Pilz PSEN sl-0.5n 2.2 User manual

PSEN sl-0.5n 2.1/2.2
Operating Manual-1003805-EN-03
}PSEN sensor technology

Preface
This document is the original document.
Where unavoidable, for reasons of readability, the masculine form has been selected when
formulating this document. We do assure you that all persons are regarded without discrim-
ination and on an equal basis.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for the user's internal purposes. Suggestions and comments for improving this documenta-
tion will be gratefully received.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital

Contents
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 3
Introduction ............................................................................................................................5
Validity of documentation.......................................................................................................... 5
Using the documentation .......................................................................................................... 5
Definition of symbols................................................................................................................. 5
Safety ...................................................................................................................................... 6
Intended use ............................................................................................................................. 6
Safety regulations ..................................................................................................................... 7
Safety assessment ................................................................................................................... 7
Use of qualified personnel ........................................................................................................ 7
Warranty and liability ................................................................................................................ 8
Disposal .................................................................................................................................... 8
For your safety.......................................................................................................................... 8
Unit features ...........................................................................................................................9
Function description ............................................................................................................. 9
Lateral and vertical offset.......................................................................................................... 10
Wiring ......................................................................................................................................11
Guidelines for cable length ....................................................................................................... 11
Recommended cable cross sections ........................................................................................ 11
Pin assignment ......................................................................................................................... 12
Connection to evaluation devices ........................................................................................ 12
Connection example PNOZs3 ................................................................................................. 13
Connection example PNOZmulti .............................................................................................. 14
Teaching in the actuator ....................................................................................................... 15
PSEN sl-0.5n 2.1 ...................................................................................................................... 15
PSEN sl-0.5n 2.2 ...................................................................................................................... 15
Installation ..............................................................................................................................16
Note regarding the free-moving actuator PSEN sl-0.5fm ......................................................... 17
Installing on a swing gate ......................................................................................................... 18
Installing on a sliding gate ........................................................................................................ 19
Adjustment ............................................................................................................................. 20
Operation ................................................................................................................................21
Error display through flashing codes ........................................................................................ 21

Contents
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 4
Dimensions in mm .................................................................................................................23
Technical Details Order No. 570504-570505 ........................................................................ 25
Technical Details Order No. 570564-570565 ........................................................................ 28
Supplementary data ..............................................................................................................31
Radio approval.......................................................................................................................... 31
Safety characteristic data ..................................................................................................... 31
Classification according to ZVEI, CB24I .............................................................................. 32
Order reference ......................................................................................................................33
Safety gate system ................................................................................................................... 33
Accessories .............................................................................................................................. 33
EC declaration of conformity ................................................................................................ 33
UKCA-Declaration of Conformity ......................................................................................... 33

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 5
Introduction
Validity of documentation
This documentation is valid for the product PSEN sl-0.5n 2.1/2.2. It is valid until new docu-
mentation is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
Using the documentation
This document is intended for instruction. Only install and commission the product if you
have read and understood this document. The document should be retained for future ref-
erence.
Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 6
INFORMATION
This gives advice on applications and provides information on special fea-
tures.
Safety
Intended use
Safety function of safety switch:
}2 safety outputs, each of which supply a high signal when the actuator is in the safety
switch's response range.
The safety gate system meets the requirements in accordance with
}EN 60947-5-3: PDDB with the corresponding actuator PSEN sl0.5 or PSEN sl0.5fm (see
Technical details: System with normal actuator [ 25], System with free-moving
actuator [ 28])
}EN 62061: SIL CL 3
}EN ISO 13849-1: PL e and Cat. 4
}EN ISO 14119: Coding level High, Type 4
}The safety switch may only be used with the corresponding actuator (see Technical De-
tails: System with normal actuator [ 25], System with free-moving actuator [ 28]).
The safety level PL e (Cat. 4)/SIL CL 3 is only achieved if
}the safety outputs use 2-channel processing.
NOTICE
Positioning of the safety switch
As the safety switch is not intended for a guard locking device for personal
protection, the safeguard monitored by the safety switch must be positioned
in a way that the access time corresponds at least to the machine's stopping
time.
Because of the low operating distance (see Technical details [ 25]) the repetition ac-
curacy of 40 % deviates from the requirement in accordance with EN 60947-5-2 (max.
10%).
Improper use
The following is deemed improper use in particular
}Any component, technical or electrical modification to the product,
}Use of the product outside the areas described in this operating manual,
}Use of the product outside the technical details (see Technical details [ 25]).

