21).
C4. See steps A2 through A9 on page 2. These steps will
guide you to raise and secure the pole in the location as
determined in step C3. Complete these instructions and then
continue with step C5.
C5. Once the pole has been installed beside the bed, hold the
trapeze handle under the strap, such that the upper rail of the
handle is closest to the head of the bed as shown in figure C2.
Next, open the loop on the end of the trapeze strap (22), rotate
the strap 180 degrees, and slide it on to the upper rail of the
trapeze handle (23) as shown in figure C3. Slide it past the grip
and along the trapeze tube until it reaches the top bend of the
trapeze as also shown in figure C3.
C7.Setting the trapeze handle height - Set the trapeze at an
appropriate height by adjusting the length of the strap. This is
done by pulling some slack through the cross pieces of the strap
buckle and pulling the buckle down to shorten the strap, or sliding
it up to lengthen the strap. The trapeze handle is generally at an
appropriate height when ones fingers can comfortably grasp
around the bottom rail of the trapeze when lying down in bed as
shown by "C" in figure C2.
C8. Testing the location - Have the user gently try the installed
location of the trapeze handle and pole. Ensure that the trapeze
handle is not too close to allow a comfortable sit up action.
Should the trapeze support arm need to be moved, remove the
set screw installed in step C6, and lift the support arm up by at
least one inch and reinstall the screw with the arm at a new
angle to avoid the set screw being too close to the previous
indent created in the pole by step C6.
C9.Once the trapeze has been confirmed as the correct
location, fully install all three set screws. IMPORTANT - The set
screws should be installed such that the back end of the screw is
flush with the outer surface of the support arm or injury may
result. Slide the spring collar(26) down over the top of support
arm as shown to retain the screws in service. Your SuperTrapeze
Plus option is now installed.
C6.Setting Height and Angle of Support Arm - Refer to figure
C2. Using a tape measure, make a small pencil mark on the pole
at a suggested height of 84" from the floor. Have the actual user
lie down in bed in their normal lying position with their hands
placed palm down on their thighs as shown in figure C2. Locate
the cone point set screws (25) and allen wrench (24) and have
them close at hand. Gently slide the support arm up the pole until
the top of the barrel reaches the 84" mark as shown by "B1" in
figure C2. Next, swing the support arm so that the strap hangs
directly over the palms of the user as shown by "B2". Secure the
support arm to the pole with one of the set screws (25) and allen
wrench (24) as shown in figure C4.
Prior to installing the SuperTrapeze Plus option, we strongly
recommend that you first read through these instructions. We
would also recommend that you set aside a space on the floor
or a table to prepare the SuperTrapeze Plus prior to raising the
pole for final installation.
A
B1
C
B2
20
21
2
22
24
25
26
20
23
Figure C1Figure C1
Figure C4Figure C4
Figure C3Figure C3
Figure C2Figure C2
Installation
Instructions
Models STP-S, STP-CXX
-4-
spring collar
installed