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 7
NOTICE
EMC-compliant electrical installation
The product is designed for use in an industrial environment. The product
may cause interference if installed in other environments. If installed in other
environments, measures should be taken to comply with the applicable
standards and directives for the respective installation site with regard to in-
terference.
INFORMATION
The magnet surface and counterplate may heat up. When installing,
make sure that heat dissipation is guaranteed.
Safety regulations
Safety assessment
Before using a device, a safety assessment in accordance with the Machinery Directive is
required.
The product as an individual component fulfils the functional safety requirements in accord-
ance with EN ISO 13849 and EN 62061. However, this does not guarantee the functional
safety of the overall plant/machine. To achieve the relevant safety level of the overall plant/
machine’s required safety functions, each safety function needs to be considered separ-
ately.
Use of qualified personnel
The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by persons who are competent to do so.
A competent person is a qualified and knowledgeable person who, because of their train-
ing, experience and current professional activity, has the specialist knowledge required. To
be able to inspect, assess and operate devices, systems and machines, the person has to
be informed of the state of the art and the applicable national, European and international
laws, directives and standards.
It is the company’s responsibility only to employ personnel who
}Are familiar with the basic regulations concerning health and safety / accident prevention,
}Have read and understood the information provided in the section entitled Safety
}Have a good knowledge of the generic and specialist standards applicable to the specific
application.

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 8
Warranty and liability
All claims to warranty and liability will be rendered invalid if
}The product was used contrary to the purpose for which it is intended,
}Damage can be attributed to not having followed the guidelines in the manual,
}Operating personnel are not suitably qualified,
}Any type of modification has been made (e.g. exchanging components on the PCB
boards, soldering work etc.).
Disposal
}In safety-related applications, please comply with the mission time TM in the safety-related
characteristic data.
}When decommissioning, please comply with local regulations regarding the disposal of
electronic devices (e.g. Electrical and Electronic Equipment Act).
For your safety
DANGER!
Risk to life due to manipulation/defeat of the safeguard
If replacement actuators are obtained, these must be installed as described
in the chapter entitled Installation.
If replacement actuators are used manipulatively or the function of the safe-
guard is defeated, there is a risk to life when operating the plant or machine!
This must be considered in the operator's hazard assessment and the oper-
ator must define appropriate measures to exclude manipulation.
}Do not remove the connector's protective cap until you are just about to connect the unit.
This will prevent potential contamination.

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 9
Unit features
}Transponder technology for presence detection
}Device types Pilz coding type:
– PSEN sl-0.5n 2.1: fully coded
– PSEN sl-0.5n 2.2: uniquely coded
}different actuators available (see Order reference [ 33])
– Standard actuator PSEN sl-0.5
– free-moving actuator PSEN sl-0.5fm for special applications with higher tolerance
compensation
}Dual-channel operation
}2 safety outputs
}Magnetic guard locking for process protection
}1 input to switch the locking magnet on/off
}LEDs for
– Supply voltage/fault
– Gate closed
– State of the magnetic guard locking device
}M12, 5-pin male connector
Function description
UB
A1 A2
S31
12
22
Power supply
Power/Fault &
&
Safety Gate Lock
Receiver
Magnet
Actuator
There is a high signal at safety outputs 12 and 22 if the following occur simultaneously:
}The actuator is within the response range (safety gate closed) and
}There is a high signal at the input S31 (control command for magnetic guard locking) and
}The holding force of the locking magnet has been tested successfully.

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 10
There is a low signal at safety outputs 12 and 22 if at least one of the following conditions
are met:
}The actuator is outside the response range or
}There is a low signal at the input S31 (control command for magnetic guard locking) or
}The holding force of the locking magnet has not been tested successfully.
Magnetic guard locking device and magnet monitoring
}The locking magnet is switched on if there is a high signal at input S31 (control command
for magnetic guard locking) and the actuator is detected (safety gate closed).
}The holding force of the locking magnet is tested on power-up.
}After a signal change at the input S31 to low, wait for at least 500ms, before supplying a
high signal again at the input S31. Also note the max. switching frequency (see Technical
details: System with normal actuator [ 25], System with free-moving
actuator [ 28], under electrical data).
If an open winding or a winding short circuit is detected on a locking magnet that is
switched on, safety outputs 12 and 22 switch to a low state.
}For physical reasons, a remanence (residual magnetism) remains after the locking mag-
net is switched off; this is dissipated the first time the sensor and actuator are separated.
Therefore a higher effort is required when opening for the first time.
}If the safety gate is in a locked condition and is opened by force, the safety outputs will
shut down.
Lateral and vertical offset
}Max. vertical offset: 5 mm
}Max. lateral offset: 3 mm

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 11
Wiring
Please note:
}You must comply with the specifications stated in the technical details (see Technical de-
tails: System with normal actuator [ 25], System with free-moving actuator [ 28]).
}The power supply must meet the regulations for extra low voltages with protective elec-
trical separation (SELV, PELV).
}The inputs and outputs of the safety switch must have protective separation from
voltages over 60 VDC.
}Ensure the wiring and EMC requirements of EN 60204-1 are met.
}UL requirement: The supply voltage to the safety switch must be protected with a quick-
acting fuse (see Technical details [ 25]).
Guidelines for cable length
The max. cable length depends on the voltage drop at the safety switches. The level of
voltage drop is determined by the:
}Cable resistance
}Current of the device and the current load of the outputs
If the level of the supply voltage at the device connector falls below the minimum permitted
value (see Technical details: System with normal actuator [ 25], System with free-mov-
ing actuator [ 28]), the locking magnet is no longer activated reliably. The "Lock" LED
registers an error when guard locking.
Possible remedies:
}Set the supply voltage constantly to the upper tolerance range (see Technical details:
System with normal actuator [ 25], System with free-moving actuator [ 28]).
}Select a higher conductor cross section
}Reduce load at the outputs, e.g. with evaluation device PNOZe1.1p
Recommended cable cross sections
Prerequisite:
}Supply voltage: 24V
}Cable type: LiYY 5x0.25 mm² (79Ohm/km) from Pilz
Max. load per safety output 100mA 500mA
Cable length 65m 28m
If cable lengths greater than those stated in the table are required, please contact Pilz.

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 12
Pin assignment
12
3
5
4
5-pin M12 male connector
PIN Function Terminal designation Cable colour (Pilz
cable)
1 +24 V UB A1 Brown
2 Output, channel1 12 White
3 0 V UB A2 Blue
4 Output, channel2 22 Black
5 "Lock_Unlock" S31 Grey
The wire colour also applies for the cable available from Pilz as an accessory.
Connection to evaluation devices
Make sure that the selected evaluation device has the following properties:
}2-channel with feasibility monitoring
}OSSD signals are evaluated
Connection diagram, single connection
24 V 0 V
A1
A2
S31 12 22
O1 (ST) I1 (FS) I2 (FS)
A1
A2
FS: Failsafe
ST: Standard
Actuator
Safety switch
Evaluation device
The safety switch PSEN sl-0.5n 2.1/2.2 can be connected to Pilz evaluation devices, for ex-
ample.

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 13
Suitable Pilz evaluation devices are, for example:
}PNOZelog for safety gate monitoring
}PNOZpower for safety gate monitoring
}PNOZsigma for safety gate monitoring
}PNOZ X for safety gate monitoring
}PNOZmulti for safety gate monitoring
Configure the safety switch in the PNOZmulti Configurator with switch type 3.
}PSS for safety gate monitoring with standard function block SB064, SB066 or
FS_SafetyGate
The correct connection to the respective evaluation device is described in the operating
manual for the evaluation device. Make sure that the connection is made in accordance
with the specifications in the operating manual for the selected evaluation device.
The connections to two evaluation devices are shown on the following pages, by way of ex-
ample:
}PNOZ s3 and
}PNOZmulti
Connection example PNOZs3
PNOZ s3 PSENslock
0 V
24 V
A1
A2
S22
S12
A1
A2
S31
12
22
1
3
5
2
4

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 14
Connection example PNOZmulti
2
4
5
PNOZmulti PSENslock
green
yellow
red
I0
I1
12
22
S31
A1
A2
3
1
0 V 24 V
O1
Legend:
I0 Input OSSD
I1 Input OSSD
I2 Signal input
O1 Lock/Unlock

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 15
Teaching in the actuator
PSEN sl-0.5n 2.1
Teaching in the actuator for the first time:
The first corresponding actuator to be detected by the safety switch (see Technical details:
System with normal actuator [ 25], System with free-moving actuator [ 28]) is auto-
matically taught in as soon as it is brought into the response range.
To teach in a new actuator:
}The actuator that is to be taught in must be brought into the safety switch's response
range as the only transponder. As soon as the actuator is detected, the "Safety Gate"
LED switches to a yellow flashing light.
}After a waiting period of 20 s has elapsed, the "Safety Gate" LED switches to quick yellow
flashes. Trigger a system reset in the next 120 s by interrupting the power supply.
}When the device is switched back on, the learning procedure is complete and the number
of permitted additional learning procedures is reduced by 1.
}A maximum of 8 learning procedures are possible.
NOTICE
The actuator must not be removed during the learning procedure.
INFORMATION
This actuator cannot be retaught on the same safety switch.
PSEN sl-0.5n 2.2
The first corresponding actuator to be detected by the safety switch (see Technical details:
System with normal actuator [ 25], System with free-moving actuator [ 28], under
mechanical data) is automatically taught in as soon as it is brought into the response range.
NOTICE
No other actuator may be taught in once this actuator has been taught.

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 16
Installation
}The safety gate system can be installed on left or right-hinged swing gates or on sliding
gates.
WARNING!
Potential loss of safety function due to gross manipulation
Depending on the application, serious injury or death may result.
Use appropriate installation measures to prevent
– The wiring being modified.
– A short circuit being generated on the connector.
– The possibility of using a second actuator to open the safety gate.
CAUTION!
The unit's properties may be affected if installed in an environment contain-
ing electrically or magnetically conductive material. Please check the oper-
ating distances and the assured release distance.
}Safety switches and actuators must be positioned so that they are secured against a
change of position.
}Also note the max. angular offset (see Technical details: System with normal
actuator [ 25], System with free-moving actuator [ 28]).
}The access to the safety switch and actuator has to be possible for maintenance and
checking the correct operation.
}Use reliable fastening elements. A tool is to be required to loosen the fastening elements.
}Prevent self-loosening of the fastening elements of safety switch and actuator.
}The fastening of safety switch and actuator has to be sufficiently stable to ensure the
proper operation of the safety switch and the actuator.
}Prevent the safety switch and actuator being exposed to heavy shock or vibration.
}Circumvention of the safety switch in a reasonably foreseeable manner must be preven-
ted.
}Installation measures in accordance with EN ISO 14119
– Use permanently secured safety screws with a flat head to attach the safety switch
and the actuator (e.g. cheese-head or pan head screws) or rivets.
}Alignment errors of the guard must not adversely affect the safety function of the guard.
INFORMATION
Mounting brackets are available as accessories [ 33].

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 17
Note regarding the free-moving actuator PSEN sl-0.5fm
The free-moving actuators PSEN sl-0.5fm are fitted with a movable metal plate. For this
reason, a recess must be provided in the mounting surface for the screw connection.
A (2:1)
Ø10
3A
91
WARNING!
Risk of death and serious injury by reaching into the danger zone!
The actuators enable a warped gate to be closed. A gap may occur on the
gate as a result. Make sure that the gap remains small enough to exclude
the possibility of reaching into the danger zone.

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 18
Installing on a swing gate
Align the actuator flush with the edge of the gate at the
height required and tighten the screws.
Close gate.
Align the mounting bracket flush with the safety switch
and tighten the screws.
Align the safety switch and mounting bracket with the
actuator and tighten the screws.

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 19
Installing on a sliding gate
Align the actuator mounting bracket flush with the sliding
gate and tighten the screws.
Install the actuator at the height required.
Align the safety switch mounting bracket flush with the
frame and fasten with screws.
(Important: do not tighten the screws)
Fix safety switch upright with a screw (a), close gate.
(a)
Align mounting brackets, press firmly together and tighten
screw (b).
(b)

PSEN sl-0.5n 2.1/2.2
Operating Manual PSEN sl-0.5n 2.1/2.2
1003805-EN-03 | 20
Remove the safety switch and tighten screw (c).
(c)
Align the safety switch to the actuator and tighten the
screws.
Adjustment
}The stated operating distances (see Technical details: System with normal
actuator [ 25], System with free-moving actuator [ 28]) only apply when the
safety switch and actuator are installed facing each other in parallel. Operating distances
may deviate if other arrangements are used.
}Note the maximum permitted lateral and vertical offset (see Lateral and vertical
offset [ 10]).